Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U0230  Lost Communication with Rear Gate Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0230 There is no communication from the power back door unit assembly (power back door ECU).
·

Power source circuit of power back door (power back door ECU)

·

Power back door unit (power back door ECU) CAN branch wire or connector

·

Power back door unit (power back door ECU)



For vehicles with a power back door system.


WIRING DIAGRAM

C358109E01
0.406,2.438 2.542,2.885 2.135,0.448 10 false No. 2 CAN Junction Connector 0.406,2.271 1.021,2.5 0.615,0.229 10 false L54 4.969,5.042 7.115,5.719 2.146,0.677 10 false Power Back Door Unit Assembly (Power Back Door ECU) 4.969,4.854 5.708,5.063 0.74,0.208 10 false L52 2.188,4.833 2.802,5.635 0.615,0.802 10 false from Battery 3.823,2.76 4.594,3 0.771,0.24 10 false ECU-B2 5.635,1.385 6.25,1.583 0.615,0.198 10 false MPX1 5.635,1.833 6.25,2.031 0.615,0.198 10 false MPX2 5.635,2.896 6.25,3.094 0.615,0.198 10 false ECUB 5.635,4.135 6.25,4.333 0.615,0.198 10 false GND 5.333,4 5.646,4.198 0.313,0.198 10 false 11 5.333,2.802 5.646,3 0.313,0.198 10 false 10 5.396,1.719 5.708,1.917 0.313,0.198 10 false 5 5.396,1.302 5.708,1.5 0.313,0.198 10 false 6 1.719,1.292 2.031,1.49 0.313,0.198 10 false 1 1.719,1.729 2.031,1.927 0.313,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any other switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (POWER BACK DOOR ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (POWER BACK DOOR ECU CAN BRANCH WIRE)
a.
U165217E01
0.373,1.009 0.623,1.150 0.250,0.141 10 L52 0.039,0.039 0.311,0.179 0.273,0.141 10 *a 2.417,1.436 2.838,1.577 0.421,0.141 10 MPX2 1.845,1.091 2.267,1.513 2.267,1.513 2.391,1.513 false 2.14,1.759 2.561,1.900 0.421,0.141 10 MPX1 1.762,1.091 1.989,1.836 1.989,1.836 2.114,1.836 false

Disconnect the L52 power back door unit assembly (power back door ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L52-6 (MPX1) - L52-5 (MPX2) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])



OK

4.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE POWER BACK DOOR ECU CAN BRANCH WIRE OR CONNECTOR (MPX1, MPX2)

4.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR ECU - BATTERY AND BODY GROUND)
a.
U165218E01
2.785,1.049 3.035,1.190 0.250,0.141 10 L52 0.039,0.039 0.311,0.179 0.273,0.141 10 *a 0.283,1.413 0.704,1.554 0.421,0.141 10 GND 1.257,1.071 0.835,1.493 0.835,1.493 0.711,1.493 false 0.541,1.736 0.962,1.877 0.421,0.141 10 ECUB 1.409,1.071 1.181,1.816 1.181,1.816 1.057,1.816 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-11 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L52-10 (ECUB) - Body ground Always 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])


OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR