The parking assist ECU and multi-media module receiver assembly are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the multi-media module receiver assembly and parking assist ECU, these DTCs will be stored.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B15D8* | A device that is listed in the AVC-LAN connected device record of the master unit is missing. | ·
Parking assist ECU power source circuit ·
AVC-LAN circuit ·
Parking assist ECU ·
Multi-media module receiver assembly |
*: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
The multi-media module receiver assembly is the master unit.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Clear the DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (w/ Multi-display)>DTC CHECK / CLEAR).
NEXT
Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (w/ Multi-display)>DTC CHECK / CLEAR).
No DTCs are output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F75-4 (GND1) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F75-1 (+B) - F75-4 (GND1) | Always | 11 to 14 V |
| F75-8 (IG) - F75-4 (GND1) | Engine switch on (IG) | 11 to 14 V |
| F75-9 (ACC) - F75-4 (GND1) | Engine switch on (ACC) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Parking Assist ECU) |
OK
NG
Remove the multi-media module receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/ Multi-display)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (TX1+) - 8 (TX1-) | Always | 60 to 80 Ω |
OK
NG
Disconnect the F77 multi-media module receiver assembly connector.
Disconnect the F75 parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F77-7 (TX1+) - F75-11 (TX+) | Always | Below 1 Ω |
| F77-8 (TX1-) - F75-10 (TX-) | Always | Below 1 Ω |
| F77-7 (TX1+) - Body ground | Always | 10 kΩ or higher |
| F77-8 (TX1-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the parking assist ECU with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU>REMOVAL).
NEXT
Clear the DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (w/ Multi-display)>DTC CHECK / CLEAR).
NEXT
Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (w/ Multi-display)>DTC CHECK / CLEAR).
OK
NG