Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0235 There is no communication from the millimeter wave radar sensor assembly.
·

Millimeter wave radar sensor assembly CAN main wire or connector

·

Power source or inside of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit

·

Millimeter wave radar sensor assembly



WIRING DIAGRAM

C251175E10
5.198,3.917 7.125,4.583 1.927,0.667 10 false Millimeter Wave Radar Sensor Assembly 5.198,3.74 5.594,3.906 0.396,0.167 10 false A72 5.396,3.042 5.531,3.229 0.135,0.188 10 false 1 5.615,3.146 6.104,3.365 0.49,0.219 10 false SGND 5.615,1.281 6.104,1.469 0.49,0.188 10 false CA1N 1.656,1.073 1.927,1.24 0.271,0.167 10 false 15 1.656,0.479 1.813,0.625 0.156,0.146 10 false 5 5.385,1.083 5.594,1.385 0.208,0.302 10 false 6 5.396,0.479 5.594,0.875 0.198,0.396 10 false 5 5.615,0.479 6.094,0.698 0.479,0.219 10 false CA1P 5.385,2.448 5.49,2.625 0.104,0.177 10 false 8 3.99,2.396 5.094,2.719 1.104,0.323 10 false ECU-IG NO.2 5.615,2.552 6.115,2.802 0.5,0.25 10 false IGB 1.979,2.531 3.698,2.75 1.719,0.219 10 false from IG1 NO.1 Relay 0.344,1.677 2.719,2.115 2.375,0.438 10 false No. 10 CAN Junction Connector 0.344,1.521 0.792,1.719 0.448,0.198 10 false E174

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Drive the vehicle for 2.6 seconds or more at a speed of 36 km/h (22 mph) or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Gateway of the driving support ECU assembly, this indicates a local bus malfunction. Troubleshoot for DTC U1002 and check for malfunctions in local bus.


Result
Result Proceed to
DTC U1002 is not output from driving support ECU assembly. A
DTC U1002 is output from driving support ECU assembly. B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN MAIN WIRE)

B

2.CHECK FOR OPEN IN CAN BUS WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN MAIN WIRE)
a.
U165610E01
0.061,0.054 0.353,0.341 0.292,0.288 10 *a 0.717,1.788 1.185,1.939 0.468,0.151 10 CA1N 0.27,1.482 0.738,1.633 0.468,0.151 10 CA1P 1.593,0.161 1.860,0.301 0.267,0.140 10 A72 1.462,1.191 0.937,1.546 0.937,1.546 0.751,1.546 false 1.255,1.858 1.427,1.858 1.427,1.858 1.632,1.22 false

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A72-5 (CA1P) - A72-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MILLIMETER WAVE RADAR SENSOR ASSEMBLY (CA1P, CA1N)

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165611E01
0.061,0.054 0.353,0.341 0.292,0.288 10 *a 0.308,0.589 0.777,0.741 0.468,0.151 10 SGND 2.667,1.606 2.938,1.758 0.270,0.151 10 IGB 1.593,0.161 1.860,0.301 0.267,0.140 10 A72 1.462,1.003 1.01,0.678 1.01,0.678 0.824,0.678 false 2.639,1.691 2.405,1.691 2.405,1.691 2.021,1.22 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A72-8 (IGB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A72-1 (SGND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR