Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D8  Monitor Disconnected  


DESCRIPTION

The parking assist ECU and multi-media module receiver assembly are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the multi-media module receiver assembly and parking assist ECU, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D8* A device that is listed in the AVC-LAN connected device record of the master unit is missing.
·

Parking assist ECU power source circuit

·

AVC-LAN circuit

·

Parking assist ECU

·

Multi-media module receiver assembly



HINT:
·

*: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The multi-media module receiver assembly is the master unit.



WIRING DIAGRAM

E245658E31
0.896,0.844 2.375,1.01 1.479,0.167 10 false from Battery 0.354,1.25 1.719,1.427 1.365,0.177 10 false from IG1 NO. 1 Relay 0.656,1.677 1.802,1.906 1.146,0.229 10 false from ACC Relay 1.958,1 2.917,1.177 0.958,0.177 10 false RAD NO.1 1.875,1.417 2.833,1.594 0.958,0.177 10 false ECU-IG NO. 2 2.125,1.833 2.865,2.021 0.74,0.188 10 false ACC 3.146,0.854 3.885,1.042 0.74,0.188 10 false +B 3.146,1.271 3.885,1.458 0.74,0.188 10 false IG 3.146,1.688 3.885,1.875 0.74,0.188 10 false ACC 3.135,2.115 3.875,2.302 0.74,0.188 10 false GND1 2.948,0.76 3.688,0.948 0.74,0.188 10 false 1 2.958,1.167 3.698,1.354 0.74,0.188 10 false 8 2.969,1.594 3.708,1.781 0.74,0.188 10 false 9 2.979,1.979 3.719,2.167 0.74,0.188 10 false 4 3.781,1.26 4.521,1.448 0.74,0.188 10 false TX+ 3.802,1.677 4.542,1.865 0.74,0.188 10 false TX- 4.094,1.146 4.833,1.333 0.74,0.188 10 false 11 4.094,1.552 4.833,1.74 0.74,0.188 10 false 10 5.51,1.135 6.25,1.323 0.74,0.188 10 false 7 5.521,1.563 6.26,1.75 0.74,0.188 10 false 8 5.75,1.26 6.49,1.448 0.74,0.188 10 false TX1+ 5.76,1.635 6.5,1.823 0.74,0.188 10 false TX1- 5.604,2.167 6.344,2.354 0.74,0.188 10 false F77 5.594,2.344 6.833,2.708 1.24,0.365 10 false Multi-media Module Receiver Assembly 3,2.531 3.74,2.719 0.74,0.188 10 false F75 3,2.719 4.646,2.917 1.646,0.198 10 false Parking Assist ECU 0.844,3.448 2.885,3.594 2.042,0.146 10 false : AVC-LAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

2.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output




OK

NG

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
U166292E02
2.563,0.958 2.76,0.531 2.76,0.531 2.833,0.531 false 1.469,1.302 1.833,1.813 1.833,1.813 1.896,1.813 false 1.323,1.313 1.125,1.823 1.125,1.823 1.021,1.823 false 0.813,0.958 0.625,0.438 0.625,0.438 0.51,0.438 false 1.583,0.344 1.906,0.531 0.323,0.188 10 false F75 2.885,0.458 3.385,0.646 0.5,0.188 10 false GND1 1.948,1.74 2.448,1.927 0.5,0.188 10 false ACC 0.813,1.74 1.01,1.927 0.198,0.188 10 false IG 0.26,0.354 0.51,0.542 0.25,0.188 10 false +B 0.083,0.042 0.333,0.229 0.25,0.188 10 false *a

Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F75-4 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F75-1 (+B) - F75-4 (GND1) Always 11 to 14 V
F75-8 (IG) - F75-4 (GND1) Engine switch on (IG) 11 to 14 V
F75-9 (ACC) - F75-4 (GND1) Engine switch on (ACC) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)


OK

4.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
E238990E09
2.854,0.458 3.253,0.635 0.399,0.177 10 TX1+ 1.48,0.458 1.879,0.635 0.399,0.177 10 TX1- 2.372,1.038 2.737,0.544 2.737,0.544 2.823,0.544 false 2.264,1.046 1.972,0.522 1.972,0.522 1.891,0.522 false

Remove the multi-media module receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/ Multi-display)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (TX1+) - 8 (TX1-) Always 60 to 80 Ω




OK

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - PARKING ASSIST ECU)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the F75 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-7 (TX1+) - F75-11 (TX+) Always Below 1 Ω
F77-8 (TX1-) - F75-10 (TX-) Always Below 1 Ω
F77-7 (TX1+) - Body ground Always 10 kΩ or higher
F77-8 (TX1-) - Body ground Always 10 kΩ or higher




OK

6.REPLACE PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE PARKING ASSIST ECU
a.

Replace the parking assist ECU with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU>REMOVAL).



NEXT

7.CLEAR DTC
8.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).



OK

END (PARKING ASSIST ECU IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY