Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255534 CAN COMMUNICATION SYSTEM(for RHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  U0132  Lost Communication with Ride Level Control Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0132 There is no communication from the suspension control ECU.
·

Power source circuit of suspension control ECU

·

Suspension control ECU CAN branch wire or connector

·

Suspension control ECU



For vehicles with active height control suspension.


WIRING DIAGRAM

C177459E06
0.333,1.87 2.291,2.093 1.959,0.223 10 No. 1 CAN Junction Connector 5.821,2.216 6.338,2.400 0.517,0.184 10 BAT 5.821,3.975 6.338,4.159 0.517,0.184 10 GND 5.473,3.986 5.782,4.150 0.309,0.164 10 K35 5.473,2.231 5.782,2.396 0.309,0.166 10 K35 5.551,2.048 5.739,2.225 0.188,0.177 10 1 5.558,3.811 5.685,3.989 0.127,0.177 10 6 5.821,3.612 6.338,3.796 0.517,0.184 10 GND 5.473,3.623 5.782,3.767 0.309,0.144 10 K34 5.558,3.448 5.685,3.626 0.127,0.177 10 1 4.49,2.085 4.988,2.267 0.498,0.181 10 AHC-B 5.821,2.58 6.338,2.763 0.517,0.184 10 BAT2 5.473,2.594 5.782,2.760 0.309,0.166 10 K34 5.551,2.411 5.739,2.589 0.188,0.177 10 3 4.338,2.449 5.182,2.630 0.844,0.181 10 AHC-B No. 2 5.821,2.98 6.338,3.164 0.517,0.184 10 IG 5.473,2.995 5.782,3.160 0.309,0.166 10 K34 5.551,2.812 5.739,2.989 0.188,0.177 10 5 4.268,2.849 5.157,3.031 0.889,0.181 10 ECU-IG No. 4 2.085,2.98 3.409,3.188 1.324,0.208 10 from IG NO. 4 Relay 2.622,2.221 3.417,2.429 0.795,0.208 10 from Battery 5.821,0.903 6.338,1.087 0.517,0.184 10 CANH 5.821,1.328 6.338,1.511 0.517,0.184 10 CANL 5.411,4.826 7.044,4.987 1.633,0.161 10 Suspension Control ECU 5.469,0.896 5.783,1.068 0.315,0.172 10 K34 5.554,0.707 5.668,0.885 0.114,0.177 10 7 5.559,1.159 5.697,1.337 0.138,0.177 10 8 5.467,1.328 5.782,1.500 0.315,0.172 10 K34 1.903,0.806 2.018,0.984 0.114,0.177 10 1 1.908,1.233 2.047,1.411 0.138,0.177 10 2 0.333,1.695 0.647,1.867 0.315,0.172 10 K30

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE)
a.
U165211E02
2.156,1.208 2.313,1.073 2.313,1.073 2.438,1.073 false 2.073,1.198 2.323,0.781 2.323,0.781 2.448,0.781 false 0.552,1.188 0.854,1.417 0.302,0.229 10 false K34 0.063,0.031 0.375,0.26 0.313,0.229 10 false *a 2.469,1 3.063,1.229 0.594,0.229 10 false CANH 2.479,0.698 3.042,0.885 0.563,0.188 10 false CANL

Disconnect the K34 suspension control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K34-7 (CANH) - K34-8 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Suspension Control ECU)



OK

4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SUSPENSION CONTROL ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BATTERY AND BODY GROUND)
a.
U165221E01
0.899,2.058 1.193,2.199 0.294,0.141 10 IG 0.073,0.039 0.346,0.179 0.273,0.141 10 *a 1.412,0.78 1.173,0.541 1.173,0.541 1.048,0.541 false 0.567,0.86 0.832,1.001 0.265,0.141 10 K35 2.506,2.43 2.771,2.571 0.265,0.141 10 K34 2.363,0.367 2.784,0.507 0.421,0.141 10 BAT 1.998,0.75 2.213,0.448 2.213,0.448 2.338,0.448 false 0.551,2.564 0.972,2.705 0.421,0.141 10 GND 1.494,2.376 1.255,2.137 1.255,2.137 1.131,2.137 false 0.624,0.458 1.045,0.599 0.421,0.141 10 GND 1.785,2.376 2.236,2.073 2.236,2.073 2.36,2.073 false 2.384,1.994 2.838,2.135 0.453,0.141 10 BAT2 1.355,2.418 1.133,2.643 1.133,2.643 0.971,2.643 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the K35 suspension control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K35-1 (BAT) - Body ground Always 11 to 14 V
K34-3 (BAT2) - Body ground Always 11 to 14 V
K34-5 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K34-1 (GND) - Body ground Always Below 1 Ω
K35-6 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Suspension Control ECU)


OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR