Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255534 CAN COMMUNICATION SYSTEM(for RHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  U0141  Lost Communication with Body Control Module "A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0141 There is no communication from the No. 2 main body ECU.
·

Power source circuit of No. 2 main body ECU

·

No. 2 main body ECU CAN branch wire or connector

·

No. 2 main body ECU



For vehicles with a power back door system.


WIRING DIAGRAM

C180679E03
5.482,0.995 5.887,1.133 0.406,0.138 10 MPX+ 5.198,0.868 5.391,1.054 0.193,0.186 10 11 5.482,1.415 5.887,1.553 0.406,0.138 10 MPX- 5.198,1.297 5.391,1.483 0.193,0.186 10 12 1.79,0.868 1.983,1.054 0.193,0.186 10 1 1.79,1.297 1.983,1.483 0.193,0.186 10 2 5.198,2.458 5.391,2.644 0.193,0.186 10 14 4.393,2.441 4.925,2.583 0.532,0.141 10 ECU-B2 2.932,2.577 3.721,2.720 0.788,0.142 10 from Battery 0.562,1.75 1.382,1.936 0.819,0.186 10 L57 0.562,1.917 2.541,2.103 1.979,0.186 10 No. 2 CAN Junction Connector 2.435,3.317 3.716,3.459 1.281,0.142 10 from IG NO. 4 Relay 4.218,3.172 5.097,3.314 0.879,0.141 10 ECU-IG No. 4 5.482,3.312 5.887,3.457 0.406,0.144 10 SIG 5.482,2.577 5.887,2.721 0.406,0.144 10 BECU 5.198,3.191 5.391,3.377 0.193,0.186 10 13 5.482,4.048 5.887,4.192 0.406,0.144 10 GND 5.266,4.561 5.672,4.747 0.406,0.186 10 L50 5.266,4.756 6.679,4.942 1.412,0.186 10 No. 2 Main Body ECU 5.292,3.924 5.392,4.110 0.100,0.186 10 7

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 MAIN BODY ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 MAIN BODY ECU CAN BRANCH WIRE)
a.
U165219E01
2.737,1.009 2.986,1.150 0.250,0.141 10 L50 0.039,0.039 0.311,0.179 0.273,0.141 10 *a 0.3,1.295 0.721,1.436 0.421,0.141 10 MPX- 1.105,1.091 0.907,1.372 0.907,1.372 0.783,1.372 false 0.51,1.604 0.931,1.745 0.421,0.141 10 MPX+ 1.257,1.091 1.147,1.681 1.147,1.681 1.022,1.681 false

Disconnect the L50 No. 2 main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L50-11 (MPX+) - L50-12 (MPX-) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Main Body ECU)



OK

4.CHECK HARNESS AND CONNECTOR (NO. 2 MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE NO. 2 MAIN BODY ECU CAN BRANCH WIRE OR CONNECTOR (MPX+, MPX-)

4.CHECK HARNESS AND CONNECTOR (NO. 2 MAIN BODY ECU - BATTERY AND BODY GROUND)
a.
U165220E01
0.373,1.009 0.623,1.150 0.250,0.141 10 L50 0.039,0.039 0.311,0.179 0.273,0.141 10 *a 2.626,1.307 2.901,1.448 0.275,0.141 10 SIG 2.309,1.183 2.476,1.384 2.476,1.384 2.6,1.384 false 2.481,1.593 2.902,1.734 0.421,0.141 10 BECU 2.24,1.197 2.33,1.67 2.33,1.67 2.455,1.67 false 1.692,1.095 1.382,1.689 1.382,1.689 1.257,1.689 false 0.839,1.605 1.174,1.746 0.335,0.141 10 GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L50-14 (BECU) - Body ground Always 11 to 14 V
L50-13 (SIG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L50-7 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Main Body ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR