Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (w/ Multi-display) › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255488 AUDIO AND VISUAL SYSTEM(w/ Multi-display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Multi-display)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

The multi-media module receiver assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E240105E78
5.031,1.76 5.448,1.969 0.417,0.208 10 false F77 5.021,1.979 6.104,2.354 1.083,0.375 10 false Multi-media Module Receiver Assembly 4.917,0.948 5.219,1.146 0.302,0.198 10 false 56 5.24,1.052 5.583,1.219 0.344,0.167 10 false SPD 1.76,1.063 2.021,1.281 0.26,0.219 10 false +S 2.104,0.948 2.25,1.125 0.146,0.177 10 false 6 0.771,1.74 1.24,1.958 0.469,0.219 10 false E119 0.771,1.938 2.25,2.323 1.479,0.385 10 false Combination Meter Assembly

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U166389E01
0.099,0.128 0.311,0.301 0.212,0.173 10 *a 1.531,0.434 2.039,0.582 0.508,0.148 10 E119 1.138,3.849 1.398,3.997 0.260,0.148 10 A 2.791,3.578 3.129,3.726 0.338,0.148 10 GND 2.582,1.957 2.843,2.105 0.260,0.148 10 +S 2.196,1.317 2.421,2.046 2.421,2.046 2.537,2.046 false

Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


ii.

Connect an oscilloscope to terminal E119-6 (+S) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal E119-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





OK

NG

2.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the E119 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-56 (SPD) - E119-6 (+S) Always Below 1 Ω
F77-56 (SPD) or E119-6 (+S) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR