Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item DTC Detection Condition Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on the "Bus Check" screen.

·

"Skid Control ECU Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of master cylinder solenoid (skid control ECU)

·

Master cylinder solenoid (skid control ECU) CAN branch wire or connector

·

Master cylinder solenoid (skid control ECU)



For vehicles without a vehicle stability control system.


WIRING DIAGRAM

E207356E02
5.813,0.589 6.224,0.770 0.411,0.181 10 CANH 5.536,0.514 5.707,0.695 0.171,0.181 10 11 5.536,0.957 5.707,1.138 0.171,0.181 10 25 1.918,0.514 2.074,0.695 0.156,0.181 10 5 1.949,0.957 2.121,1.138 0.171,0.181 10 16 0.569,1.433 0.833,1.615 0.264,0.181 10 E75 0.569,1.601 2.155,1.783 1.586,0.181 10 No. 3 Junction Connector 5.385,3.4 5.649,3.582 0.264,0.181 10 A24 5.813,1.031 6.201,1.212 0.387,0.181 10 CANL 5.536,2.99 5.707,3.171 0.171,0.181 10 32 5.813,3.063 6.216,3.245 0.403,0.181 10 GND2 5.574,2.536 5.730,2.718 0.156,0.181 10 1 5.813,2.61 6.216,2.791 0.403,0.181 10 GND1 5.535,2.073 5.706,2.254 0.171,0.181 10 46 5.813,2.147 6.054,2.328 0.241,0.181 10 IG1 3.436,2.003 4.573,2.184 1.138,0.181 10 ECU-IG No. 2 1.274,2.147 2.734,2.328 1.460,0.181 10 from IG1 NO. 3 Relay 5.384,3.571 6.981,4.035 1.597,0.463 10 Master Cylinder Solenoid (Skid Control ECU)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
U166121E01
0.087,0.075 0.315,0.262 0.229,0.187 10 *a 2.527,1.756 2.920,1.894 0.393,0.138 10 CANL 2.734,0.682 3.148,0.820 0.414,0.138 10 CANH 2.042,1.214 2.595,0.761 2.595,0.761 2.715,0.761 false 2.042,1.33 2.36,1.827 2.36,1.827 2.5,1.827 false 0.272,1.263 0.537,1.408 0.264,0.145 10 A24

Disconnect the A24 master cylinder solenoid (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A24-11 (CANH) - A24-25 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SKID CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U166122E01
0.087,0.075 0.315,0.262 0.229,0.187 10 *a 2.854,1.717 3.112,1.855 0.258,0.138 10 IG1 0.276,1.766 0.690,1.904 0.414,0.138 10 GND2 0.109,0.765 0.523,0.903 0.414,0.138 10 GND1 1.029,1.231 0.74,0.844 0.74,0.844 0.62,0.844 false 1.189,1.47 0.9,1.857 0.9,1.857 0.781,1.857 false 2.458,1.527 2.686,1.788 2.686,1.788 2.827,1.788 false 0.272,1.263 0.537,1.408 0.264,0.145 10 A24

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A24-46 (IG1) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-1 (GND1) - Body ground Always Below 1 Ω
A24-32 (GND2) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])


OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR