Home › Power Source / Network › 1VD-FTV (BATTERY / CHARGING) › GENERATOR
RM2660E _57 Power Source / Network _052833 1VD-FTV BATTERY / CHARGING _0255523 GENERATOR G

1VD-FTV BATTERY / CHARGING  GENERATOR  INSPECTION  


PROCEDURE

Hide 27310B 1.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A163021

Rotate the bearing and check that there is no abnormal noise and that it rotates smoothly.

If necessary, replace the bearing (See page Power Source / Network>1VD-FTV (BATTERY / CHARGING)>GENERATOR>DISASSEMBLY).


Hide 27330 2.INSPECT GENERATOR ROTOR ASSEMBLY

a.
A178037E01
0.059,0 1.860,0.187 1.801,0.187 10 130 A Type and 150 A Type: 0.059,2.465 0.851,2.651 0.792,0.186 10 180 A Type:

Check the rotor for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
130 A Type
Tester Connection Condition Specified Condition
Slip ring - Slip ring 20°C (68°F) 2.3 to 2.7 Ω

150 A Type
Tester Connection Condition Specified Condition
Slip ring - Slip ring 20°C (68°F) 1.5 to 1.9 Ω

180 A Type
Tester Connection Condition Specified Condition
Slip ring - Slip ring 20°C (68°F) 1.36 to 1.76 Ω


If the result is not as specified, replace the rotor assembly.



b.
A178038E01
0.056,0 1.866,0.212 1.810,0.212 10 130 A Type and 150 A Type: 0.056,2.378 0.873,2.582 0.817,0.204 10 180 A Type:

Check if the rotor is grounded.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Slip ring - Rotor Always 10 kΩ or higher


If the result is not as specified, replace the rotor assembly.



c.

Check that the slip rings are not rough or scored.

If rough or scored, replace the rotor assembly.


d.
A178039E01
0.302,2.78 0.935,2.964 0.633,0.184 10 Diameter 0.314,0.55 0.946,0.733 0.633,0.184 10 Diameter 0.037,0 1.831,0.193 1.795,0.193 10 130 A Type and 150 A Type: 0.037,2.213 0.845,2.397 0.809,0.184 10 180 A Type:

Using a vernier caliper, measure the slip ring diameter.

Standard diameter:

14.2 to 14.4 mm (0.559 to 0.567 in.)


Minimum diameter:

14.0 mm (0.551 in.)


If the diameter is less than the minimum, replace the rotor assembly.


Hide 3.INSPECT GENERATOR ROTOR BEARING

a.
A178042E01
0.056,0 1.871,0.198 1.815,0.198 10 130 A Type and 150 A Type: 0.056,2.376 0.878,2.560 0.823,0.184 10 180 A Type:

Rotate the bearing and check that there is no abnormal noise and that it rotates smoothly.

If necessary, replace the generator rotor.


Hide 27370 4.INSPECT GENERATOR BRUSH HOLDER ASSEMBLY

a.
A163020E01
0.787,0.391 1.251,0.573 0.464,0.182 10 Length

Using a vernier caliper, measure the exposed brush length.

Standard exposed length:

10.5 mm (0.413 in.)


Minimum exposed length:

4.5 mm (0.177 in.)


If the exposed length is less than the minimum, replace the brush holder assembly.