| Detection Item | Symptom | Trouble Area |
|---|---|---|
| Main Body ECU Communication Stop Mode | Either Condition is met:
·
|
·
Main body ECU (multiplex network body ECU) CAN branch wire or connector ·
Power source circuit of main body ECU (multiplex network body ECU) ·
Power source circuit of cowl side junction block LH ·
Main body ECU (multiplex network body ECU) ground circuit ·
Cowl side junction block LH ground circuit ·
Main body ECU (multiplex network body ECU) ·
Cowl side junction block LH |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and turn the blind spot monitor main switch to ON, and then wait 13.6 seconds or more.
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E118-14 (CANH) - E118-13 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| *a | Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
OK
NG
Connect the cable to the negative (-) battery terminal.
When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL).
Reconnect the cowl side junction block LH connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-31 (BECU) - Body ground | Always | 11 to 14 V |
| A-30 (ACC) - Body ground | Ignition switch ACC | 11 to 14 V |
| A-32 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-11 (GND1) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
OK
NG
Disconnect the cowl side junction block LH connectors.
| *a | Front view of wire harness connector
(to Cowl Side Junction Block LH) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2H-19 - Body ground | Always | 11 to 14 V |
| 2G-1 - Body ground | Always | 11 to 14 V |
| 2J-18 - Body ground | Ignition switch ACC | 11 to 14 V |
| 2I-18 - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2J-1 - Body ground | Always | Below 1 Ω |
OK
NG