Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  AVC-LAN Circuit  


DESCRIPTION

Each audio system component connected to the AVC-LAN (communication bus) transfers switch signals using the audio visual communication local area network.

If a short to +B or short to ground occurs in the AVC-LAN, the audio system will not function normally because communication is not possible.

WIRING DIAGRAM

E330590E10
1.104,1.125 1.427,1.302 0.323,0.177 10 false TX- 1.094,0.646 1.417,0.823 0.323,0.177 10 false TX+ 1.438,0.531 1.656,0.708 0.219,0.177 10 false 11 1.438,1 1.656,1.177 0.219,0.177 10 false 10 0.365,1.49 0.656,1.656 0.292,0.167 10 false F75 0.365,1.646 1.667,1.865 1.302,0.219 10 false Parking Assist ECU 3.042,0.656 3.438,0.823 0.396,0.167 10 false TX1+ 3.042,1.115 3.438,1.281 0.396,0.167 10 false TX1- 3.583,0.635 3.979,0.802 0.396,0.167 10 false TX3+ 3.583,1.135 3.979,1.302 0.396,0.167 10 false TX3- 5.583,0.656 5.979,0.823 0.396,0.167 10 false TX+ 5.594,1.125 5.99,1.292 0.396,0.167 10 false TX- 2.885,0.531 3.042,0.698 0.156,0.167 10 false 7 5.406,0.521 5.563,0.688 0.156,0.167 10 false 7 2.885,1.021 3.042,1.188 0.156,0.167 10 false 8 4,0.521 4.198,0.698 0.198,0.177 10 false 45 4,1.01 4.198,1.188 0.198,0.177 10 false 46 5.344,1.021 5.542,1.198 0.198,0.177 10 false 19 2.854,1.542 3.188,1.708 0.333,0.167 10 false F77 2.854,1.729 4.198,2.104 1.344,0.375 10 false Multi-media Module Receiver Assembly 5.375,1.729 5.708,1.896 0.333,0.167 10 false F79 5.365,1.896 7.094,2.083 1.729,0.188 10 false Multi-display Assembly 0.771,2.333 2.833,2.51 2.063,0.177 10 false : AVC-LAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION).


PROCEDURE

1.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
E238990E22
2.365,1.01 2.833,0.573 false 2.24,1 1.917,0.635 false 2.26,1.375 1.99,1.781 false 2.385,1.375 2.656,1.74 false 2.885,0.479 3.281,0.656 0.396,0.177 10 false TX1+ 1.813,1.813 2.208,1.99 0.396,0.177 10 false TX3- 2.5,1.771 2.896,1.948 0.396,0.177 10 false TX3+ 1.583,0.521 1.979,0.698 0.396,0.177 10 false TX1-

Remove the multi-media module receiver assembly with the connector(s) still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/ Multi-display)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (TX1+) - 8 (TX1-) Always 60 to 80 Ω
45 (TX3+) - 46 (TX3-) Always 60 to 80 Ω




OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the F79 multi-display assembly connector.


c.

Disconnect the F75 parking assist ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-45 (TX3+) - F79-7 (TX+) Always Below 1 Ω
F77-46 (TX3-) - F79-19 (TX-) Always Below 1 Ω
F77-7 (TX1+) - F75-11 (TX+) Always Below 1 Ω
F77-8 (TX1-) - F75-10 (TX- ) Always Below 1 Ω
F77-45 (TX3+) - Body ground Always 10 kΩ or higher
F77-46 (TX3-) - Body ground Always 10 kΩ or higher
F77-7 (TX1+) - Body ground Always 10 kΩ or higher
F77-8 (TX1-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

When disconnecting a slave unit causes the master unit to return to normal operation, this indicates that the slave unit is malfunctioning. Replace the malfunctioning slave unit.



OK:

Master unit returns to normal operation.




OK

REPLACE MALFUNCTIONING PARTS

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY