Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255534 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Multi-media Module Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Multi-media Module Receiver Assembly Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN)" is not displayed on the "Bus Check" screen.

·

"Multi-media Module Receiver Assembly Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside of multi-media module receiver assembly

·

Multi-media module receiver assembly CAN branch wire or connector

·

Multi-media module receiver assembly



For vehicles with an navigation system.


WIRING DIAGRAM

C175531E14
2.95,2.591 3.740,2.750 0.791,0.159 10 from Battery 2.716,3.11 3.769,3.268 1.053,0.159 10 from ACC Relay 2.379,3.621 3.755,3.780 1.376,0.159 10 from IG1 NO. 1 Relay 4.555,2.463 4.806,2.608 0.251,0.145 10 TV 4.51,2.963 4.961,3.109 0.452,0.145 10 ACC 4.228,3.478 5.168,3.623 0.940,0.146 10 ECU-IG No. 1 5.209,2.51 5.388,2.669 0.178,0.159 10 17 5.216,3.023 5.388,3.182 0.171,0.159 10 16 5.216,3.519 5.388,3.678 0.171,0.159 10 15 5.213,4.001 5.388,4.160 0.175,0.159 10 12 5.481,2.626 5.755,2.778 0.274,0.152 10 +B1 5.481,3.143 5.968,3.295 0.487,0.152 10 ACC1 5.481,3.632 5.653,3.784 0.172,0.152 10 IG 5.481,4.107 5.887,4.259 0.405,0.152 10 GND1 5.286,0.929 5.384,1.088 0.099,0.159 10 1 5.481,1.011 5.945,1.163 0.464,0.152 10 CANH 5.286,1.366 5.384,1.525 0.099,0.159 10 2 1.798,0.929 1.973,1.088 0.175,0.159 10 2 1.798,1.366 1.973,1.525 0.175,0.159 10 13 5.481,1.449 5.945,1.601 0.464,0.152 10 CANL 5.07,4.606 5.337,4.758 0.267,0.152 10 F77 5.07,4.775 6.888,5.093 1.818,0.317 10 Multi-media Module Receiver Assembly 0.498,1.765 0.765,1.917 0.267,0.152 10 E69 0.498,1.934 2.107,2.086 1.609,0.152 10 No. 2 Junction Connector

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

For vehicles with an SRS system:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (MULTI-MEDIA MODULE RECEIVER ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (MULTI-MEDIA MODULE RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
U165197E01
0.454,1.11 0.679,2.015 0.679,2.015 0.851,2.015 false 1.017,1.786 0.888,1.786 0.888,1.786 0.551,1.11 false 1.04,1.709 1.462,1.846 0.422,0.137 10 CANL 0.879,1.941 1.302,2.078 0.422,0.137 10 CANH 0.054,0.044 0.477,0.182 0.422,0.137 10 *a 1.577,0.377 1.835,0.514 0.259,0.137 10 F77

Disconnect the F77 multi-media module receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F77-1 (CANH) - F77-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165198E01
2.538,1.025 2.8,0.596 2.8,0.596 2.972,0.596 false 1.771,0.615 1.9,0.615 1.9,0.615 2.108,1.033 false 3.019,0.517 3.212,0.654 0.193,0.137 10 IG 1.255,0.526 1.677,0.663 0.422,0.137 10 GND1 0.054,0.044 0.477,0.182 0.422,0.137 10 *a 1.576,0.219 1.838,0.357 0.262,0.137 10 F77 2.121,1.902 2.543,2.039 0.422,0.137 10 +B1 1.81,1.646 2.233,1.783 0.422,0.137 10 ACC1 2.295,1.737 2.424,1.737 2.424,1.737 2.697,1.126 false 2.295,1.737 2.424,1.737 2.424,1.737 2.697,1.126 false 2.457,1.993 2.586,1.993 2.586,1.993 2.848,1.133 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-12 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F77-17 (+B1) - Body ground Always 11 to 14 V
F77-16 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
F77-15 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)


OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR