Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255534 CAN COMMUNICATION SYSTEM(for RHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  U1100  Lost Communication with Seat Belt Control ECU  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U1100 There is no communication from the seat belt control ECU.
·

Power source circuit of seat belt control ECU

·

Seat belt control ECU CAN branch wire or connector

·

Seat belt control ECU



For vehicles with an pre-crash safety system.


WIRING DIAGRAM

C150433E15
4.927,5.063 4.927,5.094 false 5.813,1.938 6.302,2.115 0.49,0.177 10 false CANH 5.813,2.385 6.281,2.552 0.469,0.167 10 false CANL 5.813,4.438 6.292,4.615 0.479,0.177 10 false PGND 1.927,1.854 2.115,2.021 0.188,0.167 10 false 2 1.927,2.302 2.135,2.448 0.208,0.146 10 false 13 4.094,3.729 5.125,3.958 1.031,0.229 10 false ECU-IG No. 1 2.521,5.125 3.115,5.667 0.594,0.542 10 false from Battery 5.521,1.76 5.74,1.938 0.219,0.177 10 false 1 5.521,2.208 5.729,2.375 0.208,0.167 10 false 2 5.521,2.917 5.698,3.094 0.177,0.177 10 false 7 5.521,3.677 5.698,3.854 0.177,0.177 10 false 8 3.354,5.125 4.146,5.781 0.792,0.656 10 false from IG1 NO. 1 Relay 5.458,2.406 5.76,2.573 0.302,0.167 10 false E42 5.458,1.969 5.76,2.135 0.302,0.167 10 false E42 0.688,2.802 1.104,2.979 0.417,0.177 10 false E71 0.688,2.99 2.552,3.344 1.865,0.354 10 false No. 7 Junction Connector 5.458,4.458 5.76,4.625 0.302,0.167 10 false E41 4.385,2.958 5,3.177 0.615,0.219 10 false PSB 5.458,5.438 7.042,5.75 1.583,0.313 10 false Seat Belt Control ECU 5.458,3.125 5.76,3.292 0.302,0.167 10 false E41 5.458,3.885 5.76,4.052 0.302,0.167 10 false E42 5.521,4.271 5.698,4.448 0.177,0.177 10 false 8 5.813,3.875 6.281,4.042 0.469,0.167 10 false IG1 5.813,3.104 6.281,3.271 0.469,0.167 10 false +B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (SEAT BELT CONTROL ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (SEAT BELT CONTROL ECU CAN BRANCH WIRE)
a.
U165212E01
2.684,2.348 2.827,2.167 2.827,2.167 2.91,2.167 false 2.561,2.348 2.822,2.691 2.822,2.691 2.945,2.691 false 1.662,2.317 1.931,2.457 0.269,0.140 10 E42 0.077,0.061 0.356,0.201 0.279,0.140 10 *a 2.959,2.611 3.353,2.750 0.394,0.140 10 CANL 2.922,2.089 3.344,2.229 0.422,0.140 10 CANH

Disconnect the E42 seat belt control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E42-1 (CANH) - E42-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Seat Belt Control ECU)



OK

4.CHECK HARNESS AND CONNECTOR (SEAT BELT CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SEAT BELT CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (SEAT BELT CONTROL ECU - BATTERY AND BODY GROUND)
a.
U165213E01
1.804,2.537 2.057,2.679 0.253,0.142 10 IG1 1.92,2.855 2.114,2.993 0.194,0.139 10 +B 0.083,0.047 0.277,0.186 0.194,0.139 10 *a 0.123,2.849 0.561,2.991 0.438,0.142 10 PGND 0.21,1.693 0.491,1.831 0.281,0.138 10 E41 2.948,1.693 3.230,1.831 0.281,0.138 10 E42 0.648,2.935 0.81,2.935 0.81,2.935 1.146,2.276 false 1.89,2.935 1.728,2.935 1.728,2.935 1.391,2.276 false 2.108,2.62 2.191,2.62 2.191,2.62 2.355,2.47 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the E41 seat belt control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E41-7 (+B) - Body ground Always 11 to 14 V
E42-8 (IG1) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E41-8 (PGND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Seat Belt Control ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR