DTC C1686 is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the side television camera assembly to the parking assist ECU.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1686 | Side Camera Feedback Malfunction | for LHD:
·
Harness or connector ·
Parking assist ECU ·
Side television camera assembly LH ·
Outer rear view mirror assembly LH for RHD:
·
Harness or connector ·
Parking assist ECU ·
Side television camera assembly RH ·
Outer rear view mirror assembly RH |
for LHD:
for RHD:
When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION).
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the F76 parking assist ECU connector.
Disconnect the I35*1 or I32*2 outer rear view mirror assembly connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F76-4 (DCV-) - I35-12 (SCV-) | Always | Below 1 Ω |
| F76-5 (DCV+) - I35-1 (SCV+) | Always | Below 1 Ω |
| F76-3 (DGND) - I35-13 (SGND) | Always | Below 1 Ω |
| F76-2 (DCB+) - I35-2 (SCB+) | Always | Below 1 Ω |
| F76-1 (SGND) - Body ground | Always | Below 1 Ω |
| F76-4 (DCV-) - Body ground | Always | 10 kΩ or higher |
| F76-5 (DCV+) - Body ground | Always | 10 kΩ or higher |
| F76-3 (DGND) - Body ground | Always | 10 kΩ or higher |
| F76-2 (DCB+) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F76-4 (DCV-) - I32-12 (DCV-) | Always | Below 1 Ω |
| F76-5 (DCV+) - I32-1 (DCV+) | Always | Below 1 Ω |
| F76-3 (DGND) - I32-13 (DGND) | Always | Below 1 Ω |
| F76-2 (DCB+) - I32-2 (DCB+) | Always | Below 1 Ω |
| F76-1 (SGND) - Body ground | Always | Below 1 Ω |
| F76-4 (DCV-) - Body ground | Always | 10 kΩ or higher |
| F76-5 (DCV+) - Body ground | Always | 10 kΩ or higher |
| F76-3 (DGND) - Body ground | Always | 10 kΩ or higher |
| F76-2 (DCB+) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (DGND) - Body ground | Always | Below 1 Ω |
| 4 (DCV-) - Body ground | Always | Below 1 Ω |
| *a | Component without harness connected
(Parking Assist ECU) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F76-3 (DGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F76-2 (DCB+) - F76-3 (DGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| *a | Component with harness connected
(Parking Assist ECU) |
OK
NG
Check the ware form of the side television camera assembly using an oscilloscope.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform A |
| *c | Waveform B | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | F76-5 (DCV+) - F76-3 (DGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | ·
Waveform A: Engine switch on (IG), main switch assembly (multi-terrain monitor main switch) on and camera lens is not covered, displaying an image ·
Waveform B: Engine switch on (IG), main switch assembly (multi-terrain monitor main switch) on and camera lens is covered, blacking out the screen |
Waveform is as shown in the illustration.
OK
NG
for LHD:
Replace the side television camera assembly LH with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL).
for RHD:
Replace the side television camera assembly RH with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL).
NEXT
Clear the DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR).
DTC C1686 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C