| Detection Item | Symptom | Trouble Area |
|---|---|---|
| Air Conditioning Amplifier Communication Stop Mode | Either condition is met:
·
"Air Conditioning Amplifier" is not displayed on "Bus Check". ·
"Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" applies. |
·
Power source or inside air conditioning amplifier assembly ·
Air conditioning amplifier assembly ·
Air conditioning amplifier assembly CAN branch wire or connector |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
NEXT
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
For vehicle with an SRS system:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
NEXT
Disconnect the E35*1 or E81*2 air conditioning amplifier assembly connector.
*1: w/ Rear Air Conditioning System
*2: w/o Rear Air Conditioning System
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E35-3 (CANH) - E35-4 (CANL) | Ignition switch off | 54 to 69 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E81-11 (CANH) - E81-12 (CANL) | Ignition switch off | 54 to 69 Ω |
| *A | w/ Rear Air Conditioning System |
| *B | w/o Rear Air Conditioning System |
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
OK
NG
Connect the cable to the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the E36*1 or E81*2 air conditioning amplifier assembly connector.
*1: w/ Rear Air Conditioning System
*2: w/o Rear Air Conditioning System
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E36-1 (GND) - Body ground | Always | Below 1 Ω |
| E36-2 (E1) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E81-14 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E36-6 (+B1) - Body ground | Always | 11 to 14 V |
| E36-7 (+B2) - Body ground | Always | 11 to 14 V |
| E36-5 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E81-21 (+B1) - Body ground | Always | 11 to 14 V |
| E81-1 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | w/ Rear Air Conditioning System |
| *B | w/o Rear Air Conditioning System |
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
OK
NG