Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System) › 2014.08–2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255506 PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System)  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the navigation receiver assembly receives a signal via CAN communication from the steering sensor that indicates a power supply problem.

DTC Code DTC Detection Condition Trouble Area
C1625 Open or short in steering angle sensor +B
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

E246948E02
5.717,1.928 6.971,2.289 1.254,0.361 10 Multi-media Module Receiver Assembly 3.823,1.797 4.101,1.955 0.278,0.158 10 E11 3.823,1.949 4.883,2.107 1.060,0.158 10 Steering Sensor 3.868,0.376 4.188,0.534 0.320,0.158 10 BAT 3.868,1.105 4.188,1.263 0.320,0.158 10 IG 3.868,1.488 4.188,1.646 0.320,0.158 10 ESS 3.696,0.28 3.797,0.438 0.100,0.158 10 3 3.696,1.009 3.797,1.167 0.100,0.158 10 1 3.696,1.393 3.797,1.550 0.100,0.158 10 2 3.349,0.28 3.538,0.438 0.189,0.158 10 *1 2.827,0.528 3.382,0.686 0.554,0.158 10 ECU-B1 2.654,1.233 3.553,1.391 0.899,0.158 10 ECU-IG No. 2 1.675,0.771 2.454,0.929 0.779,0.158 10 from Battery 0.753,0.386 2.446,0.544 1.692,0.158 10 from Steering Control ECU 1.053,1.102 2.448,1.260 1.395,0.158 10 from IG1 NO. 3 Relay 0.717,1.829 2.430,1.987 1.713,0.158 10 : CAN Communication Line 0.106,2.145 2.889,2.303 2.783,0.158 10 *1: w/ Variable Gear Ratio Steering System 0.106,2.419 2.889,2.576 2.783,0.158 10 *2: w/o Variable Gear Ratio Steering System 3.349,0.687 3.538,0.845 0.189,0.158 10 *2

CAUTION / NOTICE / HINT

NOTICE:
·

Since the parking assist monitor system (w/o Side Monitor System) has functions that use CAN communication system, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

·

When "System initializing" is displayed on the navigation receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System)>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system (w/o Side Monitor System) may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - BATTERY AND BODY GROUND)
a.
U166116E02
1,1.333 0.813,1.563 0.813,1.563 0.615,1.563 true 1.344,1.344 1.479,1.688 1.479,1.688 1.677,1.688 true 1.188,1.344 1.104,1.792 1.104,1.792 0.906,1.792 true 1.583,0.458 1.875,0.667 0.292,0.208 10 false E11 0.094,0.073 0.365,0.292 0.271,0.219 10 false *a 0.406,1.49 0.708,1.688 0.302,0.198 10 false IG 0.552,1.719 0.979,1.927 0.427,0.208 10 false ESS 1.729,1.615 2.135,1.823 0.406,0.208 10 false BAT

Disconnect the E11 connector from the steering sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E11-2 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E11-1 (IG) - E11-2 (ESS) Engine switch on (IG) 11 to 14 V
E11-3 (BAT) - E11-2 (ESS) Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR