Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Visual Mute Signal Circuit between Navigation ECU and Multi-display  


DESCRIPTION

The multi-media module receiver assembly sends a visual mute signal to the multi-display assembly. As a result, a black screen is inserted when the screen changes so that noise and distorted images are not displayed.

When an open exists in the circuit, noise and distorted images will be displayed instead of a black screen.

When a short exists in the circuit, even though the multi-display assembly is operating normally, noise and distorted images will be displayed (black screen will not be displayed) during screen changes or the black screen will always be displayed.

WIRING DIAGRAM

E245681E84
0.677,1.646 3.292,1.969 2.615,0.323 10 false Multi-display Assembly 1.49,0.917 1.906,1.073 0.417,0.156 10 false VMTI 2,0.813 2.146,0.958 0.146,0.146 10 false 11 4.99,1.667 6.344,2.031 1.354,0.365 10 false Multi-media Module Receiver Assembly 5.26,0.927 5.719,1.083 0.458,0.156 10 false VMTF 5.063,0.833 5.271,1.042 0.208,0.208 10 false 10 0.677,1.49 1.031,1.698 0.354,0.208 10 false F79 4.99,1.51 5.26,1.677 0.271,0.167 10 false F77

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)
a.

Disconnect the F79 multi-display assembly connector.


b.

Disconnect the F77 multi-media module receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-11 (VMTI) - F77-10 (VMTF) Always Below 1 Ω
F79-11 (VMTI) - Body ground Always 10 kΩ or higher




OK

2.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
U166567E01
0.037,0.005 0.521,0.166 0.485,0.161 10 *a 2.402,1.777 2.984,1.937 0.582,0.161 10 VMTF 1.653,0.438 2.116,0.599 0.463,0.161 10 F77 1.877,1.062 2.304,1.858 2.304,1.858 2.371,1.858 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F77-10 (VMTF) - Body ground Engine switch on (ACC), screen display changes. 3.5 V or higher → Below 1 V → 3.5 V or higher


Text in Illustration
*a Component with harness connected
(Multi-media Module Receiver Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY