Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2014.08–2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255535 LIN COMMUNICATION SYSTEM J

NETWORKING  LIN COMMUNICATION SYSTEM  Rain Sensor LIN Communication Malfunction  


DESCRIPTION

The LIN communication of the components related to the rain sensor occurs between the rain sensor and windshield wiper ECU.

WIRING DIAGRAM

E234443E01
1.831,0.562 2.250,0.724 0.420,0.163 10 MPX1 2.349,0.449 2.463,0.605 0.114,0.156 10 7 1.137,1.013 1.428,1.183 0.291,0.170 10 E85 1.137,1.171 2.640,1.355 1.503,0.184 10 Windshield Wiper ECU 1.371,2.043 2.302,2.216 0.931,0.174 10 ECU-IG No. 2 0.219,1.886 1.018,2.087 0.798,0.201 10 from Battery 2.948,1.805 3.121,1.964 0.173,0.159 10 14 3.017,2.197 3.122,2.343 0.105,0.145 10 3 4.135,1.794 4.309,1.957 0.173,0.163 10 29 4.141,2.167 4.248,2.337 0.107,0.170 10 4 5.29,1.768 5.397,1.937 0.107,0.170 10 4 3.645,2.271 4.072,2.441 0.427,0.170 10 GND2 3.827,1.9 4.073,2.055 0.246,0.156 10 IG2 3.193,1.9 3.370,2.055 0.177,0.156 10 IG 3.193,2.274 3.634,2.427 0.441,0.152 10 GND5 2.818,2.698 3.044,2.840 0.225,0.142 10 R7 2.818,2.866 4.447,3.050 1.628,0.184 10 Overhead Junction Block 5.396,2.754 5.693,2.908 0.297,0.154 10 R11 5.396,2.929 6.226,3.106 0.830,0.177 10 Rain Sensor 5.466,2.285 5.719,2.441 0.253,0.156 10 ES 5.263,2.18 5.384,2.336 0.121,0.156 10 1 5.466,1.907 5.747,2.057 0.281,0.151 10 SIG 5.466,0.562 5.820,0.721 0.354,0.159 10 MPX 5.27,0.432 5.398,0.601 0.128,0.169 10 3 0.498,3.358 1.191,3.561 0.693,0.202 10 : LIN Line

CAUTION / NOTICE / HINT

NOTICE:

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - WIND SHIELD WIPER ECU AND OVERHEAD JUNCTION BLOCK)
U164109E01
0.086,0.062 2.458,0.426 2.372,0.364 10 Front view of wire harness connector: (to Windshield Wiper ECU) 3.764,0.062 6.149,0.426 2.385,0.364 10 Front view of wire harness connector: (to Overhead Junction Block) 0.086,2.037 2.471,2.402 2.385,0.364 10 Front view of wire harness connector: (to Rain Sensor) 0.338,1.148 0.612,1.304 0.274,0.156 10 E85 3.687,1.148 3.912,1.304 0.225,0.156 10 R7 0.338,3.05 0.612,3.205 0.274,0.156 10 R11 0.479,1.575 0.891,1.755 0.413,0.180 10 MPX1 0.932,3.508 1.185,3.692 0.253,0.184 10 ES 1.551,3.557 1.889,3.739 0.338,0.182 10 MPX 2.143,3.429 2.459,3.623 0.316,0.194 10 SIG 4.28,1.738 4.722,1.913 0.442,0.175 10 GND2 5.606,1.82 5.894,1.997 0.288,0.177 10 IG2 5.515,1.486 5.716,1.79 false 4.598,1.356 4.481,1.706 false 1.144,1.533 0.878,1.664 false 1.256,3.298 1.064,3.491 false 1.674,3.312 1.674,3.52 false 1.903,3.289 2.102,3.468 false

a.

Disconnect the E85 ECU connector.


b.

Disconnect the R11 sensor connector.


c.

Disconnect the R7 junction block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R11-3 (MPX) - E85-7 (MPX1) Always Below 1 Ω
R11-4 (SIG) - R7-29 (IG2) Always Below 1 Ω
R11-1 (ES) - R7-4 (GND2) Always Below 1 Ω
R11-3 (MPX) - Body ground Always 10 kΩ or higher
R11-4 (SIG) - Body ground Always 10 kΩ or higher
R11-1 (ES) - Body ground Always 10 kΩ or higher



e.

Reconnect the R7 junction block connector.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R11-4 (SIG) - Body ground Ignition switch ON 11 to 14 V




OK

2.REPLACE RAIN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE RAIN SENSOR
a.

Temporarily replace the rain sensor with a new one (See page Vehicle Exterior>WIPER / WASHER>RAIN SENSOR>REMOVAL).


b.

Check the rain sensor function is normal.

OK:

Rain sensor function is normal




OK

END (RAIN SENSOR IS DEFECTIVE)

NG

REPLACE WINDSHIELD WIPER ECU