Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2789  No Response from ID BOX  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2789 No communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) for 10 seconds or more.
·

ID code box (immobiliser code ECU)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

E340372E03
0.602,6.392 2.217,6.573 1.615,0.181 10 : LIN Communication Line 3.886,3.641 4.211,3.822 0.326,0.181 10 GND 3.274,3.641 3.584,3.822 0.310,0.181 10 LIN1 3.255,1.128 3.565,1.310 0.310,0.181 10 LIN 3.264,4.458 3.532,4.639 0.269,0.181 10 +B 3.014,3.519 3.170,3.701 0.156,0.181 10 2 3.014,0.984 3.170,1.165 0.156,0.181 10 6 4.34,3.51 4.496,3.691 0.156,0.181 10 5 3.014,4.36 3.170,4.541 0.156,0.181 10 1 2.536,5 3.030,5.181 0.494,0.181 10 E124 2.981,1.843 3.398,2.024 0.416,0.181 10 E130 2.983,2.005 4.608,2.318 1.625,0.313 10 Certification ECU (Smart Key ECU Assembly) 0.597,4.471 1.675,4.738 1.078,0.267 10 from Battery 2.012,4.625 2.627,4.873 0.615,0.248 10 IMMOBI 2.536,5.153 5.318,5.498 2.782,0.346 10 ID Code Box (Immobiliser Code ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

DTC B2785 is stored when the communication between the ID code box (immobiliser code ECU) and certification ECU (smart key ECU assembly) stops.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2789 is output A
DTC B2789 is not output B



A

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX)

B

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX)
a.

Disconnect the E130 ECU connector.


b.

Disconnect the E124 box connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E130-6 (LIN) - E124-2 (LIN1) Always Below 1 Ω
E130-6 (LIN) or E124-2 (LIN1) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILIZER CODE ECU) [BATTERY AND BODY GROUND])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILIZER CODE ECU) [BATTERY AND BODY GROUND])
a.
U166596E01
0.117,0.142 0.401,0.393 0.283,0.251 10 *a 1.563,0.432 1.907,0.572 0.343,0.140 10 E124 2.44,1.701 2.783,1.841 0.343,0.140 10 GND 0.775,1.701 1.119,1.841 0.343,0.140 10 +B 2.045,1.537 2.284,1.776 2.284,1.776 2.406,1.776 false 1.424,1.537 1.185,1.776 1.185,1.776 1.063,1.776 false

Disconnect the E124 box connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
E124-5 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
E124-1 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ID Code Box [Immobiliser Code ECU])



OK

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Temporarily replace the ID code box (immobiliser code ECU) with a new or normally functioning one.




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2789 is output A
DTC B2789 is not output B



A

END (ID CODE BOX IS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)