Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255497 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Clearance Sonar Main Switch Circuit  


DESCRIPTION

When the back sonar or clearance sonar switch assembly turns on, the ON signal is input into the parking assist ECU*1 or clearance warning ECU assembly*2.

*1: w/ Side Monitor System

*2: w/o Side Monitor System


WIRING DIAGRAM

E246938E03
5.823,0.917 6.323,1.135 0.5,0.219 10 false CSSW 3.781,0.823 4.135,1.031 0.354,0.208 10 false ECU 2.344,1.313 2.688,1.5 0.344,0.188 10 false G15 2.344,1.458 4.344,1.865 2,0.406 10 false Back Sonar or Clearance Sonar Switch Assembly 4.167,0.823 4.365,1.042 0.198,0.219 10 false 9 2.458,0.823 2.635,1.021 0.177,0.198 10 false 6 2.646,0.823 2.823,0.979 0.177,0.156 10 false IG 0.125,0.917 1.729,1.177 1.604,0.26 10 false from ECU-IG No. 1 Fuse 5.635,1.917 7.094,2.177 1.458,0.26 10 false Parking Assist ECU 5.635,1.76 5.958,1.969 0.323,0.208 10 false F76 5.542,0.823 5.75,1.021 0.208,0.198 10 false 25 0.052,0.073 2.729,0.302 2.677,0.229 12 false w/ Side Monitor System:

E246938E04
5.802,0.906 6.354,1.146 0.552,0.24 10 false CSSW 3.781,0.833 4.104,0.99 0.323,0.156 10 false ECU 2.333,1.313 2.896,1.594 0.563,0.281 10 false G15 2.333,1.448 4.427,1.885 2.094,0.438 10 false Back Sonar or Clearance Sonar Switch Assembly 4.177,0.833 4.469,1.073 0.292,0.24 10 false 9 2.448,0.833 2.625,1.021 0.177,0.188 10 false 6 2.646,0.833 2.823,0.99 0.177,0.156 10 false IG 0.146,0.917 1.698,1.177 1.552,0.26 10 false from ECU-IG No. 1 Fuse 0.073,0.094 2.75,0.323 2.677,0.229 12 false w/o Side Monitor System: 5.688,1.948 6.938,2.344 1.25,0.396 10 false Clearance Warning ECU Assembly 5.698,1.781 6,1.969 0.302,0.188 10 false F12 5.573,0.823 5.792,1.063 0.219,0.24 10 false 12

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY)
a.

Check the Data List for proper functioning of the back sonar or clearance sonar main switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>DATA LIST / ACTIVE TEST).

Clearance Sonar
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main Switch Back sonar or clearance sonar switch assembly / ON or OFF OFF: Back sonar or clearance sonar switch assembly off
ON: Back sonar or clearance sonar switch assembly on
-

OK:

The intelligent tester display changes according to operation of back sonar or clearance sonar switch assembly.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
a.

Remove the back sonar or clearance sonar switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>REMOVAL).


b.

Inspect the back sonar or clearance sonar switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>INSPECTION).

Result
Result Proceed to
OK (w/ Side Monitor System) A
OK (w/o Side Monitor System) B
NG C



A

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - PARKING ASSIST ECU AND BATTERY)

B

4.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)

C

REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - PARKING ASSIST ECU AND BATTERY)
a.

Disconnect the G15 back sonar or clearance sonar switch assembly connector.


b.

Disconnect the F76 parking assist ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G15-6 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G15-9 (ECU) - F76-25 (CSSW) Always Below 1 Ω
G15-9 (ECU) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)
a.

Disconnect the G15 back sonar or clearance sonar switch assembly connector.


b.

Disconnect the F12 clearance warning ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G15-6 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G15-9 (ECU) - F12-12 (CSSW) Always Below 1 Ω
G15-9 (ECU) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR