Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Gateway ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Gateway ECU Communication Stop Mode Either condition is met:
·

"CAN Gateway" is not displayed on the "Bus Check" screen.

·

"Gateway ECU Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of network gateway ECU

·

Network gateway ECU CAN branch wire or connector

·

Network gateway ECU



For vehicles with a network gateway ECU.


WIRING DIAGRAM

C174518E18
0.76,1.458 1.24,1.656 0.479,0.198 10 false E69 0.76,1.625 2.5,1.865 1.74,0.24 10 false No. 2 Junction Connector 2.938,1.958 3.865,2.219 0.927,0.26 10 false from Battery 2.385,2.417 3.865,2.677 1.479,0.26 10 false from IG1 NO. 1 Relay 5.594,0.604 6.073,0.802 0.479,0.198 10 false CA1H 5.344,0.49 5.521,0.656 0.177,0.167 10 false 16 5.594,1.052 6.073,1.25 0.479,0.198 10 false CA1L 5.344,0.938 5.521,1.104 0.177,0.167 10 false 15 1.708,0.469 1.885,0.635 0.177,0.167 10 false 3 1.708,0.917 1.885,1.083 0.177,0.167 10 false 14 5.594,1.958 6.073,2.156 0.479,0.198 10 false BATT 4.427,1.76 4.979,1.958 0.552,0.198 10 false ECU-B1 4.281,2.24 5.198,2.438 0.917,0.198 10 false ECU-IG No. 1 5.396,1.844 5.542,2.01 0.146,0.167 10 false 2 5.594,2.427 6.073,2.625 0.479,0.198 10 false IG1 5.198,3.688 5.521,3.885 0.323,0.198 10 false E31 5.198,3.865 6.677,4.063 1.479,0.198 10 false Network Gateway ECU 5.333,2.302 5.521,2.469 0.188,0.167 10 false 10 2.771,2.854 3.865,3.063 1.094,0.208 10 false from IG2 Relay 4.583,2.677 4.885,2.875 0.302,0.198 10 false IGN 5.594,2.844 6.073,3.042 0.479,0.198 10 false IG2 5.396,2.729 5.542,2.896 0.146,0.167 10 false 9 5.594,3.271 6.073,3.469 0.479,0.198 10 false GND 5.396,3.156 5.542,3.323 0.146,0.167 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE)
a.
U165156E01
2.758,1.136 3.032,1.273 0.273,0.137 10 E31 1.244,1.295 1.046,1.491 1.046,1.491 0.922,1.491 false 1.109,1.777 1.255,1.777 1.255,1.777 1.352,1.293 false 0.433,1.416 0.822,1.554 0.389,0.137 10 CA1H 0.659,1.691 1.048,1.829 0.389,0.137 10 CA1L 0.07,0.056 0.371,0.193 0.301,0.137 10 *a

Disconnect the E31 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E31-16 (CA1H) - E31-15 (CA1L) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)



OK

4.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE NETWORK GATEWAY ECU BRANCH WIRE OR CONNECTOR (CA1H, CA1L)

4.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)
a.
U165157E01
0.455,1.136 0.728,1.273 0.273,0.137 10 E31 2.273,1.122 2.561,0.778 2.561,0.778 2.684,0.778 false 1.351,1.122 1.005,0.73 1.005,0.73 0.882,0.73 false 2.708,0.696 3.084,0.833 0.376,0.137 10 BATT 0.449,0.649 0.825,0.786 0.376,0.137 10 GND 0.07,0.056 0.371,0.193 0.301,0.137 10 *a 2.039,1.293 2.463,1.64 2.463,1.64 2.601,1.64 false 2.242,1.98 2.122,1.98 2.122,1.98 1.931,1.292 false 0.07,0.056 0.371,0.193 0.301,0.137 10 *a 2.613,1.56 2.900,1.698 0.287,0.137 10 IG2 2.266,1.895 2.804,2.032 0.538,0.137 10 IG1

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E31-4 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E31-2 (BATT) - Body ground Always 11 to 14 V
E31-10 (IG1) - Body ground Ignition switch ON 11 to 14 V
E31-9 (IG2) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR