The parking assist ECU and multi-media module receiver assembly are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the multi-media module receiver assembly and parking assist ECU, these DTCs will be stored.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B15D8* | A device that is listed in the AVC-LAN connected device record of the master unit is missing. | ·
AVC-LAN circuit ·
Parking assist ECU ·
Multi-media module receiver assembly |
*: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
The multi-media module receiver assembly is the master unit.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION).
Clear the DTCs (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).
No DTCs are output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F75-4 (GND1) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F75-1 (+B) - F75-4 (GND1) | Always | 11 to 14 V |
| F75-8 (IG) - F75-4 (GND1) | Engine switch on (IG) | 11 to 14 V |
| F75-9 (ACC) - F75-4 (GND1) | Engine switch on (ACC) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Parking Assist ECU) |
OK
NG
Remove the multi-media module receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/ Multi-display)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (TX1+) - 8 (TX1-) | Always | 60 to 80 Ω |
OK
NG
Disconnect the F77 multi-media module receiver assembly connector.
Disconnect the F75 parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F77-7 (TX1+) - F75-11 (TX+) | Always | Below 1 Ω |
| F77-8 (TX1-) - F75-10 (TX-) | Always | Below 1 Ω |
| F77-7 (TX1+) - Body ground | Always | 10 kΩ or higher |
| F77-8 (TX1-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the parking assist ECU with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU>REMOVAL).
NEXT
Clear the DTCs (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).
No DTCs are output.
OK
NG