Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2015.08–2016.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The multi-media module receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC Code DTC Detection Condition Trouble Area
B1579 Telephone microphone signal is lost.
·

Multi-media module receiver assembly

·

Map light assembly

·

Telephone microphone assembly

·

Harness or connector



WIRING DIAGRAM

E333228E09
1.792,0.333 2.177,0.49 0.385,0.156 10 false SNS2 1.833,1.177 2.344,1.333 0.51,0.156 10 false ACC 1.844,0.76 2.417,0.917 0.573,0.156 10 false MI1+ 1.854,1.594 2.438,1.75 0.583,0.156 10 false MIC- 0.49,2.646 2.135,2.854 1.646,0.208 10 false Map Light Assembly 0.219,3.313 1.865,3.521 1.646,0.208 10 false *: Shielded 5.823,2.625 7.052,2.948 1.229,0.323 10 false Multi-media Module Receiver Assembly 6.031,0.427 6.458,0.583 0.427,0.156 10 false SNS2 6.052,0.833 6.479,0.99 0.427,0.156 10 false MIN+ 6.042,1.667 6.469,1.823 0.427,0.156 10 false MIN- 6.052,2.063 6.479,2.219 0.427,0.156 10 false SGND 2.292,0.333 2.667,0.49 0.375,0.156 10 false 20 2.313,1.167 2.688,1.323 0.375,0.156 10 false 25 2.302,1.594 2.677,1.75 0.375,0.156 10 false 26 0.479,2.458 0.833,2.615 0.354,0.156 10 false R7 5.813,2.438 6.167,2.594 0.354,0.156 10 false F77 5.729,0.344 5.938,0.5 0.208,0.156 10 false 49 5.729,0.76 5.938,0.917 0.208,0.156 10 false 27 5.729,1.583 5.938,1.74 0.208,0.156 10 false 48 6.042,1.25 6.469,1.406 0.427,0.156 10 false MACC 2.302,0.75 2.677,0.906 0.375,0.156 10 false 27 5.729,1.177 5.938,1.333 0.208,0.156 10 false 29 5.729,1.99 5.938,2.146 0.208,0.156 10 false 28 0.635,1.063 1.458,1.594 0.823,0.531 10 false Telephone Microphone Assembly 3.958,2.229 4.094,2.406 0.135,0.177 10 false * 5.042,2.229 5.177,2.406 0.135,0.177 10 false *

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY -MAP LIGHT ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the R7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-27 (MIN+) - R7-27 (MI1+) Always Below 1 Ω
F77-29 (MACC) - R7-25 (ACC) Always Below 1 Ω
F77-48 (MIN-) - R7-26 (MIC-) Always Below 1 Ω
F77-49 (SNS2) - R7-20 (SNS2) Always Below 1 Ω
F77-27 (MIN+) - Body ground Always 10 kΩ or higher
F77-28 (SGND) - Body ground Always 10 kΩ or higher
F77-29 (MACC) - Body ground Always 10 kΩ or higher
F77-48 (MIN-) - Body ground Always 10 kΩ or higher
F77-49 (SNS2) - Body ground Always 10 kΩ or higher




OK

2.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
U166566E01
0.037,0.005 0.521,0.166 0.485,0.161 10 *a 1.027,1.931 1.465,2.092 0.438,0.161 10 SGND 1.787,1.232 1.609,2.013 1.609,2.013 1.543,2.013 false 0.615,1.725 1.074,1.886 0.460,0.161 10 MACC 1.683,1.232 1.231,1.807 1.231,1.807 1.165,1.807 false 2.402,1.777 2.887,1.937 0.485,0.161 10 MIN- 1.64,0.451 2.103,0.611 0.463,0.161 10 F77 1.887,1.352 2.305,1.858 2.305,1.858 2.371,1.858 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F77-29 (MACC) - Body ground Engine switch on (ACC) 4 to 6 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-28 (SGND) - Body ground Always Below 1 Ω
F77-48 (MIN-) - Body ground Always Below 1 Ω



Text in Illustration
*a Component with harness connected
(Multi-media Module Receiver Assembly)


OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

3.INSPECT MAP LIGHT ASSEMBLY
a.
E262715E14
0.847,1.497 1.244,1.662 0.397,0.165 10 MIC- 2.476,1.512 2.873,1.693 0.397,0.181 10 SNS2 2.162,1.186 2.269,1.587 2.269,1.587 2.428,1.587 false 1.508,1.187 1.418,1.578 1.418,1.578 1.293,1.578 false

Remove the map light assembly (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
20 (SNS2) - 26 (MIC-) Always Below 1 Ω




OK

4.CHECK MAP LIGHT ASSEMBLY

NG

5.CHECK TELEPHONE MICROPHONE ASSEMBLY
4.CHECK MAP LIGHT ASSEMBLY
a.
U156709E01
1.55,0.278 1.872,0.461 0.323,0.184 10 R7 2.118,1.695 2.535,1.872 0.416,0.177 10 MIC- 0.73,1.717 1.175,1.893 0.444,0.177 10 MI1+ 0.146,0.063 0.422,0.279 0.276,0.217 10 *a 1.494,1.209 1.938,1.79 1.938,1.79 2.067,1.79 false 1.426,1.209 1.311,1.798 1.311,1.798 1.203,1.798 false

Turn the engine switch on (ACC).


b.

Connect an oscilloscope to terminals R7-27 (MI1+) and R7-26 (MIC-) of the map light assembly connector.


c.

Check the waveform of the telephone microphone assembly using the oscilloscope.

Text in Illustration
*a Component with harness connected
(Map Light Assembly)

Result
Result Proceed to
A waveform synchronized with the voice input to the map light assembly is output. A
A waveform synchronized with the voice input to the map light assembly is not output. B



A

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

B

5.CHECK TELEPHONE MICROPHONE ASSEMBLY
5.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL).


b.

Check if the same DTC is output again.

OK:

No DTCs are output.




OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG