Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (w/ Multi-display) › 2015.08–2018.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255488 AUDIO AND VISUAL SYSTEM(w/ Multi-display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Multi-display)  Display Signal Circuit between Multi-display and Radio Receiver  


DESCRIPTION

The display image signal from the multi-media module receiver assembly is sent to the multi-display assembly using a digital communication cable.

WIRING DIAGRAM

E306678E44
1.396,0.865 1.802,1.021 0.406,0.156 10 false GV+ 1.406,1.292 1.813,1.448 0.406,0.156 10 false GV- 1.385,1.74 1.792,1.896 0.406,0.156 10 false GVG 0.792,2.219 1.198,2.375 0.406,0.156 10 false F108 0.792,2.396 2.292,2.563 1.5,0.167 10 false Multi-display Assembly 1.813,0.719 2.219,0.875 0.406,0.156 10 false 1 1.813,1.156 2.219,1.313 0.406,0.156 10 false 2 1.823,1.656 2.229,1.813 0.406,0.156 10 false 3 0.354,3.146 1.854,3.313 1.5,0.167 10 false *: Shielded 0.917,3.385 2.417,3.552 1.5,0.167 10 false : GVIF Cable 3.542,1.938 3.76,2.094 0.219,0.156 10 false * 5.281,0.74 5.688,0.896 0.406,0.156 10 false 1 5.281,1.188 5.688,1.344 0.406,0.156 10 false 2 5.292,1.656 5.698,1.813 0.406,0.156 10 false 3 5.521,0.844 5.927,1 0.406,0.156 10 false GVI+ 5.51,1.323 5.917,1.479 0.406,0.156 10 false GVI- 5.51,1.781 5.917,1.938 0.406,0.156 10 false GVG1 5.25,2.208 5.656,2.365 0.406,0.156 10 false F107 5.25,2.354 7.063,2.719 1.813,0.365 10 false Multi-media Module Receiver Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (GVIF CABLE)
a.

Check if the GVIF cable connectors between the multi-media module receiver assembly and the multi-display assembly have any connection problems.

OK:

There is no connection problems.




OK

2.CHECK HARNESS AND CONNECTOR (GVIF CABLE)

NG

REMOVE CONNECTION PROBLEM (GVIF CABLE)

2.CHECK HARNESS AND CONNECTOR (GVIF CABLE)
a.
U166481E02
0.615,0.479 0.844,0.479 0.844,0.479 1.177,0.865 false 0.896,2.188 1.125,2.188 1.125,2.188 1.458,2.563 false 2.542,2.188 2.313,2.188 2.313,2.188 1.979,2.563 false 0.708,1.458 0.938,1.458 0.938,1.458 1.229,1.167 false 0.958,3.073 1.188,3.073 1.188,3.073 1.479,2.781 false 1.146,0.125 1.375,0.125 1.375,0.125 1.469,0.854 false 0.073,0.052 0.344,0.292 0.271,0.24 10 false *a 0.083,1.719 0.354,1.958 0.271,0.24 10 false *b 0.25,0.438 0.604,0.667 0.354,0.229 10 false GVI+ 2.792,0.844 3.146,1.073 0.354,0.229 10 false F107 0.552,2.115 0.875,2.344 0.323,0.229 10 false GV+ 2.604,2.115 2.927,2.344 0.323,0.229 10 false GV- 0.26,1.375 0.677,1.604 0.417,0.229 10 false GVG1 0.604,2.979 0.958,3.208 0.354,0.229 10 false GVG 0.802,0.063 1.135,0.292 0.333,0.229 10 false GVI- 2.479,2.573 2.833,2.802 0.354,0.229 10 false F108

Remove the GVIF cable from the multi-media module receiver assembly and multi-display assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F107-1 (GVI+) - F108-1 (GV+) Always Below 1 Ω
F107-2 (GVI-) - F108-2 (GV-) Always Below 1 Ω
F107-3 (GVG1) - F108-3 (GVG) Always Below 1 Ω
F107-1 (GVI+) or F108-1 (GV+) - Body ground Always 10 kΩ or higher
F107-2 (GVI-) or F108-2 (GV-) - Body ground Always 10 kΩ or higher
F107-3 (GVG1) or F108-3 (GVG) - Body ground Always 10 kΩ or higher


Text in Illustration
*a GVIF Cable
(to Multi-media Module Receiver Assembly)
*b GVIF Cable
(to Multi-display Assembly)



OK

3.CHECK MULTI-DISPLAY ASSEMBLY

NG

REPLACE HARNESS AND CONNECTOR (GVIF CABLE)

3.CHECK MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a new or known good one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY (w/ Navigation System)>REMOVAL).


b.

Check that the screen display is normal.

OK:

Screen display is normal.




OK

END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE