Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the front power window regulator motor LH*1 (RH*2) and main body ECU (cowl side junction block LH) stops for 10 seconds or more.

HINT:
·

*1: for LHD

·

*2: for RHD



DTC Code DTC Detection Condition Trouble Area
B2321 No communication between the front power window regulator motor LH*1 or RH*2 and main body ECU (cowl side junction block LH) for 10 seconds or more.
·

Front power window regulator motor LH*1

·

Front power window regulator motor RH*2

·

Main body ECU (cowl side junction block LH)

·

Harness or connector



WIRING DIAGRAM

U163930E02
1.99,2.24 2.125,2.271 0.135,0.031 0.917,4.719 1.583,4.917 0.667,0.198 10 false : LIN Line 0.552,3.875 1.448,4.073 0.896,0.198 10 false from Battery 1.688,4.031 2.708,4.229 1.021,0.198 10 false FR DOOR LH*1 1.688,4.24 2.833,4.438 1.146,0.198 10 false FR DOOR RH*2 0.365,4.99 1.292,5.188 0.927,0.198 10 false *1: for LHD 0.365,5.271 1.292,5.469 0.927,0.198 10 false *2: for RHD 3.448,4.302 4.688,4.479 1.24,0.177 10 false I12*1, I4*2 3.354,3.771 3.51,3.948 0.156,0.177 10 false 2 3.354,3.01 3.51,3.188 0.156,0.177 10 false 9 3.313,1.146 3.5,1.323 0.188,0.177 10 false 10 3.563,3.156 4,3.333 0.438,0.177 10 false LIN 3.563,1.292 4,1.469 0.438,0.177 10 false LIN2 4.271,3.146 4.604,3.323 0.333,0.177 10 false GND 4.656,3.01 4.792,3.188 0.135,0.177 10 false 1 3.563,3.875 4,4.052 0.438,0.177 10 false B 3.448,4.49 6.583,4.979 3.135,0.49 10 false Front Power Window Regulator Motor LH*1, RH*2 3.5,1.896 3.771,2.073 0.271,0.177 10 false E3 3.5,2.083 5.073,2.573 1.573,0.49 10 false Main Body ECU (Cowl Side Junction Block LH)

CAUTION / NOTICE / HINT

NOTICE:

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.


HINT:

DTC B2325 is stored when the communication between the front power window regulator motor and main body ECU (cowl side junction block LH) stops.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2321 is output A
DTC B2321 is not output B



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR)

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR)
U165869E02
2.448,4.344 2.219,4.344 2.219,4.344 1.76,3.958 false 2.49,1.646 2.323,1.646 2.323,1.646 2.031,1.573 false 0.042,0.052 2.396,0.76 2.354,0.708 10 false Front view of wire harness connector: (to Main Body ECU) 0.042,2.052 2.646,2.781 2.604,0.729 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor LH*1, RH*2) 0.51,1.281 0.76,1.51 0.25,0.229 10 false E3 0.417,3.24 0.729,3.469 0.313,0.229 10 false I12 0.667,3.083 0.896,3.281 0.229,0.198 10 false *1 0.073,3.885 0.99,4.083 0.917,0.198 10 false *1: for LHD 0.073,4.229 0.99,4.427 0.917,0.198 10 false *2: for RHD 2.5,3.24 2.729,3.438 0.229,0.198 10 false I4 2.49,4.25 2.958,4.448 0.469,0.198 10 false LIN 2.729,3.083 2.958,3.281 0.229,0.198 10 false *2 2.521,1.563 2.979,1.76 0.458,0.198 10 false LIN2

a.

Disconnect the E3 ECU connector.


b.

Disconnect the I12*1 or I4*2 motor connector.

HINT:
·

*1: for LHD

·

*2: for RHD




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E3-10 (LIN2) - I12-9 (LIN)*1 or I4-9 (LIN)*2 Always Below 1 Ω




OK

4.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (BATTERY VOLTAGE AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (BATTERY VOLTAGE AND BODY GROUND)
a.
U163898E01
0.237,0.12 2.615,0.679 2.378,0.559 10 Front view of wire harness connector: (to Front Power Window Regulator Motor LH*1, RH*2) 0.53,1.788 0.825,1.951 0.295,0.163 10 I12 0.856,1.677 1.151,1.840 0.295,0.163 10 *1 0.125,2.727 1.010,2.889 0.885,0.163 10 *1: for LHD 0.125,3.036 1.010,3.199 0.885,0.163 10 *2: for RHD 2.355,1.788 2.650,1.951 0.295,0.163 10 I4 2.632,1.677 2.927,1.840 0.295,0.163 10 *2 0.644,2.254 0.992,2.417 0.348,0.163 10 GND 2.144,2.253 2.320,2.416 0.177,0.163 10 B 1.526,2.174 1.101,2.312 false 1.861,2.17 2.119,2.303 false

Disconnect the I12*1 or I4*2 motor connector.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-1 (GND)*1 or I4-1 (GND)*2 - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
I12-2 (B)*1 or I4-2 (B)*2 - Body ground Always 11 to 14 V




OK

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
a.

Temporarily replace the front power window regulator motor LH*1 or RH*2 with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Front Door)>REMOVAL).

HINT:
·

*1: for LHD

·

*2: for RHD






NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Recheck for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2321 is not output A
DTC B2321 is output B



A

END (FRONT POWER WINDOW REGULATOR MOTOR IS DEFECTIVE)

B

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)