Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either Condition is met:
·

Communication stop for "Spiral cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Steering sensor CAN branch wire or connector

·

Power source circuit of steering sensor

·

Steering sensor ground circuit

·

Steering sensor



WIRING DIAGRAM

C344583E12
0.396,1.979 0.958,2.188 0.563,0.208 10 false E133 5.667,1.031 6.354,1.281 0.688,0.25 10 false CANH 1.698,0.927 2.26,1.094 0.563,0.167 10 false 10 1.698,1.458 2.26,1.625 0.563,0.167 10 false 20 0.396,2.146 2.823,2.646 2.427,0.5 10 false No. 2 CAN Junction Connector 5.677,1.552 6.323,1.771 0.646,0.219 10 false CANL 5.667,2.729 6.25,2.979 0.583,0.25 10 false BAT 5.667,3.396 6.26,3.646 0.594,0.25 10 false IG 5.667,3.927 6.271,4.135 0.604,0.208 10 false ESS 4.208,0.802 4.563,0.99 0.354,0.188 10 false 4*1 4.208,2.521 4.542,2.729 0.333,0.208 10 false 6*1 4.208,3.167 4.521,3.385 0.313,0.219 10 false 5*1 4.208,3.74 4.448,3.885 0.24,0.146 10 false 2*1 4.208,1.333 4.521,1.531 0.313,0.198 10 false 3*1 4.698,0.802 5.115,1.01 0.417,0.208 10 false 3*2 4.688,2.521 5.042,2.719 0.354,0.198 10 false 5*2 4.698,3.167 5.021,3.385 0.323,0.219 10 false 4*2 4.698,3.719 4.958,3.865 0.26,0.146 10 false 1*2 4.656,1.021 5.073,1.271 0.417,0.25 10 false E121 4.656,2.729 5.063,2.948 0.406,0.219 10 false E121 4.656,3.365 5.104,3.604 0.448,0.24 10 false E121 4.656,3.938 5.083,4.125 0.427,0.188 10 false E121 4.656,1.552 5.073,1.771 0.417,0.219 10 false E121 4.146,1.021 4.573,1.229 0.427,0.208 10 false E181 4.146,2.74 4.552,2.948 0.406,0.208 10 false E181 4.135,3.365 4.542,3.563 0.406,0.198 10 false E181 4.146,3.938 4.625,4.177 0.479,0.24 10 false E181 4.146,1.552 4.594,1.74 0.448,0.188 10 false E181 4.698,1.333 5.073,1.563 0.375,0.229 10 false 2*2 5.167,1.021 5.604,1.229 0.438,0.208 10 false E163 5.219,0.802 5.594,1.021 0.375,0.219 10 false 3*3 5.167,2.74 5.604,2.938 0.438,0.198 10 false E163 5.219,2.531 5.583,2.719 0.365,0.188 10 false 5*3 5.167,3.365 5.625,3.573 0.458,0.208 10 false E163 5.219,3.156 5.563,3.344 0.344,0.188 10 false 4*3 5.167,3.948 5.594,4.146 0.427,0.198 10 false E163 5.219,3.729 5.479,3.875 0.26,0.146 10 false 1*3 5.167,1.552 5.573,1.74 0.406,0.188 10 false E163 5.219,1.333 5.531,1.563 0.313,0.229 10 false 2*3 5.573,4.781 6.927,5.156 1.354,0.375 10 false Steering Sensor 0.208,2.74 2.094,3.188 1.885,0.448 10 false from J/B-B NO.1 Fuse*1, *2, Steering Control ECU*3 0.625,3.354 2.156,3.719 1.531,0.365 10 false from IG1 NO.3 Relay 2.865,3.229 4.073,3.448 1.208,0.219 10 false ECU-IG NO.1 0.271,3.896 3.167,4.552 2.896,0.656 10 false *1: w/o Variable Gear Ratio Steering System, w/o Entry and Start System 0.271,4.573 3.104,5.188 2.833,0.615 10 false *2: w/o Variable Gear Ratio Steering System, w/ Entry and Start System 0.271,5.25 3.313,5.719 3.042,0.469 10 false *3: w/ Variable Gear Ratio Steering System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Drive the vehicle for 6.04 seconds or more at a speed of 36 km/h (22 mph) or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.

U165707E01
3.51,0.572 3.856,0.714 0.347,0.142 10 E121 4.007,0.572 4.509,0.714 0.502,0.142 10 *B 1.363,0.572 1.710,0.714 0.347,0.142 10 E181 1.86,0.572 2.362,0.714 0.502,0.142 10 *A 5.564,0.572 5.911,0.714 0.347,0.142 10 E163 6.061,0.572 6.269,0.714 0.208,0.142 10 *C 0.085,0.104 0.432,0.246 0.347,0.142 10 *a 0.3,1.179 1.122,1.491 0.821,0.312 10 CANL 1.455,1.55 0.879,1.245 0.879,1.245 0.743,1.245 false 0.883,0.927 1.005,0.927 1.005,0.927 1.612,1.55 false 0.471,0.858 0.903,1.170 0.433,0.312 10 CANH 2.357,1.184 3.178,1.496 0.821,0.312 10 CANL 3.511,1.555 2.935,1.249 2.935,1.249 2.8,1.249 false 2.94,0.932 3.061,0.932 3.061,0.932 3.668,1.555 false 2.527,0.862 2.960,1.174 0.433,0.312 10 CANH 4.459,1.142 5.280,1.454 0.821,0.312 10 CANL 5.613,1.513 5.037,1.207 5.037,1.207 4.901,1.207 false 5.041,0.89 5.163,0.89 5.163,0.89 5.77,1.513 false 4.629,0.82 5.061,1.132 0.433,0.312 10 CANH

Text in Illustration
*A w/o Variable Gear Ratio Steering System, w/o Entry and Start System *B w/o Variable Gear Ratio Steering System, w/ Entry and Start System
*C w/ Variable Gear Ratio Steering System - -
*a Front view of wire harness connector
(to Steering Sensor)
- -


b.

Disconnect the steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Variable Gear Ratio Steering System, w/o Entry and Start System:
Tester Connection Condition Specified Condition
E181-4 (CANH) - E181-3 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

w/o Variable Gear Ratio Steering System, w/ Entry and Start System:
Tester Connection Condition Specified Condition
E121-3 (CANH) - E121-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

w/ Variable Gear Ratio Steering System:
Tester Connection Condition Specified Condition
E163-3 (CANH) - E163-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

C344582E02
1.302,0.417 1.802,0.667 0.5,0.25 3.417,0.417 3.917,0.667 0.5,0.25 5.5,0.417 6,0.667 0.5,0.25 0.917,2 1.083,2 1.083,2 1.26,1.688 false 1.948,1.667 2.031,2 2.031,2 2.135,2 false 3.083,2 3.24,2 3.24,2 3.333,1.677 false 4,1.667 4.146,2 4.146,2 4.25,2 false 6.073,1.625 6.281,1.792 6.281,1.792 6.385,1.792 false 5.083,1.792 5.219,1.792 5.219,1.792 5.417,1.625 false 1.781,1.542 2.177,1.24 2.177,1.24 2.281,1.24 false 3.813,1.552 4.208,1.25 4.208,1.25 4.313,1.25 false 5.896,1.521 6.292,1.219 6.292,1.219 6.396,1.219 false 2.313,1.167 2.719,1.365 0.406,0.198 10 false IG 0.49,1.927 1.104,2.125 0.615,0.198 10 false ESS 2.167,1.927 2.667,2.167 0.5,0.24 10 false BAT 1.396,0.458 1.802,0.656 0.406,0.198 10 false E181 1.854,0.458 2.177,0.667 0.323,0.208 10 false *A 2.688,1.927 3.302,2.125 0.615,0.198 10 false ESS 4.302,1.917 4.802,2.156 0.5,0.24 10 false BAT 6.438,1.708 6.938,1.948 0.5,0.24 10 false BAT 4.698,1.708 5.313,1.906 0.615,0.198 10 false ESS 3.51,0.469 3.917,0.667 0.406,0.198 10 false E121 5.594,0.469 6,0.667 0.406,0.198 10 false E163 3.969,0.458 4.292,0.667 0.323,0.208 10 false *B 6.052,0.458 6.375,0.667 0.323,0.208 10 false *C 4.333,1.177 4.74,1.375 0.406,0.198 10 false IG 6.427,1.135 6.833,1.333 0.406,0.198 10 false IG 0.156,0.083 0.479,0.292 0.323,0.208 10 false *a

Text in Illustration
*A w/o Variable Gear Ratio Steering System, w/o Entry and Start System *B w/o Variable Gear Ratio Steering System, w/ Entry and Start System
*C w/ Variable Gear Ratio Steering System - -
*a Front view of wire harness connector
(to Steering Sensor)
- -

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Variable Gear Ratio Steering System, w/o Entry and Start System:
Tester Connection Condition Specified Condition
E181-6 (BAT) - Body ground Always 11 to 14 V
E181-5 (IG) - Body ground Ignition switch ON 11 to 14 V

w/o Variable Gear Ratio Steering System, w/ Entry and Start System:
Tester Connection Condition Specified Condition
E121-5 (BAT) - Body ground Always 11 to 14 V
E121-4 (IG) - Body ground Ignition switch ON 11 to 14 V

w/ Variable Gear Ratio Steering System:
Tester Connection Condition Specified Condition
E163-5 (BAT) - Body ground Always 11 to 14 V
E163-4 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Variable Gear Ratio Steering System, w/o Entry and Start System:
Tester Connection Condition Specified Condition
E181-2 (ESS) - Body ground Always Below 1 Ω

w/o Variable Gear Ratio Steering System, w/ Entry and Start System:
Tester Connection Condition Specified Condition
E121-1 (ESS) - Body ground Always Below 1 Ω

w/ Variable Gear Ratio Steering System:
Tester Connection Condition Specified Condition
E163-1 (ESS) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR