Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for LHD) › from 2015.08
RM2660E _57 Power Source / Network _052836 POWER DISTRIBUTION _0255530 MAIN BODY ECU(for LHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/o Door Control Battery)

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)


Hide 3.DISCHARGE DOOR CONTROL BATTERY AND DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Door Control Battery)

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Make sure to perform this procedure with the power supply of the battery and door control battery cut to prevent damage during removal and installation of the instrument panel junction block assembly.

·

Make sure to perform the following procedures, and then perform removal and installation of the instrument panel junction block assembly with the power supply from the battery and door control battery cut.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

When the ignition switch is turned off after the door control battery is fully charged, the door control battery becomes completely discharged due to self-discharge within approximately 30 minutes.

·

Approximately 90 seconds after the ignition switch is turned on (IG), the door control battery becomes fully charged.

·

When approximately 30 minutes or more elapse after the ignition switch is turned off, the Active Test may not be able to be performed.



a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.

NOTICE:

Do not perform the Active Test at this time.



e.

Disconnect the cable from the negative (-) battery terminal.


f.

Repeat the "Shock Detection Unlock" Active Test until the multiplex network body ECU (main body ECU) communication lost error "Lost communication with vehicle" appears on the GTS display.

NOTICE:
·

When the door control battery becomes completely discharged and the power supply is cut, the multiplex network body ECU (main body ECU) communication lost error "Lost communication with vehicle" appears on the GTS display.

·

The number of times the Active Test can be performed depends on the charge condition of the door control battery.




Hide 55449C 6.REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

Hide 55403C 7.REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

Hide 55474C 8.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55475A 9.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55606 10.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Cover)

Hide 55432D 12.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 55303B 13.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 73900 14.REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 82733A 15.REMOVE COWL SIDE JUNCTION BLOCK LH

a.
E333957E02
3.004,2.822 3.261,3.026 0.257,0.205 12 *A

Disconnect each connector.

Text in Illustration
*A w/ VGRS
V100135

Connector
V100137

Connector with Lock Lever
V100155

Protective Tape


b.

Disconnect the connector with lock lever.

HINT:

Use the same procedure to disconnect the connector with lock lever on the other side.


i.

Using a screwdriver, insert the lock lever to detach the claw.

HINT:

Tape the screwdriver tip before use.



ii.

Tilt the lock lever and disconnect the connector.



c.
E333958

Remove the bolt and 2 nuts and cowl side junction block LH.


d.
E333959

Disconnect the connector with lock lever.

i.

Using a screwdriver, insert the lock lever to detach the claw.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
V100155

Protective Tape


ii.

Tilt the lock lever and disconnect the connector.



e.
E333960

Detach the claw and slide the connector lock.


f.
E333961

Disconnect the connector with lock lever.

i.

Using a screwdriver, insert the lock lever to detach the claw.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
V100155

Protective Tape


ii.

Tilt the lock lever and disconnect the connector.



Hide 82673A 17.REMOVE JUNCTION BLOCK BRACKET

a.
E333962

Remove the bolt.


b.

Detach the guide and remove the junction block bracket.


Hide 89221 18.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, replace it with a new one.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to service bulletin.



a.
E333963E03
0.458,2.646 0.458,3.063 true 0.573,2.573 1.25,2.573 true 1.281,2.479 1.469,2.656 0.188,0.177 10 false *a 0.385,3.083 0.573,3.26 0.188,0.177 10 false *b

Press the claw of the cowl side junction block LH as shown in the illustration to release the lock.

Text in Illustration
*a Claw of Cowl Side Junction Block LH
*b Main Body ECU (Multiplex Network Body ECU)


b.
E333964

With the cowl side junction block LH lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the main body ECU (multiplex network body ECU) and cowl side junction block LH.

Text in Illustration
V100155

Protective Tape

NOTICE:

Use a screwdriver with a diameter of between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).



c.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disengaged.

NOTICE:

Do not insert the screwdriver between the cowl side junction block LH and the connector of the main body ECU (multiplex network body ECU).

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).



d.
E333965

Raise the main body ECU (multiplex network body ECU) as shown by the black arrow, and then slide it out as shown by the white arrow in the illustration.

Text in Illustration
V100135

Raise
V100136

Slide Out

NOTICE:

Do not touch the main body ECU (multiplex network body ECU) connector.