Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  AFS ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
AFS ECU Communication Stop Mode Either Condition is met:
·

Communication stop for "Headlight swivel (AFS)" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "AFS ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Headlight swivel ECU assembly CAN branch wire or connector

·

Power source circuit of headlight swivel ECU assembly

·

Headlight swivel ECU assembly ground circuit

·

Headlight swivel ECU assembly



WIRING DIAGRAM

C358555E03
0.219,2.302 2.406,2.604 2.188,0.302 10 false No. 2 CAN Junction Connector 0.219,2.135 0.75,2.333 0.531,0.198 10 false E133 2.073,2.677 3.469,2.99 1.396,0.313 10 false from IG1 Relay 1.75,3.5 3.208,3.854 1.458,0.354 10 false from IG NO. 4 Relay 3.948,2.521 5.25,2.833 1.302,0.313 10 false ENG-IG NO. 1 3.927,3.333 5.24,3.615 1.313,0.281 10 false ECU-IG NO. 5 4.885,5.156 7.115,5.615 2.229,0.458 10 false Headlight Leveling ECU Assembly 4.885,5.01 5.865,5.208 0.979,0.198 10 false E101 5.656,1.219 6.188,1.417 0.531,0.198 10 false CANH 5.667,1.781 6.198,1.979 0.531,0.198 10 false CANL 5.656,2.688 6.188,2.885 0.531,0.198 10 false IG 5.656,3.531 6.188,3.729 0.531,0.198 10 false IGS 5.667,4.344 6.198,4.542 0.531,0.198 10 false E1 1.75,1.083 2.281,1.281 0.531,0.198 10 false 4 1.74,1.667 2.271,1.865 0.531,0.198 10 false 14 5.365,1.083 5.896,1.281 0.531,0.198 10 false 12 5.365,1.698 5.896,1.896 0.531,0.198 10 false 13 5.385,2.583 5.917,2.781 0.531,0.198 10 false 15 5.375,3.396 5.906,3.594 0.531,0.198 10 false 14 5.396,4.219 5.969,4.406 0.573,0.188 10 false 22 0.229,0.156 3.49,0.458 3.26,0.302 12 false w/ Automatic High Beam System:

C329407E26
5.292,4.531 5.792,4.719 0.5,0.188 10 false E109 5.604,3.74 5.958,3.979 0.354,0.24 10 false E1 5.344,3.594 5.563,3.792 0.219,0.198 10 false 9 5.625,2.75 5.979,2.99 0.354,0.24 10 false IG 5.354,2.646 5.542,2.844 0.188,0.198 10 false 1 5.604,1.615 6.313,1.854 0.708,0.24 10 false CANL 5.354,1.469 5.563,1.667 0.208,0.198 10 false 7 5.354,0.906 5.604,1.094 0.25,0.188 10 false 6 1.646,1.49 1.896,1.729 0.25,0.24 10 false 14 5.615,1.031 6.323,1.271 0.708,0.24 10 false CANH 1.667,0.896 2.021,1.135 0.354,0.24 10 false 4 5.292,4.698 6.563,5.469 1.271,0.771 10 false Headlight Leveling ECU Assembly 0.25,1.958 0.781,2.156 0.531,0.198 10 false E133 0.25,2.115 2.438,2.385 2.188,0.271 10 false No. 2 CAN Junction Connector 1.938,2.76 3.094,3.073 1.156,0.313 10 false from IG1 Relay 3.833,2.594 4.865,2.792 1.031,0.198 10 false ENG-IG NO.1 0.188,0.135 4.052,0.49 3.865,0.354 12 false w/o Automatic High Beam System:

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (HEADLIGHT LEVELING ECU ASSEMBLY CAN BRANCH WIRE)
a.
U165448E01
2.916,0.423 3.307,0.561 0.391,0.137 10 CANL 2.719,0.16 3.138,0.298 0.420,0.137 10 CANH 0.08,0.067 0.565,0.204 0.485,0.137 10 *a 1.536,1.716 1.882,1.854 0.346,0.137 10 E109 2.172,1.716 2.518,1.854 0.346,0.137 10 *B 1.536,0.238 1.882,0.375 0.346,0.137 10 E101 2.172,0.238 2.518,0.375 0.346,0.137 10 *A 2.882,1.955 3.273,2.092 0.391,0.137 10 CANL 2.684,1.692 3.104,1.829 0.420,0.137 10 CANH 2.796,0.913 2.839,0.507 2.839,0.507 2.908,0.507 false 2.697,0.249 2.577,0.249 2.577,0.249 2.675,0.9 false 2.392,2.415 2.804,2.039 2.804,2.039 2.873,2.039 false 2.663,1.781 2.542,1.781 2.542,1.781 2.271,2.402 false

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Automatic High Beam System:
Tester Connection Condition Specified Condition
E101-12 (CANH) - E101-13 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

w/o Automatic High Beam System:
Tester Connection Condition Specified Condition
E109-6 (CANH) - E109-7 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*A w/ Automatic High Beam System
*B w/o Automatic High Beam System
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT LEVELING ECU ASSEMBLY (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165449E01
0.082,0.067 0.566,0.204 0.485,0.137 10 *a 1.538,1.751 1.883,1.888 0.346,0.137 10 E109 2.174,1.751 2.346,1.888 0.172,0.137 10 *B 1.538,0.238 1.883,0.375 0.346,0.137 10 E101 2.174,0.238 2.519,0.375 0.346,0.137 10 *A 2.986,2.118 3.201,2.256 0.215,0.137 10 E1 2.686,2.415 2.909,2.202 2.909,2.202 2.978,2.202 false 2.219,1.492 2.434,1.630 0.215,0.137 10 E1 1.6,1.176 2.088,1.574 2.088,1.574 2.2,1.574 false 0.148,2.104 0.362,2.241 0.215,0.137 10 IG 0.743,2.411 0.446,2.186 0.446,2.186 0.378,2.186 false 1.144,1.502 1.359,1.640 0.215,0.137 10 IG 0.755,1.168 1.013,1.584 1.013,1.584 1.126,1.584 false 0.864,1.722 1.134,1.859 0.270,0.137 10 IGS 0.636,1.168 0.733,1.803 0.733,1.803 0.845,1.803 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Automatic High Beam System:
Tester Connection Switch Condition Specified Condition
E101-15 (IG) - Body ground Ignition switch ON 11 to 14 V
E101-14 (IGS) - Body ground Ignition switch ON 11 to 14 V

w/o Automatic High Beam System:
Tester Connection Switch Condition Specified Condition
E109-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Automatic High Beam System:
Tester Connection Condition Specified Condition
E101-22 (E1) - Body ground Always Below 1 Ω

w/o Automatic High Beam System:
Tester Connection Condition Specified Condition
E109-9 (E1) - Body ground Always Below 1 Ω



Text in Illustration
*A w/ Automatic High Beam System
*B w/o Automatic High Beam System
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)


OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR