Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2786  No Response from Steering Lock ECU  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock actuator (steering lock ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2786 Periodic transmission from the steering lock ECU stops for 10 seconds or more.
·

Steering lock actuator (Steering lock ECU)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

E340372E01
0.57,6.382 2.185,6.563 1.615,0.181 10 : LIN Communication Line 3.89,3.65 4.216,3.831 0.326,0.181 10 GND 3.222,3.65 3.533,3.831 0.310,0.181 10 LIN 3.26,1.128 3.570,1.310 0.310,0.181 10 LIN 3.232,4.453 3.388,4.635 0.156,0.181 10 B 2.995,3.524 3.151,3.705 0.156,0.181 10 5 3.005,0.969 3.160,1.151 0.156,0.181 10 6 4.373,3.51 4.529,3.691 0.156,0.181 10 1 3.005,4.351 3.160,4.532 0.156,0.181 10 7 2.824,5.093 3.423,5.274 0.599,0.181 10 E26 2.907,1.768 3.323,1.949 0.416,0.181 10 E130 2.964,1.93 4.589,2.244 1.625,0.313 10 Certification ECU (Smart Key ECU Assembly) 0.513,4.462 1.591,4.729 1.078,0.267 10 from Battery 1.801,4.676 2.834,4.943 1.032,0.267 10 STRG LOCK 2.82,5.283 4.926,5.629 2.106,0.346 10 Steering Lock Actuator Assembly (Steering Lock ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

DTC B2785 is stored when the communication between the steering lock ECU and certification ECU (smart key ECU assembly) stops.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2786 is output A
DTC B2786 is not output B



A

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)

B

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STEERING LOCK ECU)
a.

Disconnect the E26 and E130 ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E130-6 (LIN) - E26-5 (LIN) Always Below 1 Ω
E130-6 (LIN) or E26-5 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY BATTERY AND BODY GROUND)
a.
U163900E01
0.085,0.066 2.449,0.445 2.364,0.378 10 *a 0.545,1.049 0.812,1.212 0.267,0.163 10 E26 0.678,1.762 1.049,1.925 0.371,0.163 10 GND 2.38,1.719 2.536,1.882 0.156,0.163 10 B 1.273,1.401 0.947,1.728 false 2.167,1.393 2.38,1.719 false

Disconnect the E26 ECU connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
E26-7 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Steering Lock Actuator [Steering Lock ECU])


OK

5.REPLACE STEERING LOCK ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE STEERING LOCK ACTUATOR ASSEMBLY
a.

for Manual Tilt and Manual Telescopic Steering Column

i.

Temporarily replace the steering lock actuator with a new or normally functioning one (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY).



b.

for Power Tilt and Power Telescopic Steering Column

i.

Temporarily replace the steering lock actuator with a new or normally functioning one (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY).





NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2786 is not output A
DTC B2786 is output B



A

END (STEERING LOCK ACTUATOR ASSEMBLY IS DEFECTIVE)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR