Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2786  No Response from Steering Lock ECU  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock actuator (steering lock ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2786 Periodic transmission from the steering lock ECU stops for 10 seconds or more.
·

Steering lock actuator (Steering lock ECU)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

U163931E02
0.948,4.708 1.615,4.906 0.667,0.198 10 false : LIN Line 0.594,3.875 1.448,4.073 0.854,0.198 10 false from Battery 1.75,4.021 2.51,4.219 0.76,0.198 10 false STR LOCK 3.448,4.302 3.802,4.479 0.354,0.177 10 false E26 3.354,3.75 3.51,3.927 0.156,0.177 10 false 7 3.354,2.99 3.51,3.167 0.156,0.177 10 false 5 3.313,1.146 3.5,1.323 0.188,0.177 10 false 10 3.563,3.135 4,3.313 0.438,0.177 10 false LIN 3.563,1.292 3.823,1.469 0.26,0.177 10 false LIN 4.26,3.146 4.594,3.323 0.333,0.177 10 false GND 4.656,2.99 4.792,3.167 0.135,0.177 10 false 1 3.563,3.875 4,4.052 0.438,0.177 10 false B 3.448,4.458 4.958,4.802 1.51,0.344 10 false Steering Lock Actuator (Steering Lock ECU) 3.5,1.875 3.771,2.052 0.271,0.177 10 false E29 3.5,2.031 5.135,2.396 1.635,0.365 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.


HINT:

DTC B2785 is stored when the communication between the steering lock ECU and certification ECU (smart key ECU assembly) stops.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2786 is output A
DTC B2786 is not output B



A

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)

B

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)
U165878E01
1.603,1.826 1.749,1.826 1.749,1.826 2.396,1.279 false 0.902,4.335 1.048,4.335 1.048,4.335 1.968,3.766 false 0.06,0.028 2.418,0.352 2.358,0.324 10 Front view of wire harness connector: (to Certification ECU) 0.06,2.052 2.418,2.376 2.358,0.324 10 Front view of wire harness connector: (to Steering Lock ECU) 0.252,1.056 0.550,1.233 0.298,0.177 10 E29 0.266,3.636 0.565,3.812 0.298,0.177 10 E26 1.267,1.748 1.568,1.903 0.301,0.155 10 LIN 0.592,4.227 0.893,4.382 0.301,0.155 10 LIN

a.

Disconnect the E29 and E26 ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E29-10 (LIN) - E26-5 (LIN) Always Below 1 Ω
E29-10 (LIN) or E26-5 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK STEERING LOCK ACTUATOR (BATTERY VOLTAGE AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK STEERING LOCK ACTUATOR (BATTERY VOLTAGE AND BODY GROUND)
a.
U163899E01
0.234,0.026 2.598,0.404 2.364,0.378 10 Front view of wire harness connector: (to Steering Lock ECU) 0.575,1.049 0.842,1.212 0.267,0.163 10 E26 0.678,1.762 1.049,1.925 0.371,0.163 10 GND 2.38,1.719 2.536,1.882 0.156,0.163 10 B 1.273,1.401 0.947,1.728 false 2.167,1.393 2.38,1.719 false

Disconnect the E26 ECU connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
E26-7 (B) - Body ground Always 11 to 14 V




OK

5.REPLACE STEERING LOCK ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE STEERING LOCK ACTUATOR ASSEMBLY
a.

Temporarily replace the steering lock actuator with a new or normally functioning one (See page Steering>STEERING COLUMN>MULTIPLEX TILT AND TELESCOPIC ECU>REMOVAL).




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2786 is not output A
DTC B2786 is output B



A

END (STEERING LOCK ECU IS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)