Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255516 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH judges that there is a communication error with the blind spot monitor sensor RH.

DTC No. DTC Detection Condition Trouble Area
U0232 The blind spot monitor sensor LH cannot receive signals from the blind spot monitor sensor RH.
·

CAN communication Line

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E233765E79
3.063,1.24 3.479,1.469 0.417,0.229 10 false BRB 2.844,1.115 3.01,1.313 0.167,0.198 10 false 5 2.813,2.51 2.99,2.688 0.177,0.177 10 false 10 3.063,2.615 3.49,2.771 0.427,0.156 10 false BRGD 1.615,1.385 2.74,1.563 1.125,0.177 10 false ECU-IG NO. 3 0.104,1.219 1.156,1.75 1.052,0.531 10 false from IG1 NO. 2 Relay 3.031,3.229 3.396,3.385 0.365,0.156 10 false r1 3.031,3.406 4.229,3.844 1.198,0.438 10 false Blind Spot Monitor Sensor RH 5.375,3.219 5.74,3.375 0.365,0.156 10 false r2 5.385,3.406 6.604,3.854 1.219,0.448 10 false Blind Spot Monitor Sensor LH 3.531,1.594 3.99,1.813 0.458,0.219 10 false CA2P 3.531,1.938 3.948,2.156 0.417,0.219 10 false CA2N 4.01,1.781 4.198,1.979 0.188,0.198 10 false 6 4.01,1.448 4.198,1.646 0.188,0.198 10 false 1 5.188,1.448 5.302,1.625 0.115,0.177 10 false 1 5.198,1.781 5.313,1.958 0.115,0.177 10 false 6 5.385,1.583 5.854,1.792 0.469,0.208 10 false CA2P 5.385,1.938 5.844,2.188 0.458,0.25 10 false CA2N 0.844,4.021 2.802,4.292 1.958,0.271 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor main switch (steering pad switch assembly [multi-function switch]) is on.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the r1 blind spot monitor sensor RH connector.


b.

Disconnect the r2 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r1-1 (CA2P) - r2-1 (CA2P) Always Below 1 Ω
r1-6 (CA2N) - r2-6 (CA2N) Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN LINE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BATTERY AND BODY GROUND)
a.
U166397E01
1.642,0.278 1.919,0.479 0.276,0.201 10 r1 2.646,1.719 3.064,1.871 0.418,0.152 10 BRGD 2.663,0.615 3.081,0.767 0.418,0.152 10 BRB 0.104,0.08 0.380,0.281 0.276,0.201 10 *a 2.042,1.148 2.357,0.69 2.357,0.69 2.63,0.69 false 2.033,1.37 2.386,1.812 2.386,1.812 2.624,1.812 false

Disconnect the r1 blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r1-10 (BRGD) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
r1-5 (BRB) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


OK

3.REPLACE BLIND SPOT MONITOR SENSOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE BLIND SPOT MONITOR SENSOR RH
a.


NEXT

4.RECHECK DTC
4.RECHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

END (BLIND SPOT MONITOR SENSOR RH WAS DEFECTIVE)

NG