Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U0131  Lost Communication with Power Steering Control Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0131 There is no communication from the power steering ECU assembly.
·

Power source circuit of power steering ECU assembly

·

Power steering ECU assembly CAN branch wire or connector

·

Power steering ECU assembly



For vehicles for 1VD-FTV with DPF.


WIRING DIAGRAM

C173460E05
5.677,1.208 6.125,1.385 0.448,0.177 10 false CANH 5.479,1.125 5.677,1.302 0.198,0.177 10 false 1 5.677,1.646 6.125,1.823 0.448,0.177 10 false CANL 5.479,1.552 5.646,1.76 0.167,0.208 10 false 2 1.781,1.125 1.906,1.302 0.125,0.177 10 false 4 1.781,1.573 1.979,1.75 0.198,0.177 10 false 15 5.677,3 6.125,3.177 0.448,0.177 10 false B 3.729,2.823 4.719,3.052 0.99,0.229 10 false ECU-IG No. 2 2.688,4.385 4.167,4.677 1.479,0.292 10 false from IG1 NO. 3 Relay 0.5,2.198 2.24,2.656 1.74,0.458 10 false No. 4 Junction Connector 0.5,2.031 0.813,2.208 0.313,0.177 10 false E71 5.479,2.906 5.635,3.083 0.156,0.177 10 false 5 5.677,3.792 6.125,3.969 0.448,0.177 10 false GND 5.417,4.583 5.823,4.792 0.406,0.208 10 false E102 5.417,4.771 6.792,5.406 1.375,0.635 10 false Power Steering ECU Assembly 5.469,3.708 5.646,3.875 0.177,0.167 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)
a.
U166188E01
0.079,0 0.319,0.218 0.239,0.218 10 *a 1.603,1.622 2.050,1.827 0.448,0.205 10 CANL 0.357,1.609 0.804,1.814 0.448,0.205 10 CANH 1.576,0.311 1.918,0.452 0.342,0.140 10 E102 1.306,1.364 1.482,1.695 1.482,1.695 1.573,1.695 false 1.134,1.364 0.958,1.695 0.958,1.695 0.868,1.695 false

Disconnect the E102 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E102-1 (CANH) - E102-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU assembly)



OK

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE POWER STEERING ECU ASSEMBLY BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166189E01
1.576,0.311 1.918,0.452 0.342,0.140 10 E102 0.079,0 0.319,0.218 0.239,0.218 10 *a 2.105,1.622 2.553,1.827 0.448,0.205 10 IG 0.786,1.609 1.234,1.814 0.448,0.205 10 GND 1.809,1.364 1.985,1.695 1.985,1.695 2.075,1.695 false 1.482,1.364 1.306,1.695 1.306,1.695 1.216,1.695 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E102-5 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E102-3 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR