Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255497 TOYOTA PARKING ASSIST-SENSOR SYSTEM C

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  C1AED  Rear Sensor Communication Malfunction  


DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the rear sensors and the ECU, or when there is a malfunction in a rear sensor.

DTC Code DTC Detection Condition Trouble Area
C1AED An open or short circuit in the communication line between the rear sensors and ECU or a malfunction in a rear sensor during initialization mode after the engine switch is turned on (IG).
·

No. 1 ultrasonic sensor (rear side)

·

Harness or connector

·

Parking assist ECU*1

·

Clearance warning ECU assembly*2



*1: w/ Side Monitor System

*2: w/o Side Monitor System


WIRING DIAGRAM

E240912E07
5.208,0.563 5.677,0.771 0.469,0.208 10 false CSB2 4.938,0.469 5.135,0.646 0.198,0.177 10 false 20 5.229,0.76 5.781,1.031 0.552,0.271 10 false LIN2 5.01,0.677 5.177,0.833 0.167,0.156 10 false 3 5.229,0.979 5.74,1.219 0.51,0.24 10 false CSG2 5.115,2.688 5.448,2.885 0.333,0.198 10 false F76 5.104,2.875 6.604,3.115 1.5,0.24 10 false Parking Assist ECU 4.188,0.542 4.552,0.76 0.365,0.219 10 false BI 4.198,0.74 4.646,0.979 0.448,0.24 10 false SI 4.198,0.948 4.635,1.25 0.438,0.302 10 false EI 3.323,0.958 3.719,1.177 0.396,0.219 10 false EO 3.313,0.75 3.719,0.979 0.406,0.229 10 false SO 3.323,0.552 3.75,0.771 0.427,0.219 10 false BO 3.052,1.146 3.375,1.333 0.323,0.188 10 false O9 3.052,1.281 4.615,1.719 1.563,0.438 10 false No. 1 Ultrasonic Sensor (RR Sensor) 5.01,0.865 5.177,1.021 0.167,0.156 10 false 4 4.438,0.458 4.542,0.615 0.104,0.156 10 false 1 4.438,0.667 4.542,0.823 0.104,0.156 10 false 3 4.438,0.865 4.542,1.021 0.104,0.156 10 false 5 3.146,0.885 3.25,1.042 0.104,0.156 10 false 6 3.146,0.667 3.25,0.823 0.104,0.156 10 false 4 3.146,0.49 3.25,0.646 0.104,0.156 10 false 2 2.271,0.958 2.635,1.156 0.365,0.198 10 false EI 2.26,0.76 2.708,1 0.448,0.24 10 false SI 2.26,0.552 2.677,0.792 0.417,0.24 10 false BI 1.385,0.969 1.865,1.208 0.479,0.24 10 false EO 1.385,0.75 1.865,1 0.479,0.25 10 false SO 1.385,0.563 1.927,0.802 0.542,0.24 10 false BO 1.073,1.167 1.448,1.375 0.375,0.208 10 false O10 1.073,1.292 2.646,1.74 1.573,0.448 10 false No. 1 Ultrasonic Sensor (RRC Sensor) 2.51,0.875 2.615,1.031 0.104,0.156 10 false 5 2.5,0.667 2.604,0.823 0.104,0.156 10 false 3 2.49,0.479 2.594,0.635 0.104,0.156 10 false 1 1.24,0.865 1.344,1.021 0.104,0.156 10 false 6 1.24,0.667 1.344,0.823 0.104,0.156 10 false 4 1.229,0.479 1.333,0.635 0.104,0.156 10 false 2 2.219,2 2.656,2.25 0.438,0.25 10 false EO 2.219,2.198 2.656,2.448 0.438,0.25 10 false SO 2.219,2.406 2.531,2.604 0.313,0.198 10 false BO 1.396,2.396 1.865,2.615 0.469,0.219 10 false BI 1.385,2.198 1.844,2.396 0.458,0.198 10 false SI 1.396,2.021 1.823,2.229 0.427,0.208 10 false EI 1.167,2.646 1.573,2.865 0.406,0.219 10 false O11 1.177,2.823 2.688,3.208 1.51,0.385 10 false No. 1 Ultrasonic Sensor (RLC Sensor) 2.5,1.917 2.604,2.073 0.104,0.156 10 false 6 2.5,2.125 2.604,2.281 0.104,0.156 10 false 4 2.5,2.323 2.604,2.479 0.104,0.156 10 false 2 1.229,2.333 1.406,2.552 0.177,0.219 10 false 1 1.219,2.125 1.354,2.313 0.135,0.188 10 false 3 1.219,1.938 1.354,2.156 0.135,0.219 10 false 5 3.26,2 3.438,2.156 0.177,0.156 10 false EI 3.26,2.198 3.438,2.354 0.177,0.156 10 false SI 3.26,2.406 3.438,2.563 0.177,0.156 10 false BI 3.042,2.656 3.521,2.844 0.479,0.188 10 false O12 3.042,2.823 4.604,3.271 1.563,0.448 10 false No. 1 Ultrasonic Sensor (RL Sensor) 3.094,1.917 3.198,2.073 0.104,0.156 10 false 5 3.094,2.125 3.198,2.281 0.104,0.156 10 false 3 3.094,2.323 3.198,2.479 0.104,0.156 10 false 1 0.135,0.083 2.229,0.344 2.094,0.26 12 false w/ Side Monitor System:

E240912E08
5.219,0.563 5.833,0.74 0.615,0.177 10 false CSB2 5.021,0.469 5.281,0.729 0.26,0.26 10 false 7 5.219,0.771 5.667,0.979 0.448,0.208 10 false LIN2 4.958,0.688 5.302,0.927 0.344,0.24 10 false 24 5.219,0.979 5.688,1.188 0.469,0.208 10 false CSG2 5.135,2.635 5.646,2.865 0.51,0.229 10 false F12 5.125,2.792 6.385,3.26 1.26,0.469 10 false Clearance Warning ECU Assembly 4.198,0.781 4.479,1.01 0.281,0.229 10 false SI 4.188,0.563 4.469,0.76 0.281,0.198 10 false BI 4.198,0.979 4.417,1.177 0.219,0.198 10 false EI 3.323,0.958 3.635,1.177 0.313,0.219 10 false EO 3.313,0.76 3.667,0.99 0.354,0.229 10 false SO 3.313,0.552 3.625,0.75 0.313,0.198 10 false BO 3.052,1.135 3.229,1.292 0.177,0.156 10 false O9 3.073,1.271 4.573,1.646 1.5,0.375 10 false No. 1 Ultrasonic Sensor (RR Sensor) 4.948,0.875 5.24,1.188 0.292,0.313 10 false 18 4.438,0.667 4.708,0.875 0.271,0.208 10 false 3 4.427,0.479 4.552,0.667 0.125,0.188 10 false 1 4.448,0.885 4.615,1.083 0.167,0.198 10 false 5 3.135,0.885 3.302,1.104 0.167,0.219 10 false 6 3.135,0.677 3.271,0.875 0.135,0.198 10 false 4 3.135,0.479 3.333,0.677 0.198,0.198 10 false 2 2.271,0.969 2.615,1.229 0.344,0.26 10 false EI 2.271,0.76 2.542,1 0.271,0.24 10 false SI 2.271,0.563 2.542,0.813 0.271,0.25 10 false BI 1.385,0.969 1.74,1.167 0.354,0.198 10 false EO 1.385,0.771 1.677,0.927 0.292,0.156 10 false SO 1.385,0.563 1.771,0.719 0.385,0.156 10 false BO 1.083,1.135 1.427,1.344 0.344,0.208 10 false O10 1.094,1.271 2.615,1.646 1.521,0.375 10 false No. 1 Ultrasonic Sensor (RRC Sensor) 2.51,0.875 2.646,1.063 0.135,0.188 10 false 5 2.5,0.677 2.698,0.875 0.198,0.198 10 false 3 2.49,0.469 2.667,0.677 0.177,0.208 10 false 1 1.219,0.875 1.417,1.094 0.198,0.219 10 false 6 1.219,0.677 1.396,0.927 0.177,0.25 10 false 4 1.219,0.469 1.385,0.667 0.167,0.198 10 false 2 2.198,2.01 2.573,2.26 0.375,0.25 10 false EO 2.198,2.208 2.583,2.542 0.385,0.333 10 false SO 2.198,2.417 2.49,2.625 0.292,0.208 10 false BO 1.406,2.406 1.667,2.604 0.26,0.198 10 false BI 1.396,2.219 1.75,2.458 0.354,0.24 10 false SI 1.396,2 1.625,2.219 0.229,0.219 10 false EI 1.063,2.635 1.438,2.813 0.375,0.177 10 false O11 1.052,2.802 2.552,3.156 1.5,0.354 10 false No. 1 Ultrasonic Sensor (RLC Sensor) 2.5,1.917 2.604,2.073 0.104,0.156 10 false 6 2.5,2.125 2.604,2.281 0.104,0.156 10 false 4 2.5,2.323 2.604,2.479 0.104,0.156 10 false 2 1.229,2.323 1.49,2.604 0.26,0.281 10 false 1 1.219,2.125 1.344,2.313 0.125,0.188 10 false 3 1.208,1.938 1.417,2.156 0.208,0.219 10 false 5 3.26,2 3.438,2.156 0.177,0.156 10 false EI 3.26,2.198 3.438,2.354 0.177,0.156 10 false SI 3.26,2.406 3.438,2.563 0.177,0.156 10 false BI 3.073,2.635 3.583,2.833 0.51,0.198 10 false O12 3.083,2.802 4.583,3.167 1.5,0.365 10 false No. 1 Ultrasonic Sensor (RL Sensor) 3.083,1.917 3.26,2.188 0.177,0.271 10 false 5 3.083,2.115 3.271,2.323 0.188,0.208 10 false 3 3.083,2.323 3.24,2.531 0.156,0.208 10 false 1 0.125,0.063 2.167,0.323 2.042,0.26 12 false w/o Side Monitor System:

PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1AED is output (w/ Side Monitor System) A
DTC C1AED is output (w/o Side Monitor System) B
DTC C1AED is not output C



A

2.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RR SENSOR] - PARKING ASSIST ECU)

B

16.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RR SENSOR] - CLEARANCE WARNING ECU ASSEMBLY)

C

2.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RR SENSOR] - PARKING ASSIST ECU)
a.

Disconnect the O9 No. 1 ultrasonic sensor (RR sensor) connector.


b.

Disconnect the F76 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O9-1 (BI) - F76-20 (CGB2) Always Below 1 Ω
O9-3 (SI) - F76-3 (LIN2) Always Below 1 Ω
O9-5 (EI) - F76-4 (CSG2) Always Below 1 Ω
O9-1 (BI) - Body ground Always 10 kΩ or higher
O9-3 (SI) - Body ground Always 10 kΩ or higher
O9-5 (EI) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RR SENSOR] - NO. 1 ULTRASONIC SENSOR [RRC SENSOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RR SENSOR] - NO. 1 ULTRASONIC SENSOR [RRC SENSOR])
a.

Disconnect the O9 No. 1 ultrasonic sensor (RR sensor) connector.


b.

Disconnect the O10 No. 1 ultrasonic sensor (RRC sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O9-2 (BO) - O10-1 (BI) Always Below 1 Ω
O9-4 (SO) - O10-3 (SI) Always Below 1 Ω
O9-6 (EO) - O10-5 (EI) Always Below 1 Ω
O9-2 (BO) - Body ground Always 10 kΩ or higher
O9-4 (SO) - Body ground Always 10 kΩ or higher
O9-6 (EO) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RRC SENSOR] - NO. 1 ULTRASONIC SENSOR [RLC SENSOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RRC SENSOR] - NO. 1 ULTRASONIC SENSOR [RLC SENSOR])
a.

Disconnect the O10 No. 1 ultrasonic sensor (RRC sensor) connector.


b.

Disconnect the O11 No. 1 ultrasonic sensor (RLC sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O10-2 (BO) - O11-1 (BI) Always Below 1 Ω
O10-4 (SO) - O11-3 (SI) Always Below 1 Ω
O10-6 (EO) - O11-5 (EI) Always Below 1 Ω
O10-2 (BO) - Body ground Always 10 kΩ or higher
O10-4 (SO) - Body ground Always 10 kΩ or higher
O10-6 (EO) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RLC SENSOR] - NO. 1 ULTRASONIC SENSOR [RL SENSOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RLC SENSOR] - NO. 1 ULTRASONIC SENSOR [RL SENSOR])
a.

Disconnect the O11 No. 1 ultrasonic sensor (RLC sensor) connector.


b.

Disconnect the O12 No. 1 ultrasonic sensor (RL sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-2 (BO) - O12-1 (BI) Always Below 1 Ω
O11-4 (SO) - O12-3 (SI) Always Below 1 Ω
O11-6 (EO) - O12-5 (EI) Always Below 1 Ω
O11-2 (BO) - Body ground Always 10 kΩ or higher
O11-4 (SO) - Body ground Always 10 kΩ or higher
O11-6 (EO) - Body ground Always 10 kΩ or higher




OK

6.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK PARKING ASSIST ECU
a.
U165799E02
2.573,1.75 2.708,1.167 2.708,1.167 2.906,1.167 true 2.75,1.979 2.625,2.625 2.625,2.625 2.427,2.625 true 0.156,0.104 0.438,0.344 0.281,0.24 10 false *a 1.573,1.094 1.958,1.323 0.385,0.229 10 false F76 1.969,2.542 2.396,2.75 0.427,0.208 10 false CSB2 2.969,1.083 3.417,1.344 0.448,0.26 10 false CSG2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F76-4 (CGB2) - Body ground Engine switch on (IG) 7.2 to 8.8 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-20 (CSG2) - Body ground Always Below 1 Ω



Text in Illustration
*a Component with harness connected
(Parking Assist ECU)


OK

7.CHECK FOR DTC

NG

7.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right) A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center) B
DTC C1AED is not output C



A

8.REPLACE NO. 1 ULTRASONIC SENSOR (RR SENSOR)

B

12.REPLACE NO. 1 ULTRASONIC SENSOR (RRC SENSOR)

C

8.REPLACE NO. 1 ULTRASONIC SENSOR (RR SENSOR)
a.

Replace the No. 1 ultrasonic sensor (RR sensor) with a normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL).



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right) A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center) B
DTC C1AED is not output C



A

10.REPLACE NO. 1 ULTRASONIC SENSOR (RL SENSOR)

B

12.REPLACE NO. 1 ULTRASONIC SENSOR (RRC SENSOR)

C

END (NO. 1 ULTRASONIC SENSOR [RR SENSOR] IS DEFECTIVE)

10.REPLACE NO. 1 ULTRASONIC SENSOR (RL SENSOR)
a.

Replace the No. 1 ultrasonic sensor (RL sensor) with a normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL).



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center) A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right) B
DTC C1AED is not output C



A

12.REPLACE NO. 1 ULTRASONIC SENSOR (RRC SENSOR)

B

C

END (NO. 1 ULTRASONIC SENSOR [RL SENSOR] IS DEFECTIVE)

12.REPLACE NO. 1 ULTRASONIC SENSOR (RRC SENSOR)
a.

Replace the No. 1 ultrasonic sensor (RRC sensor) with a normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL).



NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC

OK

END (NO. 1 ULTRASONIC SENSOR [RRC SENSOR] IS DEFECTIVE)

NG

14.REPLACE NO. 1 ULTRASONIC SENSOR (RLC SENSOR)
14.REPLACE NO. 1 ULTRASONIC SENSOR (RLC SENSOR)
a.

Replace the No. 1 ultrasonic sensor (RLC sensor) with a normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL).



NEXT

15.CHECK FOR DTC
15.CHECK FOR DTC

OK

END (NO. 1 ULTRASONIC SENSOR [RLC SENSOR] IS DEFECTIVE)

NG

16.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RR SENSOR] - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the O9 No. 1 ultrasonic sensor (RR sensor) connector.


b.

Disconnect the F12 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O9-1 (BI) - F12-7 (CGB2) Always Below 1 Ω
O9-3 (SI) - F12-24 (LIN2) Always Below 1 Ω
O9-5 (EI) - F12-18 (CSG2) Always Below 1 Ω
O9-1 (BI) - Body ground Always 10 kΩ or higher
O9-3 (SI) - Body ground Always 10 kΩ or higher
O9-5 (EI) - Body ground Always 10 kΩ or higher




OK

17.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RR SENSOR] - NO. 1 ULTRASONIC SENSOR [RRC SENSOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RR SENSOR] - NO. 1 ULTRASONIC SENSOR [RRC SENSOR])
a.

Disconnect the O9 No. 1 ultrasonic sensor (RR sensor) connector.


b.

Disconnect the O10 No. 1 ultrasonic sensor (RRC sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O9-2 (BO) - O10-1 (BI) Always Below 1 Ω
O9-4 (SO) - O10-3 (SI) Always Below 1 Ω
O9-6 (EO) - O10-5 (EI) Always Below 1 Ω
O9-2 (BO) - Body ground Always 10 kΩ or higher
O9-4 (SO) - Body ground Always 10 kΩ or higher
O9-6 (EO) - Body ground Always 10 kΩ or higher




OK

18.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RRC SENSOR] - NO. 1 ULTRASONIC SENSOR [RLC SENSOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RRC SENSOR] - NO. 1 ULTRASONIC SENSOR [RLC SENSOR])
a.

Disconnect the O10 No. 1 ultrasonic sensor (RRC sensor) connector.


b.

Disconnect the O11 No. 1 ultrasonic sensor (RLC sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O10-2 (BO) - O11-1 (BI) Always Below 1 Ω
O10-4 (SO) - O11-3 (SI) Always Below 1 Ω
O10-6 (EO) - O11-5 (EI) Always Below 1 Ω
O10-2 (BO) - Body ground Always 10 kΩ or higher
O10-4 (SO) - Body ground Always 10 kΩ or higher
O10-6 (EO) - Body ground Always 10 kΩ or higher




OK

19.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RLC SENSOR] - NO. 1 ULTRASONIC SENSOR [RL SENSOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RLC SENSOR] - NO. 1 ULTRASONIC SENSOR [RL SENSOR])
a.

Disconnect the O11 No. 1 ultrasonic sensor (RLC sensor) connector.


b.

Disconnect the O12 No. 1 ultrasonic sensor (RL sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-2 (BO) - O12-1 (BI) Always Below 1 Ω
O11-4 (SO) - O12-3 (SI) Always Below 1 Ω
O11-6 (EO) - O12-5 (EI) Always Below 1 Ω
O11-2 (BO) - Body ground Always 10 kΩ or higher
O11-4 (SO) - Body ground Always 10 kΩ or higher
O11-6 (EO) - Body ground Always 10 kΩ or higher




OK

20.CHECK CLEARANCE WARNING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK CLEARANCE WARNING ECU ASSEMBLY
a.
U163941E02
1.198,1.76 1.021,1.302 1.021,1.302 0.854,1.302 true 1.656,1.948 1.896,2.417 1.896,2.417 2.063,2.417 true 0.094,0.083 0.281,0.281 0.188,0.198 10 false *a 2.135,2.344 2.688,2.615 0.552,0.271 10 false CSG2 0.385,1.219 0.823,1.438 0.438,0.219 10 false CSB2 1.625,1.188 1.917,1.354 0.292,0.167 10 false F12

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F12-7 (CGB2) - Body ground Engine switch on (IG) 7.2 to 8.8 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-18 (CSG2) - Body ground Always Below 1 Ω



Text in Illustration
*a Component with harness connected
(Clearance Warning ECU Assembly)


OK

21.CHECK FOR DTC

NG

21.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right) A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center) B
DTC C1AED is not output C



A

22.REPLACE NO. 1 ULTRASONIC SENSOR (RR SENSOR)

B

26.REPLACE NO. 1 ULTRASONIC SENSOR (RRC SENSOR)

C

22.REPLACE NO. 1 ULTRASONIC SENSOR (RR SENSOR)
a.

Replace the No. 1 ultrasonic sensor (RR sensor) with a normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL).



NEXT

23.CHECK FOR DTC
23.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right) A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center) B
DTC C1AED is not output C



A

24.REPLACE NO. 1 ULTRASONIC SENSOR (RL SENSOR)

B

26.REPLACE NO. 1 ULTRASONIC SENSOR (RRC SENSOR)

C

END (NO. 1 ULTRASONIC SENSOR [RR SENSOR] IS DEFECTIVE)

24.REPLACE NO. 1 ULTRASONIC SENSOR (RL SENSOR)
a.

Replace the No. 1 ultrasonic sensor (RL sensor) with a normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL).



NEXT

25.CHECK FOR DTC
25.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center) A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right) B
DTC C1AED is not output C



A

26.REPLACE NO. 1 ULTRASONIC SENSOR (RRC SENSOR)

B

C

END (NO. 1 ULTRASONIC SENSOR [RL SENSOR] IS DEFECTIVE)

26.REPLACE NO. 1 ULTRASONIC SENSOR (RRC SENSOR)
a.

Replace the No. 1 ultrasonic sensor (RRC sensor) with a normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL).



NEXT

27.CHECK FOR DTC
27.CHECK FOR DTC

OK

END (NO. 1 ULTRASONIC SENSOR [RRC SENSOR] IS DEFECTIVE)

NG

28.REPLACE NO. 1 ULTRASONIC SENSOR (RLC SENSOR)
28.REPLACE NO. 1 ULTRASONIC SENSOR (RLC SENSOR)
a.

Replace the No. 1 ultrasonic sensor (RLC sensor) with a normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL).



NEXT

29.CHECK FOR DTC
29.CHECK FOR DTC

OK

END (NO. 1 ULTRASONIC SENSOR [RLC SENSOR] IS DEFECTIVE)

NG