Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU (smart key ECU assembly) intermittently monitors the LIN communication bus between the components related to certification. DTC B2785 is output when a malfunction in the LIN communication bus between the components related to certification is detected continuously 3 times.

DTC Code DTC Detection Condition Trouble Area
B2785 The certification ECU (smart key ECU assembly) detects a malfunction in the LIN communication bus between components related to certification continuously 3 times.
·

Certification ECU (smart key ECU assembly)

·

ID code box (immobiliser code ECU)

·

Steering Lock Actuator Assembly (Steering lock ECU)

·

Harness or connector



WIRING DIAGRAM

E334748E07
2.354,1.021 2.677,1.25 0.323,0.229 10 false LIN 4.656,3.146 4.979,3.375 0.323,0.229 10 false LIN 4.656,1.021 4.979,1.25 0.323,0.229 10 false LIN1 1.302,1.552 1.729,1.729 0.427,0.177 10 false E130 1.292,1.719 3.135,2.083 1.844,0.365 10 false Certification ECU (Smart Key ECU Assembly) 4.531,1.542 4.99,1.708 0.458,0.167 10 false E124 4.229,3.708 4.656,3.885 0.427,0.177 10 false E26 4.219,3.885 6.375,4.531 2.156,0.646 10 false Steering Lock Actuator Assembly (Steering Lock ECU) 4.531,1.74 6.135,2.083 1.604,0.344 10 false ID Code Box (Immobiliser Code ECU) 2.729,0.854 2.938,1.042 0.208,0.188 10 false 6 4.417,0.885 4.615,1.052 0.198,0.167 10 false 2 4.417,3.01 4.615,3.177 0.198,0.167 10 false 5 0.583,4.396 2.323,4.604 1.74,0.208 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.


HINT:

When DTC B2785 is output simultaneously, perform the troubleshooting.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX AND STEERING LOCK ECU)
a.

Disconnect the E26 and E124 and E130 ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E130-6 (LIN) - E124-2 (LIN1) Always Below 1 Ω
E130-6 (LIN) - E26-5 (LIN) Always Below 1 Ω
E130-6 (LIN) - Body ground Always Below 1 Ω
E124-2 (LIN1) - Body ground Always 10 kΩ or higher
E26-5 (LIN) - Body ground Always 10 kΩ or higher




OK

2.CHECK FOR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FOR DTC
a.

Reconnect the E124 ECU connectors.



c.

Recheck for DTCs.

Result
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

3.CHECK FOR DTC

B

4.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
3.CHECK FOR DTC
a.

Reconnect the E26 ECU connector.


b.

Disconnect the E124 ECU connector.



d.

Recheck for DTCs.

Result
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

6.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
4.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
a.

for Manual Tilt and Manual Telescopic Steering Column

i.

Temporarily replace the steering lock ECU with a new or normally functioning one (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY).



b.

for Power Tilt and Power Telescopic Steering Column

i.

Temporarily replace the steering lock ECU with a new or normally functioning one (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY).





NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Recheck for DTCs.

Result
Result Proceed to
DTC B2785 is not output A
DTC B2785 is output B



A

END (STEERING LOCK ECU IS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Temporarily replace the ID code box immobiliser code ECU with a new or normally functioning one.




NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2785 is not output A
DTC B2785 is output B



A

END (ID CODE BOX IS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)