Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U1111  Lost Communication with Body No. 5 Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U1111 There is no communication from the windshield wiper ECU.
·

Power source circuit of windshield wiper ECU

·

Windshield wiper ECU CAN branch wire or connector

·

Windshield wiper ECU



For vehicles with the rain sensor.


WIRING DIAGRAM

C150448E14
5.573,1.688 6.01,1.885 0.438,0.198 10 false CANL 5.573,1.24 6.063,1.448 0.49,0.208 10 false CANH 5.573,3.385 6.063,3.563 0.49,0.177 10 false E 0.469,2.052 0.823,2.25 0.354,0.198 10 false E73 0.469,2.24 2.25,2.49 1.781,0.25 10 false No. 9 Junction Connector 1.719,1.156 1.906,1.323 0.188,0.167 10 false 4 1.698,1.594 1.906,1.74 0.208,0.146 10 false 15 3.583,2.396 4.656,2.573 1.073,0.177 10 false ECU-IG No. 1 1.813,4.531 3.396,4.75 1.583,0.219 10 false from IG1 NO. 1 Relay 5.354,1.073 5.458,1.25 0.104,0.177 10 false 6 5.354,1.521 5.479,1.688 0.125,0.167 10 false 5 5.302,3.208 5.49,3.365 0.188,0.156 10 false 10 5.344,2.365 5.458,2.542 0.115,0.177 10 false 5 5.25,4.073 6.885,4.313 1.635,0.24 10 false Windshield Wiper ECU 5.26,3.396 5.615,3.615 0.354,0.219 10 false E85 5.26,2.552 5.615,2.729 0.354,0.177 10 false E83 5.26,1.708 5.604,1.906 0.344,0.198 10 false E85 5.26,1.26 5.625,1.438 0.365,0.177 10 false E85 5.573,2.531 5.948,2.729 0.375,0.198 10 false IG1I

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (WINDSHIELD WIPER ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (WINDSHIELD WIPER ECU CAN BRANCH WIRE)
a.
U166117E01
0.602,1.193 0.867,1.330 0.265,0.137 10 E85 0.091,0.062 0.260,0.223 0.170,0.161 10 *a 2.51,0.856 2.932,1.001 0.422,0.145 10 CANH 2.456,1.505 2.877,1.649 0.422,0.145 10 CANL 2.104,1.111 2.359,0.918 2.359,0.918 2.474,0.918 false 1.981,1.22 2.311,1.589 2.311,1.589 2.431,1.589 false

Disconnect the E85 windshield wiper ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E85-6 (CANH) - E85-5 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Windshield Wiper ECU)



OK

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE WINDSHIELD WIPER ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER ECU - BATTERY AND BODY GROUND)
a.
U166118E01
0.487,0.79 0.753,0.928 0.267,0.138 10 E83 0.085,0.053 0.255,0.213 0.170,0.161 10 *a 0.49,1.286 0.779,1.431 0.289,0.145 10 IG1I 2.215,3.022 2.337,3.167 0.122,0.145 10 E 0.507,2.519 0.774,2.657 0.267,0.138 10 E85 1.2,1.069 0.999,1.363 0.999,1.363 0.85,1.363 false 1.793,2.753 2.05,3.108 2.05,3.108 2.198,3.108 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the E83 windshield wiper ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E83-5 (IG1I) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E85-10 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Windshield Wiper ECU)


OK

REPLACE WINDSHIELD WIPER ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR