Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255497 TOYOTA PARKING ASSIST-SENSOR SYSTEM C

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  C1AEC  Front Sensor Communication Malfunction  


DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the front sensors and the ECU, or when there is a malfunction in a front sensor.

DTC Code DTC Detection Condition Trouble Area
C1AEC An open or short circuit in the communication line between the front sensors and ECU or a malfunction in a front sensor during initialization mode after the engine switch is turned on (IG).
·

No. 1 ultrasonic sensor (front side)

·

Harness or connector

·

Parking assist ECU*1

·

Clearance warning ECU assembly*2



*1: w/ Side Monitor System

*2: w/o Side Monitor System


WIRING DIAGRAM

E246937E01
5.942,0.268 6.333,0.420 0.391,0.152 10 CSB1 3.566,0.268 3.716,0.420 0.150,0.152 10 BI 5.777,0.212 5.896,0.364 0.120,0.152 10 5 5.942,0.562 6.255,0.715 0.314,0.152 10 LIN1 3.564,0.562 3.716,0.715 0.152,0.152 10 SI 5.699,0.506 5.896,0.659 0.197,0.152 10 23 5.942,0.846 6.359,0.999 0.418,0.152 10 CSG1 5.659,1.209 5.939,1.361 0.280,0.152 10 F76 5.659,1.348 7.034,1.500 1.375,0.152 10 Parking Assist ECU*1 2.498,1.209 2.778,1.361 0.280,0.152 10 B8 2.498,1.348 4.011,1.692 1.513,0.344 10 No. 1 Ultrasonic Sensor (FL Sensor) 0.282,1.209 0.562,1.361 0.280,0.152 10 B7 0.282,1.348 1.795,1.692 1.513,0.344 10 No. 1 Ultrasonic Sensor (FR Sensor) 0.051,3.064 2.367,3.245 2.316,0.181 10 *1: w/ Side Monitor System 0.051,3.383 2.450,3.564 2.399,0.181 10 *2: w/o Side Monitor System 3.566,0.846 3.716,0.999 0.150,0.152 10 EI 2.901,0.268 3.147,0.420 0.247,0.152 10 BO 2.901,0.562 3.131,0.715 0.230,0.152 10 SO 2.901,0.846 3.129,0.999 0.229,0.152 10 EO 5.777,0.791 5.879,0.943 0.102,0.152 10 6 5.942,1.893 6.333,2.045 0.391,0.152 10 CSB1 5.721,1.837 5.896,1.989 0.175,0.152 10 21 5.942,2.187 6.255,2.340 0.314,0.152 10 LIN1 5.787,2.131 5.897,2.284 0.110,0.152 10 9 5.942,2.472 6.359,2.624 0.418,0.152 10 CSG1 5.659,2.814 5.939,2.966 0.280,0.152 10 F12 5.659,2.953 7.034,3.293 1.375,0.340 10 Clearance Warning ECU Assembly*2 5.72,2.416 5.896,2.568 0.176,0.152 10 19 3.768,0.212 3.887,0.364 0.120,0.152 10 1 3.768,0.506 3.878,0.659 0.110,0.152 10 3 1.55,0.506 1.660,0.659 0.110,0.152 10 3 3.768,0.791 3.870,0.943 0.102,0.152 10 5 1.349,0.268 1.499,0.420 0.150,0.152 10 BI 1.347,0.562 1.499,0.715 0.152,0.152 10 SI 1.348,0.846 1.499,0.999 0.150,0.152 10 EI 1.55,0.212 1.670,0.364 0.120,0.152 10 1 1.55,0.791 1.652,0.943 0.102,0.152 10 5 2.728,0.212 2.848,0.364 0.120,0.152 10 2 2.728,0.506 2.838,0.659 0.110,0.152 10 4 2.728,0.791 2.830,0.943 0.102,0.152 10 6

PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1AEC is output (w/ Side Monitor System) A
DTC C1AEC is output (w/o Side Monitor System) B
DTC C1AEC is not output C



A

2.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [FL SENSOR] - PARKING ASSIST ECU)

B

10.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [FL SENSOR] - CLEARANCE WARNING ECU ASSEMBLY)

C

2.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [FL SENSOR] - PARKING ASSIST ECU)
a.

Disconnect the B8 No. 1 ultrasonic sensor (FL sensor) connector.


b.

Disconnect the F76 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B8-1 (BI) - F76-5 (CSB1) Always Below 1 Ω
B8-3 (SI) - F76-23 (LIN1) Always Below 1 Ω
B8-5 (EI) - F76-6 (CSG1) Always Below 1 Ω
B8-1 (BI) - Body ground Always 10 kΩ or higher
B8-3 (SI) - Body ground Always 10 kΩ or higher
B8-5 (EI) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [FL SENSOR] - NO. 1 ULTRASONIC SENSOR [FR SENSOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [FL SENSOR] - NO. 1 ULTRASONIC SENSOR [FR SENSOR])
a.

Disconnect the B8 No. 1 ultrasonic sensor (FL sensor) connector.


b.

Disconnect the B7 No. 1 ultrasonic sensor (FR sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B8-2 (BO) - B7-1 (BI) Always Below 1 Ω
B8-4 (SO) - B7-3 (SI) Always Below 1 Ω
B8-6 (EO) - B7-5 (EI) Always Below 1 Ω
B8-2 (BO) - Body ground Always 10 kΩ or higher
B8-4 (SO) - Body ground Always 10 kΩ or higher
B8-6 (EO) - Body ground Always 10 kΩ or higher




OK

4.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK PARKING ASSIST ECU
a.
U165798E02
2.396,1.76 2.531,0.979 2.531,0.979 2.75,0.979 true 2.49,1.76 2.75,1.229 2.75,1.229 2.958,1.229 true 0.146,0.125 0.396,0.333 0.25,0.208 10 false *a 1.552,1.083 1.823,1.229 0.271,0.146 10 false F76 2.99,1.146 3.365,1.365 0.375,0.219 10 false CSB1 2.802,0.885 3.24,1.073 0.438,0.188 10 false CSG1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F76-5 (CSB1) - Body ground Engine switch on (IG) 7.2 to 8.8 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-6 (CSG1) - Body ground Always Below 1 Ω



Text in Illustration
*a Component with harness connected
(Parking Assist ECU)


OK

5.CHECK FOR DTC

NG

6.REPLACE NO. 1 ULTRASONIC SENSOR (FL SENSOR)
a.

Replace the No. 1 ultrasonic sensor (FL sensor) with a normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL).



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC

OK

END (NO. 1 ULTRASONIC SENSOR [FL SENSOR] IS DEFECTIVE)

NG

8.REPLACE NO. 1 ULTRASONIC SENSOR (FR SENSOR)
8.REPLACE NO. 1 ULTRASONIC SENSOR (FR SENSOR)
a.

Replace the No. 1 ultrasonic sensor (FR sensor) with a normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL)



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC

OK

END (NO. 1 ULTRASONIC SENSOR [FR SENSOR] IS DEFECTIVE)

NG

10.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [FL SENSOR] - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the B8 No. 1 ultrasonic sensor [FL sensor] connector.


b.

Disconnect the F12 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B8-1 (BI) - F12-21 (CSB1) Always Below 1 Ω
B8-3 (SI) - F12-9 (LIN1) Always Below 1 Ω
B8-5 (EI) - F12-19 (CSG1) Always Below 1 Ω
B8-1 (BI) - Body ground Always 10 kΩ or higher
B8-3 (SI) - Body ground Always 10 kΩ or higher
B8-5 (EI) - Body ground Always 10 kΩ or higher




OK

11.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [FL SENSOR] - NO. 1 ULTRASONIC SENSOR [FR SENSOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [FL SENSOR] - NO. 1 ULTRASONIC SENSOR [FR SENSOR])
a.

Disconnect the B8 No. 1 ultrasonic sensor (FL sensor) connector.


b.

Disconnect the B7 No. 1 ultrasonic sensor (FR sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B8-2 (BO) - B7-1 (BI) Always Below 1 Ω
B8-4 (SO) - B7-3 (SI) Always Below 1 Ω
B8-6 (EO) - B7-5 (EI) Always Below 1 Ω
B8-2 (BO) - Body ground Always 10 kΩ or higher
B8-4 (SO) - Body ground Always 10 kΩ or higher
B8-6 (EO) - Body ground Always 10 kΩ or higher




OK

12.CHECK CLEARANCE WARNING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK CLEARANCE WARNING ECU ASSEMBLY
a.
U163940E02
1.531,1.938 1.844,2.5 1.844,2.5 2.052,2.5 true 1.313,1.938 1.448,2.698 1.448,2.698 1.656,2.698 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 2.083,2.406 2.479,2.552 0.396,0.146 10 false CSG1 1.688,2.604 2.083,2.771 0.396,0.167 10 false CSB1 1.583,1.188 1.906,1.406 0.323,0.219 10 false F12

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F12-21 (CSB1) - Body ground Engine switch on (IG) 7.2 to 8.8 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-19 (CSG1) - Body ground Always Below 1 Ω



Text in Illustration
*a Component with harness connected
(Clearance Warning ECU Assembly)


OK

13.CHECK FOR DTC

NG

14.REPLACE NO. 1 ULTRASONIC SENSOR (FL SENSOR)
a.

Replace the No. 1 ultrasonic sensor (FL sensor) with a normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL).



NEXT

15.CHECK FOR DTC
15.CHECK FOR DTC

OK

END (NO. 1 ULTRASONIC SENSOR [FL SENSOR] IS DEFECTIVE)

NG

16.REPLACE NO. 1 ULTRASONIC SENSOR (FR SENSOR)
16.REPLACE NO. 1 ULTRASONIC SENSOR (FR SENSOR)
a.

Replace the No. 1 ultrasonic sensor (FR sensor) with a normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL).



NEXT

17.CHECK FOR DTC
17.CHECK FOR DTC

OK

END (NO. 1 ULTRASONIC SENSOR [FR SENSOR] IS DEFECTIVE)

NG