Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2789  No Response from ID BOX  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2789 No communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) for 10 seconds or more.
·

ID code box (immobiliser code ECU)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

U163929E02
0.948,4.708 1.615,4.906 0.667,0.198 10 false : LIN Line 0.594,3.885 1.448,4.083 0.854,0.198 10 false from Battery 1.938,4.031 2.698,4.229 0.76,0.198 10 false IMB 3.5,4.292 3.854,4.469 0.354,0.177 10 false E28 3.354,3.75 3.51,3.927 0.156,0.177 10 false 1 3.354,2.99 3.51,3.167 0.156,0.177 10 false 3 3.313,1.146 3.5,1.323 0.188,0.177 10 false 10 3.563,3.146 4,3.323 0.438,0.177 10 false LIN1 3.563,1.292 3.823,1.469 0.26,0.177 10 false LIN 4.26,3.135 4.594,3.313 0.333,0.177 10 false GND 4.656,2.99 4.792,3.167 0.135,0.177 10 false 8 3.563,3.875 4,4.052 0.438,0.177 10 false +B 3.5,4.458 6.156,4.771 2.656,0.313 10 false ID Code Box (Immobiliser Code ECU) 3.5,1.896 3.771,2.073 0.271,0.177 10 false E29 3.5,2.063 6.417,2.344 2.917,0.281 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.


HINT:

DTC B2785 is stored when the communication between the ID code box (immobiliser code ECU) and certification ECU (smart key ECU assembly) stops.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2789 is output A
DTC B2789 is not output B



A

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX)

B

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX)
U165873E01
1.323,2.192 1.469,2.192 1.469,2.192 2.116,1.645 false 0.963,4.207 1.109,4.207 1.109,4.207 1.534,3.909 false 0.08,0 2.472,0.311 2.393,0.311 10 Front view of wire harness connector: (to Certification ECU) 0.08,2.359 2.472,2.670 2.393,0.311 10 Front view of wire harness connector: (to ID Code Box) 0.193,0.937 0.510,1.120 0.317,0.184 10 E29 0.197,3.434 0.514,3.618 0.317,0.184 10 E28 1.012,2.102 1.291,2.277 0.279,0.176 10 LIN 0.57,4.117 0.905,4.293 0.335,0.176 10 LIN1

a.

Disconnect the E29 ECU connector.


b.

Disconnect the E28 box connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E29-10 (LIN) - E28-3 (LIN1) Always Below 1 Ω
E29-10 (LIN) or E28-3 (LIN1) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX - BATTERY AND BODY GROUND)
a.
U163868E02
1.313,1.167 1.031,1.469 false 2.115,1.188 2.302,1.5 false 0.104,0.063 2.5,0.563 2.396,0.5 10 false Front view of wire harness connector: (to ID Code Box) 0.823,1.469 1.083,1.677 0.26,0.208 10 false +B 2.26,1.531 2.604,1.74 0.344,0.208 10 false GND 0.469,0.99 0.813,1.198 0.344,0.208 10 false E28

Disconnect the E28 box connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
E28-8 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
E28-1 (+B) - Body ground Always 11 to 14 V




OK

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Temporarily replace the ID code box (immobiliser code ECU) with a new or normally functioning one.




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2789 is output A
DTC B2789 is not output B



A

END (ID CODE BOX IS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)