Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255515 MULTI-TERRAIN MONITOR SYSTEM C

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  C1684  Side Camera Current Malfunction  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the side television camera assembly to the parking assist ECU.

DTC Code DTC Detection Condition Trouble Area
C1684 Side Camera Current Malfunction
for LHD:
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly RH

·

Outer rear view mirror assembly RH


for RHD:
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly LH

·

Outer rear view mirror assembly LH



WIRING DIAGRAM

for LHD:

E330219E13
0.438,1.792 2.01,2.208 1.573,0.417 10 false SideTelevision Camera Assembly RH 3.115,1.771 3.563,1.938 0.448,0.167 10 false I32 3.125,1.948 4.594,2.406 1.469,0.458 10 false Outer Rear View Mirror Assembly RH 5.698,1.729 6.146,1.896 0.448,0.167 10 false F76 5.698,1.938 6.969,2.188 1.271,0.25 10 false Parking Assist ECU 3.667,0.677 4.125,0.875 0.458,0.198 10 false DCB+ 3.688,1.167 4.146,1.396 0.458,0.229 10 false DGND 4.208,0.583 4.656,0.75 0.448,0.167 10 false 2 4.188,1.052 4.635,1.219 0.448,0.167 10 false 13 5.667,0.583 6.115,0.75 0.448,0.167 10 false 31 5.667,1.073 6.115,1.24 0.448,0.167 10 false 32 5.948,0.688 6.396,0.854 0.448,0.167 10 false SCB+ 5.938,1.177 6.385,1.344 0.448,0.167 10 false SGND

for RHD:

E330219E14
0.438,1.771 1.927,2.208 1.49,0.438 10 false SideTelevision Camera Assembly LH 3,1.75 3.458,1.948 0.458,0.198 10 false I35 2.99,1.938 4.417,2.313 1.427,0.375 10 false Outer Rear View Mirror Assembly LH 5.698,1.729 6.146,1.896 0.448,0.167 10 false F76 5.698,1.917 6.958,2.156 1.26,0.24 10 false Parking Assist ECU 3.698,0.677 4.146,0.844 0.448,0.167 10 false SCB+ 3.677,1.167 4.125,1.333 0.448,0.167 10 false SGND 4.188,0.583 4.635,0.75 0.448,0.167 10 false 2 4.188,1.052 4.635,1.219 0.448,0.167 10 false 13 5.688,0.583 6.135,0.75 0.448,0.167 10 false 31 5.677,1.063 6.125,1.229 0.448,0.167 10 false 32 5.948,0.688 6.417,0.906 0.469,0.219 10 false SCB+ 5.938,1.177 6.406,1.385 0.469,0.208 10 false SGND


CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY)
a.

Disconnect the F76 parking assist ECU connector.


b.

Disconnect the I32*1 or I35 outer rear view mirror assembly connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F76-31 (SCB+) - I32-2 (DCB+) Always Below 1 Ω
F76-32 (SGND) - I32-13 (DCND) Always Below 1 Ω
F76-31 (SCB+) - Body ground Always 10 kΩ or higher
F76-32 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F76-31 (SCB+) - I35-2 (SCB+) Always Below 1 Ω
F76-32 (SGND) - I35-13 (SCND) Always Below 1 Ω
F76-31 (SCB+) - Body ground Always 10 kΩ or higher
F76-32 (SGND) - Body ground Always 10 kΩ or higher




OK

2.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU
a.
U166332E02
1.573,1.146 1.656,1.427 1.656,1.427 1.823,1.427 true 1.5,1.146 1.417,1.427 1.417,1.427 1.177,1.427 true 0.104,0.073 0.396,0.323 0.292,0.25 10 false *a 1.552,0.542 1.875,0.76 0.323,0.219 10 false F76 1.885,1.344 2.323,1.521 0.438,0.177 10 false SCB+ 0.688,1.344 1.125,1.521 0.438,0.177 10 true SGND

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-32 (SGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F76-31 (SCB+) - F76-32 (SGND) Engine switch on (IG) 5.5 to 7.05 V



Text in Illustration
*a Component with harness connected
(Parking Assist ECU)


OK

3.REPLACE SIDE TELEVISION CAMERA ASSEMBLY

NG

3.REPLACE SIDE TELEVISION CAMERA ASSEMBLY
a.

for LHD:

Replace the side television camera assembly RH with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL).


b.

for RHD:

Replace the side television camera assembly LH with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL).



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

DTC C1684 is not output.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

B

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

C

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH