This DTC is stored if the multi-media module receiver assembly judges that the signals or signal lines between the multi-media module receiver assembly and the rear television camera assembly are not normal as a result of its self check.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1622 | Open or short in the rear television camera assembly signal circuit | ·
Harness or connector ·
Rear television camera assembly ·
Multi-media module receiver assembly |
When "System initializing" is displayed on the multi-media module receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System)>INITIALIZATION).
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system (w/o Side Monitor System) may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System)>CALIBRATION).
Disconnect the F77 multi-media module receiver assembly connector.
Disconnect the S5 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F77-18 (V+) - S5-2 (CV+) | Always | Below 1 Ω |
| F77-19 (V-) - S5-1 (CV-) | Always | Below 1 Ω |
| F77-39 (CA+) - S5-4 (CB+) | Always | Below 1 Ω |
| F77-40 (CGND) - S5-3 (CGND) | Always | Below 1 Ω |
| F77-12 (GND1) - Body ground | Always | Below 1 Ω |
| F77-18 (V+) - Body ground | Always | 10 kΩ or higher |
| F77-19 (V-) - Body ground | Always | 10 kΩ or higher |
| F77-39 (CA+) - Body ground | Always | 10 kΩ or higher |
| F77-40 (CGND) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the multi-media module receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F77-40 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F77-39 (CA+) - F77-40 (CGND) | Engine switch on (IG), shift lever in R | 5.5 to 7.05 V |
| *a | Component with harness connected
(Multi-media Module Receiver Assembly) |
OK
NG
Reconnect the S5 rear television camera assembly connector.
| *a | Component with harness connected
(Multi-media Module Receiver Assembly) |
*b | Waveform A |
| *c | Waveform A | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-media module receiver assembly with the connector connected.
The video waveform changes according to the image sent by the rear television camera assembly.
| Item | Content |
|---|---|
| Tester No. (Symbol) | F77-18 (V+) - F77-40 (CGND) |
| Tool Setting | 0.2 V/DIV., 50 μS/DIV |
| Condition | Waveform A: Engine starts, shift lever in R (camera lens is not covered, displaying an image)
Waveform B: Engine starts, shift lever in R (camera lens is covered, blacking out the screen) |
Waveform is as shown in the illustration.
OK
NG