Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U0126  Lost Communication with Steering Angle Sensor Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0126 There is no communication from the steering angle sensor.
·

Power source circuit of steering angle sensor

·

Steering angle sensor branch wire or connector

·

Steering angle sensor



For vehicles with a vehicle stability control system.


WIRING DIAGRAM

C164886E13
5.812,1.943 6.306,2.117 0.493,0.174 10 CANH 5.812,2.38 6.283,2.545 0.471,0.165 10 CANL 5.812,3.878 6.089,4.073 0.277,0.195 10 IG 5.812,3.052 6.103,3.263 0.291,0.211 10 BAT 5.812,4.68 6.212,4.857 0.400,0.177 10 ESS 1.92,1.852 2.111,2.014 0.191,0.163 10 4 1.92,2.306 2.125,2.450 0.205,0.145 10 15 0.641,2.714 0.944,2.875 0.302,0.161 10 E74 0.641,2.871 2.254,3.049 1.612,0.178 10 No. 7 Junction Connector 0.144,0.057 4.203,0.235 4.059,0.178 12 w/ Variable Gear Ratio Steering System: 3.825,3.73 4.714,3.870 0.889,0.140 10 ECU-IG No. 2 3.389,5.229 3.968,5.746 0.578,0.517 10 from IG1 NO. 3 Relay 5.514,5.335 5.853,5.514 0.339,0.179 10 E11 5.558,1.846 5.777,2.020 0.220,0.173 10 10 5.601,2.294 5.812,2.462 0.211,0.169 10 9 5.601,3.796 5.813,3.944 0.213,0.148 10 1 5.601,2.972 5.812,3.133 0.212,0.161 10 3 5.601,4.578 5.774,4.754 0.174,0.176 10 2 5.514,5.51 6.995,5.689 1.481,0.179 10 Steering Angle Sensor 2.31,5.242 3.223,5.629 0.912,0.387 10 from Steering Control ECU

C358108E01
0.51,2.51 2.333,2.885 1.823,0.375 10 false No. 7 Junction Connector 0.51,2.323 1.208,2.51 0.698,0.188 10 false E74 5.406,4.917 6.104,5.104 0.698,0.188 10 false E11 5.406,5.115 7.042,5.51 1.635,0.396 10 false Steering Angle Sensor 2.125,4.792 3.073,5.25 0.948,0.458 10 false from Battery 3.125,4.813 3.771,5.771 0.646,0.958 10 false from IG1 NO. 3 Relay 3.667,3.198 4.677,3.521 1.01,0.323 10 false ECU-IG No. 2 3.625,2.375 4.375,2.719 0.75,0.344 10 false ECU-B1 5.615,1.448 6.229,1.646 0.615,0.198 10 false CANH 5.333,1.333 5.646,1.531 0.313,0.198 10 false 10 1.719,1.333 2.031,1.531 0.313,0.198 10 false 4 1.708,1.781 2.021,1.979 0.313,0.198 10 false 15 5.396,1.771 5.708,1.969 0.313,0.198 10 false 9 5.396,2.438 5.708,2.635 0.313,0.198 10 false 3 5.396,3.26 5.708,3.458 0.313,0.198 10 false 1 5.396,4.073 5.708,4.271 0.313,0.198 10 false 2 5.625,1.885 6.24,2.083 0.615,0.198 10 false CANL 5.635,2.552 6.25,2.75 0.615,0.198 10 false BAT 5.625,3.385 6.24,3.583 0.615,0.198 10 false IG 5.604,4.177 6.219,4.375 0.615,0.198 10 false ESS 0.188,0.146 3.844,0.656 3.656,0.51 12 false w/o Variable Gear Ratio Steering System:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.
U165159E01
1.172,1.309 0.944,1.537 0.944,1.537 0.834,1.537 false 1.008,1.802 1.068,1.802 1.068,1.802 1.307,1.309 false 0.338,1.451 0.759,1.594 0.421,0.143 10 CANH 1.613,0.371 1.880,0.514 0.266,0.143 10 E11 0.51,1.72 0.931,1.863 0.421,0.143 10 CANL 0.058,0.035 0.253,0.178 0.195,0.143 10 *a

Disconnect the E11 steering angle sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E11-10 (CANH) - E11-9 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Steering Angle Sensor)



OK

4.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE STEERING ANGLE SENSOR CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)
a.
U165160E01
2.213,1.309 2.441,1.537 2.441,1.537 2.551,1.537 false 2.376,1.802 2.316,1.802 2.316,1.802 2.078,1.309 false 2.59,1.451 3.011,1.594 0.421,0.143 10 ESS 2.673,0.987 3.094,1.130 0.421,0.143 10 IG 1.621,0.368 1.885,0.511 0.264,0.143 10 E11 2.401,1.72 2.821,1.863 0.421,0.143 10 BAT 0.058,0.035 0.253,0.178 0.195,0.143 10 *a 2.348,1.23 2.545,1.062 2.545,1.062 2.651,1.062 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E11-3 (BAT) - Body ground Always 11 to 14 V
E11-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E11-2 (ESS) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Steering Angle Sensor)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR