Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255533 CAN COMMUNICATION SYSTEM(for LHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  U0125  Lost Communication with Yaw Rate Sensor Module  U0124  Lost Communication with Lateral Acceleration Sensor Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0125 There is no communication from the yaw rate sensor assembly.
·

Power source circuit of yaw rate sensor assembly

·

Yaw rate sensor assembly CAN branch wire or connector

·

Yaw rate sensor assembly


U0124 There is no communication from the yaw rate sensor assembly (lateral acceleration sensor).
·

Power source circuit of yaw rate sensor assembly

·

Yaw rate sensor assembly CAN branch wire or connector

·

Yaw rate sensor assembly



For vehicles with a vehicle stability control system.


WIRING DIAGRAM

C358107E01
2.208,2.313 3.833,2.719 1.625,0.406 10 false from IG1 NO. 3 Relay 0.583,1.729 2.281,2.135 1.698,0.406 10 false No. 5 Junction Connector 0.583,1.552 1.198,1.792 0.615,0.24 10 false E68 5.604,3.729 6.854,4.135 1.25,0.406 10 false Yaw Rate Sensor 5.604,3.542 6.156,3.74 0.552,0.198 10 false E50 5.76,0.708 6.375,0.906 0.615,0.198 10 false CANH 1.865,1.031 2.177,1.229 0.313,0.198 10 false 14 1.865,0.583 2.177,0.781 0.313,0.198 10 false 3 5.542,0.594 5.854,0.792 0.313,0.198 10 false 3 5.542,1.031 5.854,1.229 0.313,0.198 10 false 2 5.542,2.208 5.854,2.406 0.313,0.198 10 false 4 5.542,2.719 5.854,2.917 0.313,0.198 10 false 1 4.51,2.063 5.531,2.406 1.021,0.344 10 false ECU-IG No. 2 5.75,1.146 6.365,1.344 0.615,0.198 10 false CANL 5.76,2.323 6.375,2.521 0.615,0.198 10 false IG 5.76,2.854 6.375,3.052 0.615,0.198 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U165084E01
0.602,1.615 1.001,1.759 0.399,0.143 10 CANL 0.087,0.057 0.300,0.235 0.213,0.178 10 *a 2.1,1.622 2.517,1.768 0.416,0.146 10 CANH 1.646,1.21 1.922,1.703 1.922,1.703 2.066,1.703 false 1.499,1.21 1.223,1.703 1.223,1.703 1.079,1.703 false 0.428,1.09 0.701,1.231 0.273,0.141 10 E50

Disconnect the E50 yaw rate sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E50-3 (CANH) - E50-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (YAW RATE SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (YAW RATE SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165085E01
0.501,1.615 0.827,1.759 0.326,0.143 10 GND 0.087,0.057 0.300,0.235 0.213,0.178 10 *a 2.259,1.633 2.432,1.779 0.173,0.146 10 IG 1.805,1.21 2.081,1.703 2.081,1.703 2.225,1.703 false 1.352,1.21 1.077,1.703 1.077,1.703 0.933,1.703 false 0.428,1.09 0.701,1.231 0.273,0.141 10 E50

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E50-4 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E50-1 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR