Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › 2015.08–2016.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) U

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Turn the ignition switch off before measuring the resistances between CAN main wires and between CAN branch wires.

·

Turn the ignition switch off before inspecting CAN wires for a ground short.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



JUNCTION CONNECTOR


a.

NO. 1 CAN JUNCTION CONNECTOR

U165475E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 0.932,0.84 1.275,0.982 0.343,0.142 10 E135 1.676,0.519 2.245,0.662 0.569,0.144 10 CANH*b 1.739,1.066 2.308,1.210 0.569,0.144 10 CANL*b 1.953,1.224 2.522,1.368 0.569,0.144 10 CANL*c 2.508,1.294 2.701,1.294 2.701,1.294 2.834,0.999 false 2.072,1.385 2.641,1.529 0.569,0.144 10 CANL*d 2.308,1.564 2.877,1.707 0.569,0.144 10 CANL*e 2.073,0.195 2.643,0.338 0.569,0.144 10 CANH*d 1.814,0.352 2.384,0.496 0.569,0.144 10 CANH*c 2.343,0.03 2.913,0.174 0.569,0.144 10 CANH*e 4.746,0.371 5.316,0.515 0.569,0.144 10 CANH*h 4.792,0.575 5.361,0.718 0.569,0.144 10 CANH*i 3.709,0.062 4.279,0.205 0.569,0.144 10 CANH*f 4.457,0.179 5.026,0.323 0.569,0.144 10 CANH*g 4.457,1.303 5.026,1.446 0.569,0.144 10 CANL*h 4.788,1.127 5.357,1.271 0.569,0.144 10 CANL*i 4.212,1.451 4.781,1.595 0.569,0.144 10 CANL*g 3.747,1.614 4.317,1.757 0.569,0.144 10 CANL*f 3.928,0.839 4.335,0.244 4.335,0.244 4.433,0.244 false 3.419,0.844 3.598,0.126 3.598,0.126 3.696,0.126 false 2.412,0.418 2.604,0.418 2.604,0.418 2.834,0.847 false 2.629,0.271 2.87,0.271 2.87,0.271 3.014,0.836 false 2.916,0.096 3.158,0.096 3.158,0.096 3.233,0.831 false 3.928,1.007 4.093,1.52 4.093,1.52 4.191,1.52 false 4.356,0.839 4.661,0.64 4.661,0.64 4.759,0.64 false 4.356,1.007 4.659,1.203 4.659,1.203 4.757,1.203 false 2.609,0.839 2.364,0.595 2.364,0.595 2.266,0.595 false 2.609,1.007 2.392,1.132 2.392,1.132 2.294,1.132 false 2.508,1.294 2.701,1.294 2.701,1.294 2.834,0.999 false 2.608,1.446 2.849,1.446 2.849,1.446 3.014,1.01 false 2.869,1.628 2.988,1.628 2.988,1.628 3.233,1.015 false 3.429,1.02 3.595,1.674 3.595,1.674 3.725,1.674 false 4.722,0.434 4.581,0.434 4.581,0.434 4.165,0.837 false 4.176,1.005 4.312,1.373 4.312,1.373 4.424,1.373 false

Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b for No. 2 CAN Junction Connector
*c for 4WD Control ECU *d for Power Steering ECU Assembly (w/ Variable Flow Control Solenoid Valve)
*e for Airbag Sensor Assembly *f for Tire Pressure Warning ECU (w/ Tire Pressure Warning System)
*g for ECM *h for Air Conditioning Amplifier Assembly
*i for Central Gateway ECU - -

No. 1 CAN Junction Connector Wiring Color Connect to
E135-1 (CANH) SB No. 2 CAN junction connector
E135-11 (CANL) W
E135-2 (CANH) P 4WD control ECU
E135-12 (CANL) W
E135-3 (CANH) LG Power steering ECU assembly*1
E135-13 (CANL) W
E135-4 (CANH) GR Airbag sensor assembly
E135-14 (CANL) W
E135-5 (CANH) R Tire pressure warning ECU*2
E135-15 (CANL) W
E135-7 (CANH) V ECM
E135-17 (CANL) W
E135-8 (CANH) G Air conditioning amplifier assembly
E135-18 (CANL) W
E135-9 (CANH) L Central gateway ECU
E135-18 (CANL) W

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System



b.

NO. 2 CAN JUNCTION CONNECTOR

U165476E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 0.932,0.84 1.275,0.982 0.343,0.142 10 E133 1.676,0.519 2.245,0.662 0.569,0.144 10 CANH*b 1.793,1.047 2.363,1.191 0.569,0.144 10 CANL*b 1.904,1.231 2.473,1.375 0.569,0.144 10 CANL*c 2.459,1.301 2.652,1.301 2.652,1.301 2.834,0.999 false 2.067,1.408 2.636,1.552 0.569,0.144 10 CANL*d 2.284,1.595 2.853,1.739 0.569,0.144 10 CANL*e 2.073,0.195 2.643,0.338 0.569,0.144 10 CANH*d 1.814,0.352 2.384,0.496 0.569,0.144 10 CANH*c 2.343,0.03 2.913,0.174 0.569,0.144 10 CANH*e 4.855,0.406 5.424,0.550 0.569,0.144 10 CANH*h 4.893,0.631 5.463,0.774 0.569,0.144 10 CANH*i 4.445,0.034 5.014,0.177 0.569,0.144 10 CANH*f 4.555,0.225 5.124,0.368 0.569,0.144 10 CANH*g 4.481,1.233 5.051,1.376 0.569,0.144 10 CANL*h 4.945,1.078 5.515,1.222 0.569,0.144 10 CANL*i 4.313,1.392 4.883,1.536 0.569,0.144 10 CANL*g 4.212,1.596 4.781,1.740 0.569,0.144 10 CANL*f 3.928,0.839 4.447,0.286 4.447,0.286 4.545,0.286 false 2.412,0.418 2.604,0.418 2.604,0.418 2.834,0.847 false 2.629,0.271 2.87,0.271 2.87,0.271 3.014,0.836 false 2.916,0.096 3.158,0.096 3.158,0.096 3.233,0.831 false 3.737,0.826 4.213,0.105 4.213,0.105 4.427,0.105 false 3.928,1.007 4.181,1.471 4.181,1.471 4.279,1.471 false 4.548,0.839 4.773,0.683 4.773,0.683 4.871,0.683 false 4.548,1.007 4.802,1.15 4.802,1.15 4.9,1.15 false 2.609,0.839 2.364,0.595 2.364,0.595 2.266,0.595 false 2.609,1.007 2.447,1.113 2.447,1.113 2.349,1.113 false 2.459,1.301 2.652,1.301 2.652,1.301 2.834,0.999 false 2.603,1.469 2.844,1.469 2.844,1.469 3.014,1.01 false 2.869,1.659 2.988,1.659 2.988,1.659 3.233,1.015 false 3.737,1.02 3.968,1.657 3.968,1.657 4.182,1.657 false 4.834,0.476 4.693,0.476 4.693,0.476 4.165,0.837 false 4.176,1.005 4.34,1.285 4.34,1.285 4.452,1.285 false

Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b for No. 1 CAN Junction Connector
*c for Main Body ECU (Multiplex Network Body ECU) *d for Master Cylinder Solenoid (Skid Control ECU)
*e for Headlight Swivel ECU Assembly *f for Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System)
*g for Combination Meter Assembly *h for Steering control ECU (w/ Variable Gear Ratio Steering System)
*i for Steering Sensor - -

No. 2 CAN Junction Connector Wiring Color Connect to
E133-1 (CANH) SB No. 1 CAN junction connector
E133-11 (CANL) W
E133-2 (CANH) G Main body ECU (multiplex network body ECU)
E133-12 (CANL) W
E133-3 (CANH) L Master cylinder solenoid (skid control ECU)
E133-13 (CANL) W
E133-4 (CANH) LG Headlight swivel ECU assembly
E133-14 (CANL) B
E133-6 (CANH) B Certification ECU (smart key ECU assembly)*1
E133-16 (CANL) W
E133-7 (CANH) BE Combination meter assembly
E133-17 (CANL) W
E133-8 (CANH) R Steering control ECU*2
E133-18 (CANL) W
E133-10 (CANH) GR Steering sensor
E133-20 (CANL) W

*1: w/ Entry and Start System

*2: w/ Variable Gear Ratio Steering System



c.

NO. 3 CAN JUNCTION CONNECTOR

U165463E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 0.932,0.84 1.275,0.982 0.343,0.142 10 E151 1.856,0.479 2.425,0.623 0.569,0.144 10 CANH*b 1.86,1.224 2.430,1.368 0.569,0.144 10 CANL*b 2.048,1.408 2.617,1.552 0.569,0.144 10 CANL*c 2.603,1.478 2.796,1.478 2.796,1.478 3.184,0.999 false 2.208,1.573 2.777,1.716 0.569,0.144 10 CANL*d 4.087,1.606 4.657,1.749 0.569,0.144 10 CANL*e 2.251,0.111 2.820,0.254 0.569,0.144 10 CANH*d 1.994,0.294 2.563,0.438 0.569,0.144 10 CANH*c 4.048,0.03 4.617,0.174 0.569,0.144 10 CANH*e 4.906,0.62 5.476,0.764 0.569,0.144 10 CANH*h 4.391,0.24 4.960,0.383 0.569,0.144 10 CANH*f 4.66,0.396 5.229,0.540 0.569,0.144 10 CANH*g 4.929,1.06 5.499,1.204 0.569,0.144 10 CANL*h 4.553,1.228 5.122,1.372 0.569,0.144 10 CANL*g 4.452,1.412 5.022,1.556 0.569,0.144 10 CANL*f 4.13,0.839 4.524,0.455 4.524,0.455 4.622,0.455 false 3.737,0.844 3.92,0.098 3.92,0.098 4.018,0.098 false 2.591,0.36 2.784,0.36 2.784,0.36 3.184,0.847 false 2.806,0.187 3.048,0.187 3.048,0.187 3.364,0.836 false 3.939,0.827 4.154,0.301 4.154,0.301 4.368,0.301 false 4.13,1.007 4.42,1.309 4.42,1.309 4.518,1.309 false 3.737,1.003 3.955,1.681 3.955,1.681 4.053,1.681 false 2.991,0.839 2.522,0.531 2.522,0.531 2.424,0.531 false 2.991,1.007 2.54,1.292 2.54,1.292 2.442,1.292 false 4.376,0.839 4.773,0.683 4.773,0.683 4.871,0.683 false 4.376,1.007 4.802,1.15 4.802,1.15 4.9,1.15 false 2.603,1.478 2.796,1.478 2.796,1.478 3.184,0.999 false 2.744,1.633 2.985,1.633 2.985,1.633 3.364,1.01 false 3.939,1.02 4.214,1.486 4.214,1.486 4.428,1.486 false

Text in Illustration
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b for No. 4 CAN Junction Connector
*c for Driving Support ECU Assembly (w/ Pre-crash Safety System) *d for Central Gateway ECU
*e for Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System) *f for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System)
*g for Parking Assist ECU (w/ Multi-terrain Monitor System) *h
·

for Forward Camera Sensor (w/ Pre-crash Safety System)

·

for Inner Rear View Mirror Assembly (w/o Pre-crash Safety System, w/ Automatic High Beam System)



No. 3 CAN Junction Connector Wiring Color Connect to
E151-3 (CANH) W No. 4 CAN junction connector
E151-13 (CANL) B
E151-4 (CANH) L Driving support ECU assembly*1
E151-14 (CANL) B
E151-5 (CANH) SB Central gateway ECU
E151-15 (CANL) B
E151-6 (CANH) L Millimeter wave radar sensor assembly*1
E151-16 (CANL) B
E151-7 (CANH) V Clearance warning ECU assembly*3
E151-17 (CANL) B
E151-8 (CANH) P Parking assist ECU*4
E151-18 (CANL) B
E151-9 (CANH) G
·

Forward camera sensor*1

·

Inner rear view mirror assembly*2, *5


E151-19 (CANL) B

*1: w/ Pre-crash Safety System

*2: w/o Pre-crash Safety System

*3: w/ TOYOTA Parking Assist-sensor System

*4: w/ Multi-terrain Monitor System

*5: w/ Automatic High Beam System



d.

NO. 4 CAN JUNCTION CONNECTOR

HINT:

Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


C342405E01
5.274,2.99 5.468,3.153 5.468,3.153 5.618,3.153 false 5.274,2.844 5.468,2.681 5.468,2.681 5.618,2.681 false 5.653,2.607 6.382,2.860 0.729,0.253 10 CANH 4.21,2.183 4.939,2.436 0.729,0.253 10 *a 5.653,3.087 6.382,3.340 0.729,0.253 10 CANL 2.051,2.875 2.780,3.020 0.729,0.145 10 K57 2.051,3.33 2.780,3.476 0.729,0.145 10 K56 2.051,1.982 2.780,2.127 0.729,0.145 10 K58 2.051,1.74 2.780,1.886 0.729,0.145 10 K65 0.085,0.072 0.813,0.217 0.729,0.145 10 *1

Text in Illustration
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -

No. 4 CAN Junction Connector Wiring Color Connect to
K56-1 (CANH) W No. 3 CAN junction connector
K56-2 (CANL) B
K57-1 (CANH) SB No. 1 CAN junction terminal
K57-2 (CANL) B
K58-1 (CANH) R Blind spot monitor sensor LH*1
K58-2 (CANL) B
K65-1 (CANH) L Suspension control ECU*2
K65-2 (CANL) B

*1: w/ Blind Spot Monitor System

*2: w/ Active Height Control Suspension



e.

NO. 5 CAN JUNCTION CONNECTOR

U165239E01
0.096,0.095 0.391,0.320 0.295,0.225 10 *a 2.285,0.509 2.969,0.660 0.684,0.151 10 CANH*b 2.309,2.485 2.993,2.631 0.684,0.146 10 CANL*b 2.127,1.184 2.811,1.335 0.684,0.151 10 CANH*e 2.221,0.727 2.904,0.879 0.684,0.151 10 CANH*c 2.089,0.939 2.772,1.090 0.684,0.151 10 CANH*d 2.152,1.785 2.835,1.932 0.684,0.146 10 CANL*e 2.152,2.02 2.835,2.167 0.684,0.146 10 CANL*d 2.25,2.262 2.934,2.408 0.684,0.146 10 CANL*c 3.443,0.231 3.793,0.373 0.350,0.142 10 E152 3.023,1.664 2.828,1.849 2.828,1.849 2.714,1.849 false 2.859,2.556 3.035,2.556 3.035,2.556 3.375,1.664 false 3.023,1.454 2.828,1.27 2.828,1.27 2.714,1.27 false 2.869,0.592 3.045,0.592 3.045,0.592 3.375,1.454 false 2.673,1.018 2.831,1.018 2.831,1.018 3.153,1.462 false 2.673,2.105 2.831,2.105 2.831,2.105 3.153,1.661 false

Text in Illustration
*a Rear view of wire harness connector
(to No. 5 CAN Junction Connector)
*b for Central Gateway ECU
*c for Bus Buffer ECU (w/ Bus Buffer ECU) *d
·

for Multi-media Module Receiver Assembly (for Multi-media Module Receiver Type)

·

for Radio and Display Receiver Assembly (for Radio and Display Type)


*e for No. 6 CAN Junction Connector - -

No. 5 CAN Junction Connector Wiring Color Connect to
E152-8 (CANH) R Central gateway ECU
E152-19 (CANL) GR
E152-9 (CANH) BE Bus buffer ECU*1
E152-20 (CANL) GR
E152-10 (CANH) G
·

Multi-media module receiver assembly*2

·

Radio and display receiver assembly*3


E152-21 (CANL) GR
E152-11 (CANH) BE No. 6 CAN junction connector
E152-22 (CANL) GR

*1: w/ Bus Buffer ECU

*2: for Multi-media Module Receiver Type

*3: for Radio and Display Type



f.

NO. 6 CAN JUNCTION CONNECTOR

U165245E01
0.096,0.095 0.391,0.320 0.295,0.225 10 *a 2.211,1.052 2.895,1.203 0.684,0.151 10 CANH*c 2.346,1.932 3.030,2.078 0.684,0.146 10 CANL*c 2.333,2.223 3.017,2.370 0.684,0.146 10 CANL*b 2.198,0.752 2.882,0.903 0.684,0.151 10 CANH*b 3.479,0.231 3.742,0.373 0.264,0.142 10 F99 3.464,1.664 2.994,2.015 2.994,2.015 2.88,2.015 false 2.895,2.311 3.071,2.311 3.071,2.311 3.591,1.664 false 3.464,1.454 2.894,1.122 2.894,1.122 2.78,1.122 false 2.796,0.827 2.971,0.827 2.971,0.827 3.591,1.454 false

Text in Illustration
*a Rear view of wire harness connector
(to No. 6 CAN Junction Connector)
*b for No. 5 CAN Junction Connector
*c for No. 2 CAN Junction Terminal - -

No. 6 CAN Junction Connector Wiring Color Connect to
F99-6 (CANH) BE No. 5 CAN junction connector
F99-17 (CANL) GR
F99-7 (CANH) B No. 2 CAN junction terminal
F99-18 (CANL) GR


g.

NO. 7 CAN JUNCTION CONNECTOR

U165576E01
0.09,0.077 0.392,0.330 0.302,0.253 10 *a 2.354,1.414 2.705,1.554 0.351,0.140 10 E134 4.53,1.263 5.105,1.402 0.575,0.139 10 CANH*b 4.536,1.783 5.111,1.921 0.575,0.139 10 CANL*b 4.475,1.989 5.050,2.128 0.575,0.139 10 CANL*c 4.521,1.03 5.096,1.168 0.575,0.139 10 CANH*c 4.129,1.675 4.344,1.848 4.344,1.848 4.524,1.848 false 4.459,2.061 4.247,2.061 4.247,2.061 4.017,1.675 false 4.129,1.47 4.338,1.326 4.338,1.326 4.518,1.326 false 4.495,1.09 4.284,1.09 4.284,1.09 4.017,1.47 false 3.908,1.675 4.222,2.292 4.222,2.292 4.386,2.292 false 4.358,2.506 4.134,2.506 4.134,2.506 3.807,1.675 false 3.693,1.675 3.886,2.705 3.886,2.705 4.054,2.705 false 3.908,1.462 4.222,0.845 4.222,0.845 4.386,0.845 false 4.358,0.639 4.134,0.639 4.134,0.639 3.807,1.47 false 3.693,1.455 3.886,0.397 3.886,0.397 4.054,0.397 false 4.41,2.224 4.985,2.363 0.575,0.139 10 CANL*d 4.381,2.445 4.955,2.583 0.575,0.139 10 CANL*e 4.065,2.63 4.640,2.769 0.575,0.139 10 CANL*f 4.404,0.78 4.979,0.918 0.575,0.139 10 CANH*d 4.395,0.574 4.969,0.713 0.575,0.139 10 CANH*e 4.086,0.329 4.661,0.468 0.575,0.139 10 CANH*f

Text in Illustration
*a Rear view of wire harness connector
(to No. 7 CAN Junction Connector)
*b for No. 8 CAN Junction Connector
*c for Main Body ECU (Multiplex Network Body ECU) *d for Outer Mirror Control ECU Assembly LH (w/ Memory)
*e for Power Seat Switch Assembly (w/ Memory) *f for Multiplex Tilt and Telescopic ECU (w/ Power Tilt and Power Telescopic Steering Column System)

No. 7 CAN Junction Connector Wiring Color Connect to
E134-1 (CANH) W No. 8 CAN junction connector
E134-12 (CANL) L
E134-2 (CANH) GR Main body ECU (multiplex network body ECU)
E134-13 (CANL) L
E134-3 (CANH) BE Outer mirror control ECU assembly LH*1
E134-14 (CANL) L
E134-4 (CANH) V Power seat switch assembly*1
E134-15 (CANL) L
E134-5 (CANH) P Multiplex Tilt and Telescopic ECU*2
E134-16 (CANL) L

*1: w/ Memory

*2: w/ Power Tilt and Power Telescopic Steering Column System



h.

NO. 8 CAN JUNCTION CONNECTOR

U165577E01
0.09,0.077 0.392,0.330 0.302,0.253 10 *a 2.354,1.414 2.705,1.554 0.351,0.140 10 E136 4.53,1.263 5.105,1.402 0.575,0.139 10 CANH*b 4.536,1.783 5.111,1.921 0.575,0.139 10 CANL*b 4.475,1.989 5.050,2.128 0.575,0.139 10 CANL*c 4.521,1.03 5.096,1.168 0.575,0.139 10 CANH*c 4.129,1.675 4.344,1.848 4.344,1.848 4.524,1.848 false 4.459,2.061 4.247,2.061 4.247,2.061 4.017,1.675 false 4.129,1.47 4.338,1.326 4.338,1.326 4.518,1.326 false 4.495,1.09 4.284,1.09 4.284,1.09 4.017,1.47 false 3.908,1.675 4.222,2.292 4.222,2.292 4.386,2.292 false 3.908,1.462 4.222,0.845 4.222,0.845 4.386,0.845 false 4.41,2.224 4.985,2.363 0.575,0.139 10 CANL*d 4.404,0.78 4.979,0.918 0.575,0.139 10 CANH*d

Text in Illustration
*a Rear view of wire harness connector
(to No. 8 CAN Junction Connector)
*b for No. 7 CAN Junction Connector
*c for No. 9 CAN Junction Connector *d for Outer Mirror Control ECU Assembly RH (w/ Memory)

No. 8 CAN Junction Connector Wiring Color Connect to
E136-1 (CANH) W No. 7 CAN junction connector
E136-12 (CANL) L
E136-2 (CANH) W No. 9 CAN junction connector
E136-13 (CANL) L
E136-3 (CANH) LG Outer mirror control ECU assembly RH*
E136-14 (CANL) L

*: w/ Memory



i.

NO. 9 CAN JUNCTION CONNECTOR

U165573E01
0.09,0.077 0.392,0.330 0.302,0.253 10 *a 2.377,1.414 2.637,1.554 0.261,0.140 10 L71 4.53,1.263 5.105,1.402 0.575,0.139 10 CANH*b 4.536,1.783 5.111,1.921 0.575,0.139 10 CANL*b 4.475,1.989 5.050,2.128 0.575,0.139 10 CANL*c 4.521,1.03 5.096,1.168 0.575,0.139 10 CANH*c 4.129,1.675 4.344,1.848 4.344,1.848 4.524,1.848 false 4.459,2.061 4.247,2.061 4.247,2.061 4.017,1.675 false 4.129,1.47 4.338,1.326 4.338,1.326 4.518,1.326 false 4.495,1.09 4.284,1.09 4.284,1.09 4.017,1.47 false 3.908,1.675 4.222,2.292 4.222,2.292 4.386,2.292 false 4.358,2.506 4.134,2.506 4.134,2.506 3.807,1.675 false 3.908,1.462 4.222,0.845 4.222,0.845 4.386,0.845 false 4.358,0.639 4.134,0.639 4.134,0.639 3.807,1.47 false 4.41,2.224 4.985,2.363 0.575,0.139 10 CANL*d 4.381,2.445 4.955,2.583 0.575,0.139 10 CANL*e 4.404,0.78 4.979,0.918 0.575,0.139 10 CANH*d 4.395,0.574 4.969,0.713 0.575,0.139 10 CANH*e

Text in Illustration
*a Rear view of wire harness connector
(to No. 9 CAN Junction Connector)
*b for No. 8 CAN Junction Connector
*c No. 3 CAN Junction Terminal *d for Power Back Door Unit Assembly (Power Back Door ECU) (w/ Power Back Door System)
*e for No. 2 Main Body ECU (w/ Tail Gate Closer System) - -

No. 9 CAN Junction Connector Wiring Color Connect to
L71-1 (CANH) W No. 8 CAN junction connector
L71-12 (CANL) L
L71-2 (CANH) W No. 3 CAN junction terminal
L71-13 (CANL) L
L71-3 (CANH) V Power back door unit assembly (power back door ECU)*1
L71-14 (CANL) L
L71-4 (CANH) LG No. 2 main body ECU*2
L71-15 (CANL) L

*1: w/ Power Back Door System

*2: w/ Tail Gate Closer System



j.

NO. 10 CAN JUNCTION CONNECTOR (w/ Pre-crash Safety System)

U165464E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 3.433,0.199 3.776,0.341 0.343,0.142 10 E174 2.306,0.248 2.876,0.392 0.569,0.144 10 CANH*b 2.407,1.331 2.976,1.475 0.569,0.144 10 CANL*b 3.993,1.022 4.464,1.438 4.464,1.438 4.562,1.438 false 3.366,1.026 3.06,1.401 3.06,1.401 2.962,1.401 false 3.993,0.844 4.524,0.338 4.524,0.338 4.622,0.338 false 3.366,0.839 2.995,0.324 2.995,0.324 2.897,0.324 false 4.653,0.274 5.223,0.417 0.569,0.144 10 CANH*d 4.31,0.05 4.879,0.193 0.569,0.144 10 CANH*c 4.586,1.373 5.156,1.517 0.569,0.144 10 CANL*d 4.275,1.548 4.844,1.692 0.569,0.144 10 CANL*c 3.803,0.843 4.14,0.126 4.14,0.126 4.294,0.126 false 3.811,1.008 4.095,1.614 4.095,1.614 4.252,1.614 false

Text in Illustration
*a Front view of wire harness connector
(to No. 10 CAN Junction Connector)
*b for Millimeter Wave Radar Sensor Assembly
*c for Forward Recognition Camera *d for Driving Support ECU Assembly

No. 10 CAN Junction Connector Wiring Color Connect to
E174-5 (CANH) B Millimeter wave radar sensor assembly
E174-15 (CANL) P
E174-6 (CANH) R Forward recognition camera
E174-16 (CANL) P
E174-7 (CANH) W Driving support ECU assembly
E174-17 (CANL) P


k.
U165507E02
1.344,0.719 1.146,0.427 1.146,0.427 1.021,0.427 false 1.302,0.146 1.573,0.146 1.573,0.146 1.677,0.708 false 0.094,0 0.448,0.208 0.354,0.208 10 false *a 0.396,0.833 0.75,1.052 0.354,0.219 10 false K50 0.542,0.354 1.083,0.563 0.542,0.208 10 false CANH 0.865,0.063 1.417,0.24 0.552,0.177 10 false CANL

NO. 1 CAN JUNCTION TERMINAL

Text in Illustration
*a Rear view of wire harness connector
(to No. 1 CAN Junction Terminal)

No. 1 CAN Junction Terminal Wiring Color Connect to
K50-3 (CANH) SB No. 4 CAN junction connector
K50-2 (CANL) B


l.
U165508E02
1.344,0.708 1.146,0.417 1.146,0.417 1.021,0.417 false 1.292,0.146 1.563,0.146 1.563,0.146 1.667,0.708 false 0.094,0 0.375,0.198 0.281,0.198 10 false *a 0.396,0.833 0.771,1.021 0.375,0.188 10 false F98 0.531,0.333 1.083,0.542 0.552,0.208 10 false CANH 0.854,0.073 1.406,0.271 0.552,0.198 10 false CANL

NO. 2 CAN JUNCTION TERMINAL

Text in Illustration
*a Rear view of wire harness connector
(to No. 2 CAN Junction Terminal)

No. 2 CAN Junction Terminal Wiring Color Connect to
F98-3 (CANH) B No. 6 CAN junction connector
F98-2 (CANL) GR


m.
U164974E02
1.781,0.146 1.615,0.146 1.615,0.146 1.375,0.875 false 2.219,0.417 2.073,0.417 2.073,0.417 1.729,0.854 false 1.833,0.052 2.458,0.229 0.625,0.177 10 false CANH 0.542,0.906 0.885,1.083 0.344,0.177 10 false L69 0.104,0 0.313,0.177 0.208,0.177 10 false *a 2.281,0.313 2.844,0.51 0.563,0.198 10 false CANL

NO. 3 CAN JUNCTION TERMINAL

Text in Illustration
*a Rear view of wire harness connector
(to No. 3 CAN Junction Terminal)

No. 3 CAN Junction Terminal Wiring Color Connect to
L69-3 (CANH) W No. 9 CAN junction connector
L69-2 (CANL) L



CHECK DLC3


a.
U156301E04
1.594,0.896 1.396,0.406 1.396,0.406 1.271,0.406 false 1.948,0.896 2.135,0.406 2.135,0.406 2.271,0.406 false 2.333,1.469 2.479,1.896 2.479,1.896 2.615,1.896 false 1.969,1.469 1.823,1.896 1.823,1.896 1.688,1.896 false 0.052,0 0.219,0.188 0.167,0.188 10 false *a 2.333,0.323 2.99,0.531 0.656,0.208 10 false CANH 0.948,0.323 1.417,0.531 0.469,0.208 10 false CG 1.229,1.823 1.771,2.021 0.542,0.198 10 false CANL 2.656,1.792 3.125,1.99 0.469,0.198 10 false BAT 0.313,0.385 0.708,0.583 0.396,0.198 10 false E22

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

Text in Illustration
*a Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E22-6 (CANH) - E22-14 (CANL) LG - W Cable disconnected from negative (-) battery terminal 54 to 66 Ω
E22-6 (CANH) - E22-4 (CG) LG - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E22-14 (CANL) - E22-4 (CG) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E22-6 (CANH) - E22-16 (BAT) LG - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E22-14 (CANL) - E22-16 (BAT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CENTRAL GATEWAY ECU


U165609E01
0.131,0.052 0.737,0.302 0.606,0.250 10 *a 1.625,1.347 1.972,1.489 0.346,0.143 10 E145 2.274,0.616 2.857,0.762 0.583,0.146 10 CA3H*B 2.807,0.427 3.390,0.572 0.583,0.146 10 CA3L*B 2.373,1.957 2.955,2.103 0.583,0.146 10 CA4H*A 2.59,2.171 3.172,2.317 0.583,0.146 10 CA4L*A 3.826,0.427 4.409,0.572 0.583,0.146 10 CA6H*D 4.316,0.623 4.899,0.769 0.583,0.146 10 CA6L*D 4.422,1.957 5.004,2.103 0.583,0.146 10 CA5H*C 4.211,2.174 4.794,2.320 0.583,0.146 10 CA5L*C 2.965,1.335 2.518,0.903 2.518,0.903 2.336,0.903 false 4.219,1.335 4.667,0.903 4.667,0.903 4.849,0.903 false 3.548,1.456 3.157,2.035 3.157,2.035 2.926,2.035 false 3.623,1.456 3.357,2.234 3.357,2.234 3.125,2.234 false 3.771,1.456 4.162,2.035 4.162,2.035 4.393,2.035 false 3.696,1.456 3.963,2.234 3.963,2.234 4.194,2.234 false 3.832,1.434 3.663,0.497 3.663,0.497 3.789,0.497 false 3.884,1.341 4.206,0.686 4.206,0.686 4.297,0.686 false 3.307,1.434 3.476,0.497 3.476,0.497 3.35,0.497 false 3.255,1.341 2.933,0.686 2.933,0.686 2.842,0.686 false 1.991,0.843 2.574,0.989 0.583,0.146 10 GND 4.87,0.829 5.453,0.975 0.583,0.146 10 BATT

Text in Illustration
*A Bus 2 *B Bus 3
*C Bus 5 *D V Bus
*a Component without harness connected
(Central Gateway ECU)
- -

a.
U165595E01
0.051,0.021 0.221,0.174 0.170,0.153 10 *a 1.416,0.175 1.763,0.314 0.347,0.139 10 E145 2.423,1.67 3.065,1.821 0.642,0.151 10 CA4H*A 2.19,1.846 2.832,1.997 0.642,0.151 10 CA4L*A 1.78,1.197 2.284,1.773 2.284,1.773 2.398,1.773 false 2.172,1.93 1.983,1.93 1.983,1.93 1.646,1.197 false 1.389,1.197 1.057,2.042 1.057,2.042 0.942,2.042 false 1.383,2.039 1.246,2.039 1.246,2.039 1.522,1.197 false 2.185,1.125 2,0.109 2,0.109 2.22,0.109 false 2.289,0.895 2.205,0.269 2.205,0.269 2.36,0.269 false 2.375,0.19 2.920,0.341 0.545,0.151 10 CA3H*B 2.241,0.006 2.786,0.157 0.545,0.151 10 CA3L*B 0.235,1.928 0.780,2.080 0.545,0.151 10 CA5H*C 0.333,1.671 0.877,1.822 0.545,0.151 10 BATT 1.418,1.963 1.963,2.114 0.545,0.151 10 CA5L*C 1.031,0.152 1.2,0.152 1.2,0.152 1.243,1.113 false 0.344,0.058 0.889,0.209 0.545,0.151 10 CA6H*D 0.072,0.296 0.617,0.447 0.545,0.151 10 CA6L*D 2.947,0.899 2.833,0.418 2.833,0.418 2.987,0.418 false 3.002,0.339 3.343,0.490 0.341,0.151 10 GND 0.461,0.988 0.203,1.767 0.203,1.767 0.309,1.767 false

Disconnect the central gateway ECU connector.

Text in Illustration
*A Bus 2
*B Bus 3
*C Bus 5
*D V Bus
*a Front view of wire harness connector
(to Central Gateway ECU)


b.

Measure the resistance according to the value(s) in the table below.

Bus 2
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E145-18 (CA4H) - E145-17 (CA4L) L - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E145-18 (CA4H) - E145-10 (GND) L - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-17 (CA4L) - E145-10 (GND) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-18 (CA4H) - E145-1 (BATT) L - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E145-17 (CA4L) - E145-1 (BATT) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 3
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E145-6 (CA3H) - E145-21 (CA3L) R - GR Cable disconnected from negative (-) battery terminal 108 to 132 Ω
E145-6 (CA3H) - E145-10 (GND) R - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-21 (CA3L) - E145-10 (GND) GR - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-6 (CA3H) - E145-1 (BATT) R - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E145-21 (CA3L) - E145-1 (BATT) GR - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E145-15 (CA5H) - E145-16 (CA5L) SB - B Cable disconnected from negative (-) battery terminal 108 to 132 Ω
E145-15 (CA5H) - E145-10 (GND) SB - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-16 (CA5L) - E145-10 (GND) B - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-15 (CA5H) - E145-1 (BATT) SB - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E145-16 (CA5L) - E145-1 (BATT) B - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher

V Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E145-14 (CA6H) - E145-10 (GND) LG - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-5 (CA6L) - E145-10 (GND) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-14 (CA6H) - E145-1 (BATT) LG - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E145-5 (CA6L) - E145-1 (BATT) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM


U164557E02
4.594,1.719 4.063,2.313 4.063,2.313 3.99,2.313 false 4.594,1.844 4.469,2.563 4.469,2.563 4.396,2.563 false 4.604,1.094 4.344,0.438 4.344,0.438 4.281,0.438 false 4.729,1.094 4.552,0.198 4.552,0.198 4.49,0.198 false 4.573,1.25 4.073,0.729 4.073,0.729 4.01,0.729 false 0.208,0.094 0.417,0.302 0.208,0.208 10 false *a 3.792,2.479 4.438,2.656 0.646,0.177 10 false CANL*C 3.365,2.219 4.042,2.406 0.677,0.188 10 false CANH*C 3.073,0.354 4.396,0.552 1.323,0.198 10 false CANL*A, CANH*B 3.875,0.094 4.552,0.302 0.677,0.208 10 false CANH*A 5.167,0.542 5.552,0.74 0.385,0.198 10 false A38 3.427,0.646 4.125,0.823 0.698,0.177 10 false CANL*B

Text in Illustration
*A for 1UR-FE, 1GR-FE *B for 3UR-FE
*C for 1VD-FTV - -
*a Component without harness connected
(ECM)
- -

a.

Disconnect the ECM connectors.

U165114E01
2.008,0.608 2.275,0.750 0.267,0.142 10 A38 6.546,1.44 6.827,1.582 0.281,0.142 10 C45 0.099,0.078 0.364,0.220 0.265,0.142 10 *a 1.498,0.742 1.564,0.742 1.564,0.742 1.884,1.199 false 0.744,0.669 1.499,0.811 0.755,0.142 10 BATT*A, *B 2.788,1.305 3.285,0.78 3.285,0.78 3.39,0.78 false 3.404,0.713 4.796,0.855 1.392,0.142 10 CANL*B 2.781,1.197 3.001,0.563 3.001,0.563 3.106,0.563 false 3.119,0.495 4.511,0.637 1.392,0.142 10 CANL*A, CANH*B 2.697,1.197 2.755,0.327 2.755,0.327 2.86,0.327 false 2.874,0.26 3.582,0.402 0.708,0.142 10 CANH*A 4.984,2.183 5.061,2.183 5.061,2.183 5.229,1.682 false 4.771,2.123 5.035,2.265 0.264,0.142 10 E1 3.337,2.105 3.952,2.247 0.615,0.142 10 CANH*C 2.773,1.647 3.219,2.177 3.219,2.177 3.326,2.177 false 3.047,2.346 3.644,2.488 0.596,0.142 10 CANL*C 2.771,1.727 2.929,2.418 2.929,2.418 3.037,2.418 false 1.179,0.982 1.246,0.982 1.246,0.982 1.87,1.344 false 0.639,0.908 1.182,1.050 0.544,0.142 10 BATT*C

Text in Illustration
*A for 1UR-FE, 1GR-FE *B for 3UR-FE
*C for 1VD-FTV - -
*a Front view of wire harness connector
(to ECM)
- -


b.

Measure the resistance according to the value(s) in the table below.

for 1UR-FE, 1GR-FE
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A38-10 (CANH) - A38-11 (CANL) V - W Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A38-10 (CANH) - C45-81 (E1) V - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-11 (CANL) - C45-81 (E1) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-10 (CANH) - A38-1 (BATT) V - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A38-11 (CANL) - A38-1 (BATT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for 3UR-FE
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A38-11 (CANH) - A38-19 (CANL) V - W Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A38-11 (CANH) - C45-81 (E1) V - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-19 (CANL) - C45-81 (E1) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-11 (CANH) - A38-1 (BATT) V - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A38-19 (CANL) - A38-1 (BATT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for 1VD-FTV
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A38-41 (CANH) - A38-49 (CANL) V - W Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A38-41 (CANH) - C45-81 (E1) V - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-49 (CANL) - C45-81 (E1) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-41 (CANH) - A38-20 (BATT) V - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A38-49 (CANL) - A38-20 (BATT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MASTER CYLINDER SOLENOID (SKID CONTROL ECU)


U164487E02
2.896,0.906 2.615,0.448 2.615,0.448 2.5,0.448 false 2.594,0.167 2.74,0.167 2.74,0.167 2.906,0.677 false 0.094,0.073 0.51,0.292 0.417,0.219 10 false *a 1.031,0.906 1.479,1.146 0.448,0.24 10 false A24 2.135,0.083 2.667,0.271 0.531,0.188 10 false CANH 2.073,0.354 2.604,0.552 0.531,0.198 10 false CANL

Text in Illustration
*a Component without harness connected
(Master Cylinder Solenoid [Skid Control ECU])
- -

a.
U156452E01
0.1,0.106 0.286,0.278 0.185,0.172 10 *a 1.266,0.254 1.538,0.391 0.272,0.137 10 A24 2.56,0.23 3.065,0.366 0.505,0.137 10 CANH 2.638,0.556 3.142,0.693 0.505,0.137 10 CANL 0.127,0.407 0.632,0.544 0.505,0.137 10 +BM1 0.028,0.678 0.533,0.815 0.505,0.137 10 GND1 2.178,1.099 2.464,0.626 2.464,0.626 2.605,0.626 false 2.519,0.312 2.343,0.312 2.343,0.312 2.143,1.014 false 0.994,1.013 0.783,0.497 0.783,0.497 0.594,0.497 false 0.517,0.738 0.633,0.738 0.633,0.738 0.846,1.013 false

Disconnect the master cylinder solenoid (skid control ECU) connector.

Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A24-11 (CANH) - A24-25 (CANL) L - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A24-11 (CANH) - A24-1 (GND1) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-25 (CANL) - A24-1 (GND1) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-11 (CANH) - A24-2 (+BM1) L - B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A24-25 (CANL) - A24-2 (+BM1) W - B Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


U156293E04
4.063,0.833 4.354,0.115 4.354,0.115 4.521,0.115 false 4.167,0.833 4.563,0.323 4.563,0.323 4.729,0.323 false 0.073,0.052 0.542,0.281 0.469,0.229 10 false *a 4.781,0.25 5.323,0.427 0.542,0.177 10 false CANH 4.563,0.031 5.198,0.24 0.635,0.208 10 false CANL 4.76,0.927 5.125,1.135 0.365,0.208 10 false E35

Text in Illustration
*a Component without harness connected
(Air Conditioning Amplifier Assembly)
- -

a.
U156515E04
2.115,3.208 2.313,3.104 2.313,3.104 2.427,3.104 false 0.948,3.01 1.208,3.01 1.208,3.01 1.427,3.208 false 1.865,1.063 2.292,0.781 2.292,0.781 2.542,0.781 false 2.365,0.406 2.198,0.406 2.198,0.406 1.75,1.052 false 0.104,0.052 0.354,0.25 0.25,0.198 10 false *a 0.51,3.313 0.938,3.521 0.427,0.208 10 false E36 2.469,3.01 3.021,3.208 0.552,0.198 10 false GND 0.604,2.917 1.01,3.104 0.406,0.188 10 false +B1 0.594,1.198 0.958,1.438 0.365,0.24 10 false E35 2.583,0.688 3.125,0.885 0.542,0.198 10 false CANH 2.406,0.323 2.969,0.531 0.563,0.208 10 false CANL

Disconnect the air conditioning amplifier assembly connectors.

Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Condition Specified Condition
E35-3 (CANH) - E35-4 (CANL) G - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E35-3 (CANH) - E36-1 (GND) G - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E35-4 (CANL) - E36-1 (GND) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E35-3 (CANH) - E36-6 (+B1) G - LG Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E35-4 (CANL) - E36-6 (+B1) W - LG Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COWL SIDE JUNCTION BLOCK LH AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U166538E02
1.625,0.635 1.625,0.396 1.625,0.396 1.708,0.396 false 1.615,1.458 1.865,1.458 false 1.615,1.813 1.865,1.813 false 2.438,4.021 2.896,3.563 2.896,3.563 3.063,3.563 false 2.854,3.313 2.688,3.313 2.688,3.313 2.344,4.021 false 4.823,4.021 5.396,3.479 5.396,3.479 5.51,3.479 false 5.344,3.271 5.198,3.271 5.198,3.271 4.74,4.021 false 0.875,1.26 1.25,1.458 0.375,0.198 10 false 2K 1.74,0.323 2.083,0.521 0.344,0.198 10 false *1 0.104,0.104 0.542,0.354 0.438,0.25 12 false *A 1.917,1.375 2.792,1.583 0.875,0.208 10 false E118 1.917,1.729 2.781,1.969 0.865,0.24 10 false E117 0.875,1.813 1.198,2.042 0.323,0.229 10 false 2H 0.885,2.229 1.229,2.417 0.344,0.188 10 false 2G 2.885,3.219 3.667,3.438 0.781,0.219 10 false CANN*B 3.104,3.469 3.854,3.708 0.75,0.24 10 false CANP*B 0.938,2.438 1.292,2.677 0.354,0.24 10 false 2F 3.76,0.99 4.094,1.198 0.333,0.208 10 false A 5.865,1.115 6.188,1.323 0.323,0.208 10 false 2J 5.875,1.781 6.198,1.979 0.323,0.198 10 false 2I 2,3.24 2.427,3.458 0.427,0.219 10 false E117 4.49,3.281 4.885,3.531 0.396,0.25 10 false E118 5.552,3.396 6.375,3.625 0.823,0.229 10 false CANL*A 5.385,3.167 6.177,3.365 0.792,0.198 10 false CANH*A 1.813,4.667 2.063,4.896 0.25,0.229 10 false 2I 5.594,4.667 5.938,4.885 0.344,0.219 10 false 2J 1.24,6.167 1.531,6.365 0.292,0.198 10 false 2H 3.781,6.167 4.135,6.375 0.354,0.208 10 false 2K 5.438,6.323 5.823,6.51 0.385,0.188 10 false 2G 6.438,6.323 6.75,6.542 0.313,0.219 10 false 2F 3.542,7.771 3.74,8.01 0.198,0.24 10 false A

Text in Illustration
*A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors *B Bus 2
*C Sub Bus 1 - -
*1 Main Body ECU (Multiplex Network Body ECU) - -

U166539E02
1.625,0.635 1.625,0.396 1.625,0.396 1.708,0.396 false 1.615,1.135 1.865,1.135 false 1.615,1.458 1.865,1.458 false 1.615,1.823 1.865,1.823 false 1.667,4.01 2.125,3.552 2.125,3.552 2.292,3.552 false 2.104,3.313 1.938,3.313 1.938,3.313 1.563,4.021 false 3.635,4.042 3.865,4.375 3.865,4.375 3.979,4.375 false 3.833,4.542 3.688,4.542 3.688,4.542 3.552,4.052 false 0.875,1.26 1.208,1.5 0.333,0.24 10 false 2K 1.906,1.052 2.792,1.25 0.885,0.198 10 false E137 1.74,0.26 2.094,0.479 0.354,0.219 10 false *1 0.104,0.104 0.542,0.354 0.438,0.25 12 false *A 1.906,1.375 2.781,1.646 0.875,0.271 10 false E118 1.906,1.75 2.771,1.979 0.865,0.229 10 false E117 0.875,1.802 1.25,2.021 0.375,0.219 10 false 2H 0.906,2.219 1.344,2.448 0.438,0.229 10 false 2G 2.146,3.219 2.865,3.438 0.719,0.219 10 false CANN*C 2.344,3.458 3.052,3.667 0.708,0.208 10 false CANP*C 0.938,2.438 1.333,2.635 0.396,0.198 10 false 2F 3.75,0.958 4.083,1.177 0.333,0.219 10 false A 5.865,1.135 6.219,1.354 0.354,0.219 10 false 2J 5.865,1.771 6.281,2.031 0.417,0.26 10 false 2I 1.333,3.24 1.771,3.479 0.438,0.24 10 false E117 3.604,3.24 4.083,3.469 0.479,0.229 10 false E118 5.719,3.24 6.177,3.479 0.458,0.24 10 false E137 4.021,4.292 4.813,4.49 0.792,0.198 10 false CANL*B 3.875,4.469 4.594,4.698 0.719,0.229 10 false CANH*B 1.813,4.667 2.063,4.927 0.25,0.26 10 false 2I 5.594,4.667 5.896,4.917 0.302,0.25 10 false 2J 1.25,6.167 1.542,6.406 0.292,0.24 10 false 2H 3.792,6.177 4.26,6.448 0.469,0.271 10 false 2K 5.438,6.313 5.781,6.542 0.344,0.229 10 false 2G 6.438,6.323 6.76,6.531 0.323,0.208 10 false 2F 3.531,7.781 3.865,8.104 0.333,0.323 10 false A

Text in Illustration
*A Main Body ECU (Multiplex Network Body ECU) with 3 Connectors *B Bus 2
*C Sub Bus 1 - -
*1 Main Body ECU (Multiplex Network Body ECU) - -

a.

Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL).

U165263E01
0.145,0.15 0.429,0.295 0.284,0.145 10 *a 4.283,0.15 4.566,0.295 0.284,0.145 10 *b 1.039,0.561 1.388,0.706 0.349,0.145 10 E118 2.772,0.561 3.120,0.706 0.349,0.145 10 E117 5.589,0.859 5.711,1.004 0.122,0.145 10 A 1.115,1.384 0.957,2.08 0.957,2.08 0.766,2.08 false 0.663,1.824 0.803,1.824 0.803,1.824 1.051,1.385 false 3.035,1.405 3.299,2.034 3.299,2.034 3.49,2.034 false 3.635,1.76 3.495,1.76 3.495,1.76 3.099,1.405 false 6.707,1.469 6.522,1.181 6.522,1.181 6.368,1.181 false 5.244,1.483 5.072,1.745 5.072,1.745 4.904,1.745 false 0.189,2.012 0.937,2.150 0.748,0.139 10 CANL*A 0.088,1.756 0.835,1.894 0.748,0.139 10 CANH*A 3.654,1.696 4.402,1.834 0.748,0.139 10 CANP*B 4.484,1.679 4.898,1.817 0.413,0.139 10 GND1 3.514,1.972 4.262,2.110 0.748,0.139 10 CANN*B 5.951,1.111 6.369,1.250 0.418,0.139 10 BECU

Text in Illustration
*A Bus 2 *B Sub Bus 1
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


b.

Reconnect the cowl side junction block LH connectors.


c.

Measure the resistance according to the value(s) in the table below.

Bus 2
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E118-14 (CANH) - E118-13 (CANL) G - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E118-14 (CANH) - A-11 (GND1) G - None Cable disconnected from negative (-) battery terminal 200 Ω or higher
E118-13 (CANL) - A-11 (GND1) W - None Cable disconnected from negative (-) battery terminal 200 Ω or higher
E118-14 (CANH) - A-31 (BECU) G - None Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E118-13 (CANL) - A-31 (BECU) W - None Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 1
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E117-9 (CANP) - E117-10 (CANN) GR - L Cable disconnected from negative (-) battery terminal 108 to 132 Ω
E117-9 (CANP) - A-11 (GND1) GR - None Cable disconnected from negative (-) battery terminal 200 Ω or higher
E117-10 (CANN) - A-11 (GND1) L - None Cable disconnected from negative (-) battery terminal 200 Ω or higher
E117-9 (CANP) - A-31 (BECU) GR - None Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E117-10 (CANN) - A-31 (BECU) L - None Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


U166092E01
3.444,0.282 3.788,0.423 0.343,0.141 10 E119 2.105,1.295 1.807,1.186 1.807,1.186 1.671,1.186 false 2.312,1.277 2.081,0.36 2.081,0.36 1.947,0.36 false 1.533,0.289 1.949,0.430 0.416,0.141 10 CANH 1.259,1.126 1.676,1.267 0.416,0.141 10 CANL 0.107,0.072 0.523,0.213 0.416,0.141 10 *a

Text in Illustration
*a Component without harness connected
(Combination Meter Assembly)
- -

a.
U165132E01
0.252,1.752 0.671,1.889 0.419,0.137 10 CANH 0.074,0.061 0.262,0.198 0.188,0.137 10 *a 2.945,1.372 3.201,1.510 0.257,0.137 10 B 2.567,1.264 2.792,1.454 2.792,1.454 2.92,1.454 false 0.14,1.372 0.550,1.510 0.409,0.137 10 CANL 0.978,1.264 0.752,1.454 0.752,1.454 0.624,1.454 false 0.364,0.862 0.773,1.000 0.409,0.137 10 ET 0.978,1.104 0.752,0.945 0.752,0.945 0.624,0.945 false 1.061,1.264 0.939,1.845 0.939,1.845 0.76,1.845 false 1.578,0.223 1.922,0.364 0.343,0.141 10 E119

Disconnect the combination meter assembly connector.

Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E119-39 (CANH) - E119-40 (CANL) BE - W Cable disconnected from negative (-) battery terminal 108 to 132 Ω
E119-39 (CANH) - E119-20 (ET) BE - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E119-40 (CANL) - E119-20 (ET) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E119-39 (CANH) - E119-21 (B) BE - V Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E119-40 (CANL) - E119-21 (B) W - V Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


U156197E01
4.28,0.722 4.084,0.722 4.084,0.722 3.678,1.328 false 3.782,1.606 4.059,2.021 4.059,2.021 4.217,2.021 false 3.254,0.625 3.522,0.762 0.268,0.137 10 E47 0.11,0.09 0.384,0.227 0.274,0.137 10 *a 4.318,0.652 4.752,0.789 0.435,0.137 10 CANH 4.234,1.961 4.748,2.098 0.514,0.137 10 CANL

Text in Illustration
*a Component without harness connected
(Airbag Sensor Assembly)
- -

a.
U156279E01
0.083,0.054 0.440,0.467 0.357,0.413 10 *a 0.083,1.975 0.440,2.388 0.357,0.413 10 *b 2.568,3.094 2.991,3.232 0.423,0.139 10 BAT 0.393,2.618 0.667,2.764 0.274,0.145 10 E22 0.482,0.946 0.756,1.091 0.274,0.145 10 E47 2.241,2.935 2.392,3.172 2.392,3.172 2.524,3.172 false 2.565,0.526 2.988,0.664 0.423,0.139 10 CANH 2.075,1.307 2.297,1.525 2.297,1.525 2.447,1.525 false 1.98,0.999 2.385,0.599 2.385,0.599 2.535,0.599 false 2.464,1.452 2.888,1.590 0.423,0.139 10 CANL 1.77,1.307 1.996,1.785 1.996,1.785 2.146,1.785 false 2.163,1.712 2.587,1.850 0.423,0.139 10 E1

Disconnect the airbag sensor assembly connector.

Text in Illustration
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E47-13 (CANH) - E47-22 (CANL) GR - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E47-13 (CANH) - E47-25 (E1) GR - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E47-22 (CANL) - E47-25 (E1) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E47-13 (CANH) - E22-16 (BAT) GR - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E47-22 (CANL) - E22-16 (BAT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY (for Multi-media Module Receiver Type)


U166548E01
1.854,0.795 2.113,0.933 0.259,0.138 10 F77 0.087,0.135 0.347,0.273 0.259,0.138 10 *a 3.04,1.445 3.364,1.131 3.364,1.131 3.525,1.131 false 3.31,0.9 3.11,0.9 3.11,0.9 2.941,1.442 false 3.318,0.842 3.880,0.980 0.563,0.138 10 CANL 3.544,1.068 4.107,1.206 0.563,0.138 10 CANH

Text in Illustration
*a Component without harness connected
(Multi-media Module Receiver Assembly)
- -

a.
U165484E01
0.454,1.11 0.537,1.989 0.537,1.989 0.709,1.989 false 2.81,0.591 2.682,0.591 2.682,0.591 2.842,1.02 false 0.916,1.741 0.787,1.741 0.787,1.741 0.551,1.11 false 0.939,1.664 1.361,1.801 0.422,0.137 10 CANL 0.738,1.915 1.160,2.052 0.422,0.137 10 CANH 0.054,0.044 0.477,0.182 0.422,0.137 10 *a 1.593,0.377 1.853,0.514 0.260,0.137 10 F77 2.836,0.51 3.105,0.647 0.269,0.137 10 +B1 2.476,1.787 2.348,1.787 2.348,1.787 2.106,1.097 false 2.499,1.71 2.921,1.847 0.422,0.137 10 GND1

Disconnect the multi-media module receiver assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F77-1 (CANH) - F77-2 (CANL) G - GR Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F77-1 (CANH) - F77-12 (GND1) G - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
F77-2 (CANL) - F77-12 (GND1) GR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
F77-1 (CANH) - F77-17 (+B1) G - V Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F77-2 (CANL) - F77-17 (+B1) GR - V Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


U166589E01
4.87,0.841 5.224,0.979 0.354,0.138 10 F124 4.88,1.388 4.501,0.76 4.501,0.76 4.417,0.76 false 4.218,0.963 4.358,0.963 4.358,0.963 4.786,1.377 false 3.97,0.69 4.414,0.828 0.444,0.138 10 CANH 3.795,0.893 4.239,1.032 0.444,0.138 10 CANL 0.117,0.105 0.561,0.243 0.444,0.138 10 *a

Text in Illustration
*a Component without harness connected
(Radio and Display Receiver Assembly)
- -

a.
U165439E01
1.562,1.815 1.899,1.952 0.337,0.137 10 F124 0.064,0.06 0.269,0.230 0.205,0.170 10 *a 2.234,0.904 2.52,0.592 2.52,0.592 2.625,0.592 false 1.599,1.152 1.351,1.459 1.351,1.459 1.246,1.459 false 0.743,1.384 1.154,1.522 0.411,0.139 10 GND1 2.654,0.5 3.146,0.638 0.492,0.139 10 +B1 1.562,0.205 1.899,0.342 0.337,0.137 10 F120 2.033,2.614 2.48,2.201 2.48,2.201 2.585,2.201 false 2.614,2.11 3.106,2.248 0.492,0.139 10 CANL 1.902,2.614 2.269,1.919 2.269,1.919 2.375,1.919 false 2.403,1.828 2.895,1.966 0.492,0.139 10 CANH

Disconnect the radio and display receiver assembly connectors.

Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F124-9 (CANH) - F124-10 (CANL) G - GR Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F124-9 (CANH) - F120-7 (GND1) G - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
F124-10 (CANL) - F120-7 (GND1) GR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
F124-9 (CANH) - F120-4 (+B1) G - V Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F124-10 (CANL) - F120-4 (+B1) GR - V Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK STEERING SENSOR


U165705E01
3.475,0.271 3.821,0.413 0.347,0.142 10 E121 3.972,0.271 4.474,0.413 0.502,0.142 10 *B 5.529,0.274 5.876,0.416 0.347,0.142 10 E163 6.026,0.274 6.234,0.416 0.208,0.142 10 *C 0.05,0.055 0.397,0.197 0.347,0.142 10 *a 0.328,0.696 1.149,1.008 0.821,0.312 10 CANH 1.482,1.067 0.906,0.761 0.906,0.761 0.771,0.761 false 0.911,0.444 1.032,0.444 1.032,0.444 1.639,1.067 false 0.498,0.374 0.931,0.686 0.433,0.312 10 CANL 2.541,0.691 3.363,1.003 0.821,0.312 10 CANH 5.876,1.058 6.456,0.76 6.456,0.76 6.592,0.762 false 6.456,0.443 6.334,0.441 6.334,0.441 5.719,1.056 false 3.696,1.062 3.12,0.757 3.12,0.757 2.984,0.757 false 3.124,0.439 3.246,0.439 3.246,0.439 3.853,1.062 false 2.712,0.37 3.144,0.682 0.433,0.312 10 CANL 6.499,0.383 7.029,0.695 0.530,0.312 10 CANH 6.618,0.701 7.051,1.013 0.433,0.312 10 CANL 1.328,0.276 1.675,0.418 0.347,0.142 10 E181 1.825,0.276 2.327,0.418 0.502,0.142 10 *A

Text in Illustration
*A w/o Variable Gear Ratio Steering System, w/o Entry and Start System *B w/o Variable Gear Ratio Steering System, w/ Entry and Start System
*C w/ Variable Gear Ratio Steering System - -
*a Component without harness connected
(Steering Sensor)
- -

a.

Disconnect the steering sensor connector.

C344582E01
1.302,0.417 1.802,0.667 0.5,0.25 3.417,0.417 3.917,0.667 0.5,0.25 5.5,0.417 6,0.667 0.5,0.25 0.917,2 1.083,2 1.083,2 1.26,1.688 false 1.948,1.667 2.031,2 2.031,2 2.135,2 false 1.604,1.542 1.083,0.917 1.083,0.917 0.917,0.917 false 1.417,1.531 0.896,1.135 0.896,1.135 0.729,1.135 false 3.635,1.542 3.115,0.917 3.115,0.917 2.948,0.917 false 3.49,1.542 2.969,1.146 2.969,1.146 2.802,1.146 false 3.083,2 3.24,2 3.24,2 3.333,1.677 false 4,1.667 4.146,2 4.146,2 4.25,2 false 6.073,1.625 6.281,1.792 6.281,1.792 6.385,1.792 false 5.083,1.792 5.219,1.792 5.219,1.792 5.417,1.625 false 5.75,1.51 5.229,0.885 5.229,0.885 5.063,0.885 false 5.583,1.51 5.063,1.115 5.063,1.115 4.896,1.115 false 0.448,0.823 1.063,1.021 0.615,0.198 10 false CANH 0.292,1.052 0.906,1.25 0.615,0.198 10 false CANL 0.49,1.927 1.104,2.125 0.615,0.198 10 false ESS 2.167,1.927 2.667,2.167 0.5,0.24 10 false BAT 1.396,0.458 1.802,0.656 0.406,0.198 10 false E181 1.854,0.458 2.177,0.667 0.323,0.208 10 false *A 2.479,0.833 3.094,1.031 0.615,0.198 10 false CANH 4.615,0.802 5.229,1 0.615,0.198 10 false CANH 2.354,1.063 2.969,1.26 0.615,0.198 10 false CANL 4.448,1.042 5.063,1.24 0.615,0.198 10 false CANL 2.688,1.927 3.302,2.125 0.615,0.198 10 false ESS 4.302,1.917 4.802,2.156 0.5,0.24 10 false BAT 6.438,1.708 6.938,1.948 0.5,0.24 10 false BAT 4.698,1.708 5.313,1.906 0.615,0.198 10 false ESS 3.51,0.469 3.917,0.667 0.406,0.198 10 false E121 5.594,0.469 6,0.667 0.406,0.198 10 false E163 3.969,0.458 4.292,0.667 0.323,0.208 10 false *B 6.052,0.458 6.375,0.667 0.323,0.208 10 false *C

Text in Illustration
*A w/o Variable Gear Ratio Steering System, w/o Entry and Start System *B w/o Variable Gear Ratio Steering System, w/ Entry and Start System
*C w/ Variable Gear Ratio Steering System - -
*a Front view of wire harness connector
(Steering Sensor)
- -


b.

Measure the resistance according to the value(s) in the table below.

w/o Variable Gear Ratio Steering System, w/o Entry and Start System
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E181-4 (CANH) - E181-3 (CANL) GR - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E181-4 (CANH) - E181-2 (ESS) GR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E181-3 (CANL) - E181-2 (ESS) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E181-4 (CANH) - E181-6 (BAT) GR - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E181-3 (CANL) - E181-6 (BAT) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher

w/o Variable Gear Ratio Steering System, w/ Entry and Start System
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E121-3 (CANH) - E121-2 (CANL) GR - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E121-3 (CANH) - E121-1 (ESS) GR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E121-2 (CANL) - E121-1 (ESS) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E121-3 (CANH) - E121-5 (BAT) GR - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E121-2 (CANL) - E121-5 (BAT) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher

w/ Variable Gear Ratio Steering System
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E163-3 (CANH) - E163-2 (CANL) GR - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E163-3 (CANH) - E163-1 (ESS) GR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E163-2 (CANL) - E163-1 (ESS) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E163-3 (CANH) - E163-5 (BAT) GR - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E163-2 (CANL) - E163-5 (BAT) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK 4WD CONTROL ECU


U156424E01
1.788,1.497 1.422,2.249 1.422,2.249 1.263,2.249 false 1.788,1.281 1.422,0.596 1.422,0.596 1.263,0.596 false 2.635,0.3 2.916,0.446 0.281,0.145 10 A27 0.82,0.517 1.343,0.663 0.522,0.145 10 CANH 0.875,2.183 1.397,2.328 0.522,0.145 10 CANL 0.088,0.048 0.369,0.194 0.281,0.145 10 *a

Text in Illustration
*a Component without harness connected
(4WD Control ECU)
- -

a.
U156427E01
0.104,0.127 0.286,0.350 0.181,0.223 10 *a 1.558,0.249 1.823,0.388 0.265,0.140 10 A27 1.558,2.318 1.823,2.458 0.265,0.140 10 A28 2.921,1.224 2.726,0.588 2.726,0.588 2.568,0.588 false 2.313,3.579 2.571,3.865 2.571,3.865 2.728,3.865 false 2.903,1.465 2.717,1.883 2.717,1.883 2.54,1.883 false 0.514,1.465 0.7,1.883 0.7,1.883 0.878,1.883 false 0.896,1.806 1.365,1.945 0.468,0.140 10 +B 2.031,1.806 2.499,1.945 0.468,0.140 10 CANL 2.744,3.777 3.212,3.916 0.468,0.140 10 GND 2.062,0.499 2.531,0.639 0.468,0.140 10 CANH

Disconnect the 4WD control ECU connectors.

Text in Illustration
*a Front view of wire harness connector
(to 4WD Control ECU)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A27-20 (CANH) - A27-40 (CANL) P - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A27-20 (CANH) - A28-10 (GND) P - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
A27-40 (CANL) - A28-10 (GND) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
A27-20 (CANH) - A27-21 (+B) P - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A27-40 (CANL) - A27-21 (+B) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK TIRE PRESSURE WARNING ECU (w/ Tire Pressure Warning System)


U165207E01
1.442,2.058 1.62,2.058 1.62,2.058 1.813,1.368 false 0.101,0.059 0.278,0.213 0.177,0.154 10 *a 1.043,0.157 1.299,0.297 0.255,0.140 10 L65 1.516,0.157 1.771,0.297 0.255,0.140 10 *A 2.019,0.157 2.274,0.297 0.255,0.140 10 L75 2.491,0.157 2.747,0.297 0.255,0.140 10 *B 1.617,1.368 1.29,1.82 1.29,1.82 1.157,1.82 false 0.894,1.995 1.362,2.132 0.468,0.137 10 CANH 0.652,1.738 1.120,1.876 0.468,0.137 10 CANL

Text in Illustration
*A w/o Front Antenna
*B w/ Front Antenna
*a Component without harness connected
(Tire Pressure Warning ECU)

a.
U165419E01
1.429,2.061 1.606,2.061 1.606,2.061 1.793,1.542 false 0.052,0.047 0.228,0.201 0.177,0.154 10 *a 1.589,0.344 1.845,0.484 0.255,0.140 10 L65 1.648,1.542 1.324,1.806 1.324,1.806 1.191,1.806 false 0.679,1.714 1.147,1.852 0.468,0.137 10 CANH 0.931,1.969 1.399,2.107 0.468,0.137 10 CANL 1.348,1.458 1.083,1.351 1.083,1.351 0.95,1.351 false 0.683,1.259 1.152,1.396 0.468,0.137 10 +B 2.079,1.458 2.344,1.351 2.344,1.351 2.477,1.351 false 2.501,1.259 2.969,1.396 0.468,0.137 10 GND

w/o Front Antenna:

Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU)

i.

Disconnect the tire pressure warning ECU connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
L65-9 (CANH) - L65-10 (CANL) R - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
L65-9 (CANH) - L65-12 (GND) R - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
L65-10 (CANL) - L65-12 (GND) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
L65-9 (CANH) - L65-7 (+B) R - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L65-10 (CANL) - L65-7 (+B) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



b.
U165411E02
1.458,1.948 1.635,1.948 1.635,1.948 1.823,1.427 false 1.677,1.427 1.354,1.698 1.354,1.698 1.219,1.698 false 2.198,2.906 2.406,3.146 2.406,3.146 2.531,3.146 false 2.104,1.344 2.375,1.24 2.375,1.24 2.5,1.24 false 0.083,0.094 0.479,0.323 0.396,0.229 10 false *a 0.083,1.938 0.5,2.135 0.417,0.198 10 false *b 0.438,2.594 0.823,2.781 0.385,0.188 10 false E22 1.583,0.292 2.042,0.5 0.458,0.208 10 false L75 0.698,1.604 1.313,1.802 0.615,0.198 10 false CANH 0.958,1.875 1.521,2.073 0.563,0.198 10 false CANL 2.594,3.052 3.104,3.26 0.51,0.208 10 false BAT 2.531,1.146 3.115,1.354 0.583,0.208 10 false GND

w/ Front Antenna:

Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU)
*b Front view DLC3

i.

Disconnect the tire pressure warning ECU connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
L75-9 (CANH) - L75-10 (CANL) R - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
L75-9 (CANH) - L75-12 (GND) R - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
L75-10 (CANL) - L75-12 (GND) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
L75-9 (CANH) - E22-16 (BAT) R - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L75-10 (CANL) - E22-16 (BAT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CHECK STEERING CONTROL ECU (w/ Variable Gear Ratio Steering System)


U165253E01
0.148,0.143 0.353,0.314 0.205,0.171 10 *a 4.859,0.381 5.202,0.521 0.343,0.140 10 E161 5.772,0.446 6.270,0.587 0.498,0.140 10 CNH1 5.252,1.374 5.65,0.52 5.65,0.52 5.744,0.52 false 5.225,1.573 5.573,2.267 5.573,2.267 5.723,2.267 false 5.744,2.188 6.242,2.328 0.498,0.140 10 CNL1

Text in Illustration
*a Component without harness connected
(Steering Control ECU)
- -

a.
U165186E01
1.457,0.987 1.177,1.31 1.177,1.31 0.979,1.31 false 0.458,1.226 0.890,1.362 0.432,0.137 10 PGND 0.327,1.855 0.734,1.992 0.408,0.137 10 CNH1 0.059,0.049 0.421,0.186 0.362,0.137 10 *a 2.377,1.662 2.728,1.799 0.351,0.137 10 E161 1.351,2.445 1.023,1.931 1.023,1.931 0.825,1.931 false 1.101,2.712 0.884,2.968 0.884,2.968 0.686,2.968 false 1.101,2.712 0.884,2.968 0.884,2.968 0.686,2.968 false 0.371,2.896 0.779,3.033 0.408,0.137 10 +BI 0.521,3.174 0.928,3.311 0.408,0.137 10 CNL1 1.351,2.712 1.203,3.266 1.203,3.266 1.005,3.266 false 0.487,0.648 0.838,0.785 0.351,0.137 10 E159

Disconnect the steering control ECU connectors.

Text in Illustration
*a Front view of wire harness connector
(to Steering Control ECU)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E161-3 (CNH1) - E161-9 (CNL1) R - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E161-3 (CNH1) - E159-1 (PGND) R - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E161-9 (CNL1) - E159-1 (PGND) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E161-3 (CNH1) - E161-7 (+BI) R - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E161-9 (CNL1) - E161-7 (+BI) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POWER STEERING ECU ASSEMBLY (w/ Variable Flow Control Solenoid Valve)


U164976E01
1.406,0.395 1.753,0.537 0.347,0.142 10 E102 0.118,0.112 0.465,0.254 0.347,0.142 10 *a 2.82,0.947 3.238,1.089 0.419,0.142 10 CANH 2.678,0.568 3.097,0.710 0.419,0.142 10 CANL 2.645,0.651 2.491,0.651 2.491,0.651 2.048,1.355 false 2.223,1.332 2.678,1.025 2.678,1.025 2.796,1.025 false

Text in Illustration
*a Component without harness connected
(Power Steering ECU Assembly)

a.
U164991E02
2.208,2.948 2.417,3.115 2.417,3.115 2.5,3.115 false 2.063,1.146 2.375,0.698 2.375,0.698 2.458,0.698 false 2.188,1.146 2.521,0.979 2.521,0.979 2.615,0.979 false 1.948,1.24 2.292,1.594 2.292,1.594 2.458,1.594 false 0.615,0.99 1.094,1.177 0.479,0.188 10 false E102 0.469,2.688 0.865,2.885 0.396,0.198 10 false E22 0.063,0.052 0.385,0.271 0.323,0.219 10 false *a 0.063,2 0.375,2.198 0.313,0.198 10 false *b 2.552,3.01 3.083,3.219 0.531,0.208 10 false BAT 2.635,0.896 3.219,1.104 0.583,0.208 10 false CANH 2.5,1.5 2.979,1.688 0.479,0.188 10 false GND 2.49,0.594 3.063,0.792 0.573,0.198 10 false CANL

Disconnect the power steering ECU assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E102-1 (CANH) - E102-2 (CANL) LG - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E102-1 (CANH) - E102-3 (GND) LG - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E102-2 (CANL) - E102-3 (GND) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E102-1 (CANH) - E22-16 (BAT) LG - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E102-2 (CANL) - E22-16 (BAT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


U164301E01
4.479,0.432 4.624,0.432 4.624,0.432 4.818,1.144 false 0.085,0.087 0.262,0.241 0.177,0.154 10 *a 5.086,0.366 5.431,0.506 0.346,0.140 10 E130 4.714,1.144 4.187,0.683 4.187,0.683 4.079,0.683 false 4.071,0.352 4.539,0.490 0.468,0.137 10 CANH 3.678,0.616 4.146,0.754 0.468,0.137 10 CANL

Text in Illustration
*a Component without harness connected
(Certification ECU [Smart Key ECU Assembly])
- -

a.
U165487E01
0.106,0.056 0.290,0.253 0.184,0.198 10 *a 1.502,0.305 1.860,0.454 0.357,0.149 10 E130 2.93,0.537 3.341,0.686 0.411,0.149 10 CANL 3.163,1.276 3.365,1.425 0.202,0.149 10 +B 2.773,0.308 3.220,0.457 0.448,0.149 10 CANH 2.531,1.039 2.761,0.623 2.761,0.623 2.91,0.623 false 2.75,0.391 2.535,0.391 2.535,0.391 2.379,1.045 false 0.759,1.314 0.581,1.552 0.581,1.552 0.452,1.552 false 2.824,1.121 3.002,1.359 3.002,1.359 3.131,1.359 false 0.289,1.488 0.492,1.637 0.202,0.149 10 E

Disconnect the certification ECU (smart key ECU assembly) connector.

Text in Illustration
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E130-7 (CANH) - E130-8 (CANL) B - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E130-7 (CANH) - E130-11 (E) B - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E130-8 (CANL) - E130-11 (E) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E130-7 (CANH) - E130-10 (+B) B - P Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E130-8 (CANL) - E130-10 (+B) W - P Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK HEADLIGHT SWIVEL ECU ASSEMBLY (w/ Automatic High Beam System)


U166545E01
3.337,0.144 3.684,0.286 0.347,0.142 10 E101 0.099,0.064 0.446,0.206 0.347,0.142 10 *a 1.448,0.205 1.891,0.347 0.443,0.142 10 CANL 1.864,0.269 1.991,0.269 1.991,0.269 2.479,0.683 false 1.864,0.269 1.991,0.269 1.991,0.269 2.479,0.683 false 1.765,0.041 2.208,0.183 0.443,0.142 10 CANH 2.216,0.105 2.342,0.105 2.342,0.105 2.602,0.679 false

Text in Illustration
*a Component without harness connected
(Headlight Swivel ECU Assembly)
- -

a.
U165703E01
0.853,0.178 1.200,0.320 0.347,0.142 10 E101 0.07,0.064 0.417,0.206 0.347,0.142 10 *a 0.07,1.751 0.417,1.893 0.347,0.142 10 *b 1.732,0.081 2.505,0.223 0.773,0.142 10 CANL 1.615,0.319 2.436,0.631 0.821,0.312 10 CANH 2.258,0.16 2.412,0.16 2.412,0.16 2.82,0.899 false 2.679,0.876 2.276,0.399 2.276,0.399 2.159,0.399 false 1.594,1.816 1.860,1.958 0.266,0.142 10 E22 2.591,2.945 2.910,3.087 0.319,0.142 10 BAT 2.271,2.831 2.447,3.027 2.447,3.027 2.565,3.027 false 2.133,1.481 2.452,1.623 0.319,0.142 10 E1 1.626,1.141 1.989,1.564 1.989,1.564 2.106,1.564 false

Disconnect the headlight swivel ECU assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E101-12 (CANH) - E101-13 (CANL) LG - B Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E101-12 (CANH) - E101-22 (E1) LG - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E101-13 (CANL) - E101-22 (E1) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E101-12 (CANH) - E22-16 (BAT) LG - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E101-13 (CANL) - E22-16 (BAT) B - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK HEADLIGHT LEVELING ECU ASSEMBLY (w/o Automatic High Beam System)


U165450E01
3.185,0.945 2.718,0.598 2.718,0.598 2.583,0.598 false 2.793,0.411 2.966,0.411 2.966,0.411 3.272,0.926 false 3.441,0.299 3.786,0.441 0.346,0.142 10 E109 2.166,0.528 2.595,0.670 0.429,0.142 10 CANL 2.357,0.336 2.786,0.478 0.429,0.142 10 CANH 0.126,0.084 0.472,0.226 0.346,0.142 10 *a

Text in Illustration
*a Component without harness connected
(Headlight Leveling ECU Assembly)
- -

a.
U165451E01
2.935,0.487 3.323,0.629 0.389,0.142 10 CANL 2.733,0.143 3.180,0.285 0.448,0.142 10 CANH 2.385,0.951 2.784,0.564 2.784,0.564 2.888,0.564 false 2.698,0.233 2.514,0.233 2.514,0.233 2.247,0.951 false 2.617,3.001 3.064,3.143 0.448,0.142 10 BAT 2.217,2.829 2.428,3.078 2.428,3.078 2.57,3.078 false 0.073,0.096 0.267,0.238 0.194,0.142 10 *a 1.361,0.232 1.704,0.374 0.343,0.142 10 E109 0.077,1.802 0.271,1.944 0.194,0.142 10 *b 0.318,2.514 0.588,2.656 0.270,0.142 10 E22 3.055,1.192 3.291,1.334 0.236,0.142 10 E1 2.64,1.05 2.866,1.269 2.866,1.269 3.008,1.269 false

Disconnect the headlight leveling ECU assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E109-6 (CANH) - E109-7 (CANL) LG - B Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E109-6 (CANH) - E109-9 (E1) LG - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E109-7 (CANL) - E109-9 (E1) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E109-6 (CANH) - E22-16 (BAT) LG - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E109-7 (CANL) - E22-16 (BAT) B - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK PARKING ASSIST ECU (w/ Multi-terrain Monitor System)


U166302E01
3.196,0.329 3.460,0.467 0.264,0.138 10 F76 3.189,1.491 3.625,1.630 0.436,0.139 10 CANL 0.163,0.104 0.408,0.306 0.246,0.202 10 *a 1.883,1.491 2.319,1.630 0.436,0.139 10 CANH 2.718,1.082 2.445,1.551 2.445,1.551 2.315,1.551 false 2.763,1.082 3.037,1.551 3.037,1.551 3.166,1.551 false

Text in Illustration
*a Component without harness connected
(Parking Assist ECU)
- -

a.
U165665E01
0.698,2.955 0.876,2.955 0.876,2.955 1.062,2.436 false 0.086,0.039 0.263,0.192 0.177,0.154 10 *a 2.453,0.232 2.716,0.372 0.262,0.140 10 F75 1.004,2.436 0.68,2.7 0.68,2.7 0.547,2.7 false 0.034,2.612 0.503,2.750 0.468,0.137 10 CANH 0.192,2.876 0.660,3.013 0.468,0.137 10 CANL 1.239,0.871 0.975,0.764 0.975,0.764 0.842,0.764 false 2.673,0.679 3.141,0.816 0.468,0.137 10 +B 2.221,0.861 2.485,0.753 2.485,0.753 2.618,0.753 false 0.348,0.687 0.816,0.825 0.468,0.137 10 GND1 2.836,2.218 3.098,2.357 0.262,0.140 10 F76

Disconnect the parking assist ECU connectors.

Text in Illustration
*a Rear view of wire harness connector
(to Parking Assist ECU)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F76-40 (CANH) - F76-39 (CANL) P - B Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F76-40 (CANH) - F75-4 (GND1) P - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
F76-39 (CANL) - F75-4 (GND1) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
F76-40 (CANH) - F75-1 (+B) P - G Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F76-39 (CANL) - F75-1 (+B) B - G Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)


U165225E01
2.106,0.89 1.773,0.522 1.773,0.522 1.615,0.522 false 1.783,0.287 1.979,0.287 1.979,0.287 2.201,0.895 false 3.477,0.347 3.743,0.485 0.266,0.137 10 F92 0.106,0.093 0.380,0.231 0.274,0.137 10 *a 1.548,0.216 2.062,0.353 0.514,0.137 10 R1 1.392,0.462 1.836,0.600 0.444,0.137 10 R2

Text in Illustration
*a Component without harness connected
(Clearance Warning ECU Assembly)
- -

a.
U165210E01
0.768,0.827 0.906,0.827 0.906,0.827 1.043,0.93 false 1.099,0.923 1.009,0.52 1.009,0.52 0.816,0.52 false 2.206,1.465 1.966,1.465 1.966,1.465 1.72,1.028 false 0.091,0.037 0.365,0.174 0.274,0.137 10 *a 0.091,1.881 0.365,2.019 0.274,0.137 10 *b 2.228,1.396 2.672,1.533 0.444,0.137 10 E 1.611,0.199 1.870,0.337 0.259,0.137 10 F92 0.458,2.597 0.724,2.734 0.266,0.137 10 E22 2.553,3.111 2.312,3.111 2.312,3.111 2.212,2.852 false 2.574,3.042 3.018,3.180 0.444,0.137 10 BAT 0.589,0.447 0.839,0.584 0.250,0.137 10 R1 0.509,0.738 0.726,0.875 0.217,0.137 10 R2

Disconnect the clearance warning ECU assembly connector.

Text in Illustration
*a Rear view of wire harness connector
(to Clearance Warning ECU Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F92-17 (R1) - F92-18 (R2) V - B Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F92-17 (R1) - F92-30 (E) V - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
F92-18 (R2) - F92-30 (E) B- BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
F92-17 (R1) - E22-16 (BAT) V - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F92-18 (R2) - E22-16 (BAT) B- L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)


U165622E02
2.458,0.333 2.604,0.333 2.604,0.333 2.844,0.823 false 2.729,0.823 2.458,0.542 2.458,0.542 2.354,0.542 false 3.344,0.333 3.198,0.333 3.198,0.333 2.958,0.823 false 3.073,0.823 3.344,0.542 3.344,0.542 3.448,0.542 false 0.125,0.042 0.573,0.24 0.448,0.198 10 false *a 1.677,0.844 2.208,1.063 0.531,0.219 10 false E164 3.479,0.458 4.135,0.635 0.656,0.177 10 false CA1P*B 3.396,0.229 4.125,0.417 0.729,0.188 10 false CA1N*B 1.885,0.24 2.573,0.438 0.688,0.198 10 false CA2H*A 1.792,0.448 2.427,0.625 0.635,0.177 10 false CA2L*A

Text in Illustration
*A Bus 5 *B Local Bus
*a Component without harness connected
(Driving Support ECU Assembly)
- -

a.
U165664E01
0.079,1.77 0.256,1.924 0.177,0.154 10 *b 0.079,0.086 0.256,0.239 0.177,0.154 10 *a 0.6,0.207 0.956,0.346 0.356,0.140 10 E164 2.072,0.232 2.25,0.232 2.25,0.232 2.324,0.944 false 2.197,0.944 2.109,0.444 2.109,0.444 1.976,0.444 false 2.676,0.232 2.499,0.232 2.499,0.232 2.424,0.944 false 2.551,0.944 2.64,0.444 2.64,0.444 2.773,0.444 false 2.786,0.356 3.317,0.493 0.531,0.137 10 CA2L*A 2.712,0.136 3.275,0.274 0.562,0.137 10 CA2H*A 1.407,0.137 1.962,0.274 0.555,0.137 10 CA1N*B 1.277,0.373 1.839,0.510 0.562,0.137 10 CA1P*B 2.313,1.209 2.642,1.634 2.642,1.634 2.775,1.634 false 2.799,1.543 3.267,1.680 0.468,0.137 10 GND 0.318,2.527 0.584,2.667 0.266,0.140 10 E22 2.27,2.83 2.47,3.095 2.47,3.095 2.603,3.095 false 2.627,3.003 3.095,3.141 0.468,0.137 10 BAT

Disconnect the driving support ECU assembly connector.

Text in Illustration
*A Bus 5
*B Local Bus
*a Front view of wire harness connector
(to Driving Support ECU Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Bus 5
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E164-10 (CA2H) - E164-11 (CA2L) L - B Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E164-10 (CA2H) - E164-28 (GND) L - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E164-11 (CA2L) - E164-28 (GND) B - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E164-10 (CA2H) - E22-16 (BAT) L - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E164-11 (CA2L) - E22-16 (BAT) B - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Local Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E164-8 (CA1P) - E164-9 (CA1N) W - P Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E164-8 (CA1P) - E164-28 (GND) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E164-9 (CA1N) - E164-28 (GND) P - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E164-8 (CA1P) - E22-16 (BAT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E164-9 (CA1N) - E22-16 (BAT) P - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)


U166508E01
0.088,0.076 0.265,0.230 0.177,0.154 10 *a 2.296,0.875 2.575,1.015 0.279,0.140 10 A72 4.223,1.6 4.788,1.737 0.566,0.137 10 CA1N*B 4.439,0.344 5.011,0.481 0.571,0.137 10 CA2L*A 4.18,0.075 4.752,0.212 0.571,0.137 10 CA2H*A 3.874,1.058 4.15,1.347 4.15,1.347 4.393,1.347 false 4.199,1.665 4.026,1.665 4.026,1.665 3.681,1.076 false 3.723,0.799 4.164,0.418 4.164,0.418 4.407,0.418 false 4.145,0.144 3.972,0.144 3.972,0.144 3.53,0.781 false 4.415,1.277 4.980,1.414 0.566,0.137 10 CA1P*B

Text in Illustration
*A Bus 5 *B Local Bus
*a Component without harness connected
(Millimeter Wave Radar Sensor Assembly)
- -

a.
U165662E02
1.594,0.823 1.229,0.417 1.229,0.417 1.063,0.417 false 1.365,0.177 1.563,0.177 1.563,0.177 1.771,0.823 false 1.479,1.031 1.094,1.333 1.094,1.333 0.927,1.333 false 1.323,1.583 1.531,1.583 1.531,1.583 1.635,1.031 false 2.292,2.76 2.531,2.99 2.531,2.99 2.708,2.99 false 0.896,0.656 1.01,0.656 1.01,0.656 1.458,0.865 false 0.115,1.615 0.479,1.823 0.365,0.208 10 false *b 0.115,0.052 0.531,0.25 0.417,0.198 10 false *a 2.75,0.854 3.146,1.052 0.396,0.198 10 false A72 0.625,1.5 1.344,1.708 0.719,0.208 10 false CA1N*B 0.25,1.25 0.938,1.448 0.688,0.198 10 false CA1P*B 0.448,0.344 1.135,0.521 0.688,0.177 10 false CA2L*A 0.375,0.594 0.927,0.938 0.552,0.344 10 false SGND 0.698,0.083 1.469,0.323 0.771,0.24 10 false CA2H*A 0.344,2.438 0.802,2.656 0.458,0.219 10 false E22 2.771,2.906 3.25,3.125 0.479,0.219 10 false BAT

Disconnect the millimeter wave radar sensor assembly connector.

Text in Illustration
*A Bus 5
*B Local Bus
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Bus 5
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A72-3 (CA2H) - A72-2 (CA2L) L - B Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A72-3 (CA2H) - A72-1 (SGND) L - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
A72-2 (CA2L) - A72-1 (SGND) B - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
A72-3 (CA2H) - E22-16 (BAT) L - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A72-2 (CA2L) - E22-16 (BAT) B - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Local Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A72-5 (CA1P) - A72-6 (CA1N) B - P Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A72-5 (CA1P) - A72-1 (SGND) B - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
A72-6 (CA1N) - A72-1 (SGND) P - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
A72-5 (CA1P) - E22-16 (BAT) B - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A72-6 (CA1N) - E22-16 (BAT) P - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK FORWARD RECOGNITION CAMERA (w/ Pre-crash Safety System)


U165623E01
0.06,0.067 0.237,0.221 0.177,0.154 10 *a 1.539,0.257 1.812,0.396 0.273,0.140 10 R20 1.503,1.286 1.164,1.84 1.164,1.84 0.95,1.84 false 0.885,1.518 1.01,1.518 1.01,1.518 1.338,1.286 false 1.503,0.972 1.164,0.418 1.164,0.418 0.95,0.418 false 0.885,0.74 1.01,0.74 1.01,0.74 1.338,0.972 false 0.188,1.439 0.753,1.577 0.566,0.137 10 CANL*B 0.188,0.675 0.753,0.812 0.566,0.137 10 CANH*B 0.252,0.345 0.818,0.483 0.566,0.137 10 CA1P*A 0.252,1.759 0.818,1.896 0.566,0.137 10 CA1N*A 1.503,1.286 1.164,1.84 1.164,1.84 0.95,1.84 false 0.885,1.518 1.01,1.518 1.01,1.518 1.338,1.286 false 1.503,0.972 1.164,0.418 1.164,0.418 0.95,0.418 false 0.885,0.74 1.01,0.74 1.01,0.74 1.338,0.972 false

Text in Illustration
*A Bus 5
*B Local Bus
*a Component without harness connected
(Forward Recognition Camera)

a.
U165412E01
2.082,1.435 2.231,1.582 2.231,1.582 2.382,1.582 false 1.947,1.43 2.185,1.875 2.185,1.875 2.34,1.875 false 2.082,1.132 2.231,0.986 2.231,0.986 2.382,0.986 false 1.947,1.138 2.185,0.573 2.185,0.573 2.34,0.573 false 2.402,0.912 3.001,1.049 0.599,0.137 10 CANH*B 2.402,1.514 3.001,1.651 0.599,0.137 10 CANL*B 0.97,1.663 1.569,1.800 0.599,0.137 10 GND 2.362,0.494 2.910,0.631 0.548,0.137 10 CA1P*A 2.362,1.803 2.910,1.940 0.548,0.137 10 CA1N*A 0.058,0.06 0.500,0.197 0.442,0.137 10 *a 0.545,1.144 0.819,1.281 0.275,0.137 10 R20 0.058,1.939 0.500,2.076 0.442,0.137 10 *b 0.421,2.609 0.688,2.746 0.268,0.137 10 E22 2.208,2.919 2.371,3.211 2.371,3.211 2.526,3.211 false 2.548,3.132 2.937,3.269 0.389,0.137 10 BAT 1.79,1.433 1.518,1.757 1.518,1.757 1.377,1.757 false

Disconnect the forward recognition camera connector.

Text in Illustration
*A Bus 5
*B Local Bus
*a Front view of wire harness connector
(to Forward Recognition Camera)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Bus 5
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
R20-5 (CA1P) - R20-11 (CA1N) G - B Cable disconnected from negative (-) battery terminal 54 to 69 Ω
R20-5 (CA1P) - R20-10 (GND) G - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
R20-11 (CA1N) - R20-10 (GND) B - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
R20-5 (CA1P) - E22-16 (BAT) G - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R20-11 (CA1N) - E22-16 (BAT) B - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Local Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
R20-6 (CANH) - R20-12 (CANL) R - P Cable disconnected from negative (-) battery terminal 108 to 132 Ω
R20-6 (CANH) - R20-10 (GND) R - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
R20-12 (CANL) - R20-10 (GND) P - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
R20-6 (CANH) - E22-16 (BAT) R - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R20-12 (CANL) - E22-16 (BAT) P - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK INNER REAR VIEW MIRROR ASSEMBLY (w/o Pre-crash Safety System, w/ Automatic High Beam System)


U165578E01
3.073,2.396 3.218,2.396 3.218,2.396 3.423,1.604 false 0.107,0.039 0.284,0.192 0.177,0.154 10 *a 3.471,0.344 3.743,0.484 0.273,0.140 10 R16 3.249,1.604 2.764,2.18 2.764,2.18 2.656,2.18 false 2.623,2.325 3.092,2.462 0.468,0.137 10 CANH 2.247,2.116 2.716,2.253 0.468,0.137 10 CANL

Text in Illustration
*a Component without harness connected
(Inner Rear View Mirror Assembly)
- -

a.
U165752E02
2.031,1.354 2.323,1.531 2.323,1.531 2.458,1.531 false 2.333,1.885 2.125,1.885 2.125,1.885 1.865,1.354 false 1.51,1.031 1.198,0.719 1.198,0.719 1.031,0.719 false 2.698,2.979 2.573,2.979 2.573,2.979 2.281,2.844 false 2.479,1.438 3.052,1.615 0.573,0.177 10 false CANL 2.344,1.792 3.167,2.063 0.823,0.271 10 false CANH 0.115,0.063 0.604,0.292 0.49,0.229 10 false *a 0.115,1.948 0.552,2.146 0.438,0.198 10 false *b 0.594,1.083 1.052,1.281 0.458,0.198 10 false R16 0.854,0.646 1.323,0.792 0.469,0.146 10 false E 0.385,2.583 0.813,2.771 0.427,0.188 10 false E22 2.729,2.885 3.229,3.104 0.5,0.219 10 false BAT

Disconnect the inner rear view mirror assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Inner Rear View Mirror Assembly)
*b Front view of DLC3

Text in Illustration
*a Front view of wire harness connector
(to Inner Rear View Mirror Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
R16-9 (CANH) - R16-10 (CANL) G - B Cable disconnected from negative (-) battery terminal 54 to 69 Ω
R16-9 (CANH) - R16-2 (E) G - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
R16-10 (CANL) - R16-2 (E) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
R16-9 (CANH) - E22-16 (BAT) G - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R16-10 (CANL) - E22-16 (BAT) B - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


U166225E01
2.425,0.837 2.579,0.993 0.153,0.156 10 r2 0.084,0.037 0.326,0.193 0.242,0.156 10 *a 4.448,0.405 4.954,0.560 0.506,0.156 10 CA1P 4.448,1.252 4.954,1.408 0.506,0.156 10 CA1N 3.82,1.006 4.188,1.314 4.188,1.314 4.429,1.314 false 3.82,0.793 4.188,0.484 4.188,0.484 4.429,0.484 false

Text in Illustration
*a Component without harness connected
(Blind Spot Monitor Sensor LH)
- -

a.
U165413E01
1.571,1.039 1.173,0.656 1.173,0.656 1.022,0.656 false 1.571,1.206 1.173,1.589 1.173,1.589 1.022,1.589 false 0.542,0.585 0.922,0.722 0.380,0.137 10 CA1P 0.531,1.512 0.920,1.649 0.389,0.137 10 CA1N 0.05,0.106 0.492,0.243 0.442,0.137 10 *a 2.676,1.041 2.820,1.178 0.144,0.137 10 r2 0.05,1.985 0.492,2.122 0.442,0.137 10 *b 0.413,2.655 0.678,2.792 0.265,0.137 10 E22 2.216,2.965 2.38,3.256 2.38,3.256 2.535,3.256 false 2.557,3.178 2.945,3.315 0.389,0.137 10 BAT 1.95,1.227 2.114,1.518 2.114,1.518 2.268,1.518 false 2.291,1.439 2.712,1.576 0.421,0.137 10 BRGD

Disconnect the blind spot monitor sensor LH connector.

Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
r2-2 (CA1P) - r2-7 (CA1N) R - B Cable disconnected from negative (-) battery terminal 54 to 69 Ω
r2-2 (CA1P) - r2-10 (BRGD) R - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
r2-7 (CA1N) - r2-10 (BRGD) B - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
r2-2 (CA1P) - E22-16 (BAT) R - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
r2-7 (CA1N) - E22-16 (BAT) B - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK SUSPENSION CONTROL ECU (w/ Active Height Control Suspension)


U165246E01
5.714,1.597 6.001,1.893 6.001,1.893 6.159,1.893 false 5.947,2.154 5.751,2.154 5.751,2.154 5.605,1.592 false 5.033,0.642 5.299,0.779 0.266,0.137 10 K34 6.192,1.828 6.778,1.965 0.585,0.137 10 CANH 5.964,2.098 6.470,2.235 0.506,0.137 10 CANL 4.945,1.688 4.945,1.834 false

Text in Illustration
*a Component without harness connected
(Suspension Control ECU)
- -

a.
U164987E01
0.048,0.032 0.238,0.260 0.191,0.228 10 *a 2.686,0.677 3.069,0.843 0.383,0.167 10 BAT2 2.188,1.219 2.59,0.751 2.59,0.751 2.675,0.751 false 2.634,1.822 3.061,1.967 0.427,0.145 10 CANL 2.604,1.9 2.519,1.9 2.519,1.9 2.399,1.453 false 2.76,1.57 3.187,1.715 0.427,0.145 10 CANH 2.73,1.648 2.645,1.648 2.645,1.648 2.48,1.453 false 2.795,0.985 3.127,1.131 0.333,0.145 10 GND 2.765,1.063 2.679,1.063 2.679,1.063 2.454,1.248 false 0.861,1.205 1.191,1.372 0.331,0.167 10 K34

Disconnect the suspension control ECU connector.

Text in Illustration
*a Rear view of wire harness connector
(to Suspension Control ECU)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
K34-7 (CANH) - K34-8 (CANL) L - B Cable disconnected from negative (-) battery terminal 54 to 69 Ω
K34-7 (CANH) - K34-1 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
K34-8 (CANL) - K34-1 (GND) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
K34-7 (CANH) - K34-3 (BAT2) L - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
K34-8 (CANL) - K34-3 (BAT2) B - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Memory)


U165546E01
4.756,1.509 4.611,1.509 4.611,1.509 4.459,1.086 false 0.056,0.043 0.233,0.196 0.177,0.154 10 *a 4.115,0.25 4.336,0.390 0.221,0.140 10 I41 4.577,1.086 4.841,1.301 4.841,1.301 4.95,1.301 false 4.967,1.227 5.435,1.364 0.468,0.137 10 CANN 4.787,1.447 5.255,1.585 0.468,0.137 10 CANP

Text in Illustration
*a Component without harness connected
(Outer Mirror Control ECU Assembly LH)
- -

a.
U165531E02
1.302,1.26 1.073,1.458 1.073,1.458 0.885,1.458 false 1.156,1.813 1.385,1.813 1.385,1.813 1.438,1.26 false 2.198,0.948 2.469,0.604 2.469,0.604 2.604,0.604 false 2.021,0.979 2.24,0.333 2.24,0.333 2.385,0.333 false 0.656,1.708 1.229,1.927 0.573,0.219 10 false CANP 0.365,1.375 0.969,1.594 0.604,0.219 10 false CANN 0.104,0.073 0.604,0.24 0.5,0.167 10 false *a 0.542,0.74 0.813,0.938 0.271,0.198 10 false I41 2.635,0.521 3.198,0.865 0.563,0.344 10 false GND 2.427,0.229 3.177,0.469 0.75,0.24 10 false CPUB

Disconnect the outer mirror control ECU assembly LH connector.

Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
I41-9 (CANP) - I41-8 (CANN) BE - L Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I41-9 (CANP) - I41-7 (GND) BE - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
I41-8 (CANN) - I41-7 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
I41-9 (CANP) - I41-6 (CPUB) BE - G Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I41-8 (CANN) - I41-6 (CPUB) L - G Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Memory)


U165547E01
4.756,1.509 4.611,1.509 4.611,1.509 4.459,1.086 false 0.056,0.043 0.233,0.196 0.177,0.154 10 *a 4.115,0.25 4.336,0.390 0.221,0.140 10 I38 4.577,1.086 4.841,1.301 4.841,1.301 4.95,1.301 false 4.967,1.227 5.435,1.364 0.468,0.137 10 CANN 4.787,1.447 5.255,1.585 0.468,0.137 10 CANP

Text in Illustration
*a Component without harness connected
(Outer Mirror Control ECU Assembly RH)
- -

a.
U165532E02
1.302,1.26 1.073,1.458 1.073,1.458 0.885,1.458 false 1.156,1.813 1.385,1.813 1.385,1.813 1.438,1.26 false 2.198,0.948 2.469,0.604 2.469,0.604 2.604,0.604 false 2.021,0.99 2.24,0.344 2.24,0.344 2.385,0.344 false 0.656,1.708 1.219,1.917 0.563,0.208 10 false CANP 0.365,1.375 0.948,1.573 0.583,0.198 10 false CANN 0.104,0.073 0.604,0.24 0.5,0.167 10 false *a 0.542,0.74 0.885,0.958 0.344,0.219 10 false I38 2.646,0.521 3.25,0.771 0.604,0.25 10 false GND 2.448,0.26 3.115,0.5 0.667,0.24 10 false CPUB

Disconnect the outer mirror control ECU assembly RH connector.

Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
I38-9 (CANP) - I38-8 (CANN) LG - L Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I38-9 (CANP) - I38-7 (GND) LG - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
I38-8 (CANN) - I38-7 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
I38-9 (CANP) - I38-6 (CPUB) LG - G Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I38-8 (CANN) - I38-6 (CPUB) L - G Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MULTIPLEX TILT AND TELESCOPIC ECU (w/ Power Tilt and Power Telescopic Steering Column System)


U165226E01
4.099,0.787 4.43,0.43 4.43,0.43 4.587,0.43 false 3.648,1.417 3.844,1.417 3.844,1.417 4.066,1.019 false 3.479,0.297 3.821,0.434 0.342,0.137 10 E144 0.108,0.037 0.382,0.174 0.274,0.137 10 *a 4.605,0.364 5.118,0.502 0.514,0.137 10 CANP 3.22,1.36 3.664,1.497 0.444,0.137 10 CANN

Text in Illustration
*a Component without harness connected
(Multiplex Tilt and Telescopic ECU)
- -

a.
U165224E01
2.117,1.085 2.391,1.669 2.391,1.669 2.539,1.669 false 2.491,0.958 2.715,0.706 2.715,0.706 2.864,0.706 false 2.342,0.949 2.599,1.355 2.599,1.355 2.748,1.355 false 2.082,0.913 2.384,0.395 2.384,0.395 2.548,0.395 false 0.069,0.062 0.343,0.263 0.274,0.201 10 *a 0.788,0.216 1.144,0.355 0.356,0.139 10 E144 2.602,0.319 3.022,0.458 0.420,0.139 10 CANP 2.582,1.591 3.002,1.729 0.420,0.139 10 CANN 2.881,0.633 3.301,0.772 0.420,0.139 10 GND 2.774,1.278 3.193,1.416 0.420,0.139 10 +B

Disconnect the multiplex tilt and telescopic ECU connector.

Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E144-3 (CANP) - E144-11 (CANN) P - L Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E144-3 (CANP) - E144-1 (GND) P - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E144-11 (CANN) - E144-1 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E144-3 (CANP) - E144-2 (+B) P - LA-W Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E144-11 (CANN) - E144-2 (+B) L - LA-W Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POWER SEAT SWITCH ASSEMBLY (w/ Memory)


U164153E01
4.141,0.312 4.385,0.450 0.243,0.138 10 c40 4.453,1.211 4.784,1.555 4.784,1.555 4.871,1.555 false 4.366,1.211 4.173,1.555 4.173,1.555 4.086,1.555 false 0.063,0.042 0.453,0.181 0.390,0.140 10 *a 3.66,1.495 4.078,1.635 0.417,0.140 10 MPX1 4.905,1.493 5.322,1.633 0.417,0.140 10 MPX2

Text in Illustration
*a Component without harness connected
(Power Seat Switch Assembly)
- -

a.
U165015E01
0.091,0.056 0.264,0.224 0.173,0.168 10 *a 0.636,1.787 0.859,1.955 0.222,0.168 10 +B 2.758,1.871 3.193,2.010 0.435,0.139 10 MPX1 2.837,1.627 3.272,1.766 0.435,0.139 10 MPX2 0.881,1.875 1.044,1.875 1.044,1.875 1.499,1.437 false 0.483,0.693 0.838,0.861 0.354,0.168 10 GND 0.905,0.781 1.056,0.781 1.056,0.781 1.494,1.212 false 2.798,0.843 3.042,0.984 0.244,0.142 10 c40 0.226,1.249 0.470,1.390 0.244,0.142 10 c39 2.464,1.609 2.588,1.937 2.588,1.937 2.73,1.937 false 2.813,1.699 2.742,1.699 2.742,1.699 2.562,1.608 false

Disconnect the power seat switch assembly connectors.

Text in Illustration
*a Rear view of wire harness connector
(to Power Seat Switch Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
c40-8 (MPX1) - c40-7 (MPX2) V - L Cable disconnected from negative (-) battery terminal 54 to 69 Ω
c40-8 (MPX1) - c39-1 (GND) V - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
c40-7 (MPX2) - c39-1 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
c40-8 (MPX1) - c39-6 (+B) V - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
c40-7 (MPX2) - c39-6 (+B) L - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU) (w/ Power Back Door System)


U163850E01
3.94,0.27 4.190,0.413 0.249,0.143 10 L52 0.053,0.048 0.302,0.191 0.249,0.143 10 *a 2.623,0.39 3.037,0.533 0.414,0.143 10 MPX1 2.722,0.2 3.136,0.343 0.414,0.143 10 MPX2 3.676,0.939 3.119,0.452 3.119,0.452 3.051,0.452 false 3.147,0.282 3.372,0.282 3.372,0.282 3.797,0.939 false

Text in Illustration
*a Component without harness connected
(Power Back Door Unit Assembly [Power Back Door ECU])
- -

a.
U165539E02
1.667,1.24 1.229,1.688 1.229,1.688 1.104,1.688 false 1.781,1.25 1.573,2 1.573,2 1.448,2 false 2.417,1.063 2.708,0.771 2.708,0.771 2.875,0.771 false 2.667,0.406 2.531,0.406 2.531,0.406 2.229,1.052 false 1.677,0.281 2.01,0.438 0.333,0.156 10 false L52 0.063,0.052 0.333,0.198 0.271,0.146 10 false *a 0.594,1.615 1.125,1.802 0.531,0.188 10 false MPX2 0.938,1.938 1.563,2.146 0.625,0.208 10 false MPX1 2.906,0.677 3.385,0.885 0.479,0.208 10 false GND 2.708,0.323 3.25,0.542 0.542,0.219 10 false ECUB

Disconnect the power back door unit assembly (power back door ECU) connector.

Text in Illustration
*a Front view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
L52-6 (MPX1) - L52-5 (MPX2) V - L Cable disconnected from negative (-) battery terminal 54 to 69 Ω
L52-6 (MPX1) - L52-11 (GND) V - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
L52-5 (MPX2) - L52-11 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
L52-6 (MPX1) - L52-10 (ECUB) V - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L52-5 (MPX2) - L52-10 (ECUB) L - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK NO. 2 MAIN BODY ECU (w/ Tail Gate Closer System)


U164150E01
3.104,0.372 3.362,0.533 0.258,0.161 10 L50 0.137,0.085 0.395,0.246 0.258,0.161 10 *a 1.465,0.33 1.921,0.491 0.456,0.161 10 MPX+ 2.453,1.312 1.83,0.689 1.83,0.689 1.62,0.689 false 1.914,0.419 2.184,0.419 2.184,0.419 2.612,1.307 false 1.206,0.607 1.661,0.767 0.456,0.161 10 MPX-

Text in Illustration
*a Component without harness connected
(No. 2 Main Body ECU)
- -

a.
U165540E01
1.665,0.277 1.915,0.418 0.250,0.141 10 L50 0.063,0.055 0.336,0.196 0.273,0.141 10 *a 0.347,1.589 0.768,1.730 0.421,0.141 10 BECU 1.17,1.404 0.985,1.67 0.985,1.67 0.861,1.67 false 0.583,0.495 1.004,0.636 0.421,0.141 10 GND 1.861,1.204 1.122,0.576 1.122,0.576 0.997,0.576 false 2.602,1.061 2.772,0.754 2.772,0.754 2.943,0.754 false 2.738,0.514 2.601,0.514 2.601,0.514 2.417,1.051 false 2.966,0.671 3.347,0.812 0.381,0.141 10 MPX- 2.763,0.431 3.184,0.572 0.421,0.141 10 MPX+

Disconnect the No. 2 main body ECU connector.

Text in Illustration
*a Front view of wire harness connector
(to No. 2 Main Body ECU)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
L50-11 (MPX+) - L50-12 (MPX-) LG - L Cable disconnected from negative (-) battery terminal 54 to 69 Ω
L50-11 (MPX+) - L50-7 (GND) LG - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
L50-12 (MPX-) - L50-7 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
L50-11 (MPX+) - L50-14 (BECU) LG - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L50-12 (MPX-) - L50-14 (BECU) L - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BUS BUFFER ECU (w/ Bus Buffer ECU)


a.
U165667E02
2.042,0.969 2.375,0.76 2.375,0.76 2.531,0.76 false 2.417,0.313 2.26,0.313 2.26,0.313 1.875,0.969 false 2.198,2.948 2.521,3.156 2.521,3.156 2.688,3.156 false 1.656,2.51 1.333,2.198 1.333,2.198 1.167,2.198 false 0.125,0.083 0.563,0.385 0.438,0.302 10 false *a 0.479,0.865 0.948,1.083 0.469,0.219 10 false E173 0.125,1.813 0.563,2.115 0.438,0.302 10 false *b 0.854,2.115 1.375,2.271 0.521,0.156 10 false CG 2.729,3.063 3.167,3.229 0.438,0.167 10 false BAT 2.583,0.688 3.156,0.896 0.573,0.208 10 false CAN- 2.469,0.229 3.073,0.479 0.604,0.25 10 false CAN+ 0.406,2.656 0.781,2.844 0.375,0.188 10 false E22

Disconnect the bus buffer ECU connector.

Text in Illustration
*a Front view of wire harness connector
(to Bus Buffer ECU)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E173-2 (CAN+) - E173-1 (CAN-) BE - GR Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E173-2 (CAN+) - E22-4 (CG) BE - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E173-1 (CAN-) - E22-4 (CG) GR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E173-2 (CAN+) - E22-16 (BAT) BE - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E173-1 (CAN-) - E22-16 (BAT) GR - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher