Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Blind Spot Monitor Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Blind Spot Monitor Sensor Communication Stop Mode Either Condition is met:
·

Communication stop for "Blind Spot Monitor Master" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Blind Spot Monitor Sensor Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Blind spot monitor sensor LH CAN branch wire or connector

·

Power source circuit of blind spot monitor sensor LH

·

Blind spot monitor sensor LH ground circuit

·

Blind spot monitor sensor LH



WIRING DIAGRAM

C358557E02
0.417,1.896 2.583,2.271 2.167,0.375 10 false No. 4 CAN Junction Connector 0.417,1.75 1.292,1.958 0.875,0.208 10 false K58 1.771,2.406 3.281,2.771 1.51,0.365 10 false from IG1 NO.2 Relay 3.938,2.229 5.063,2.49 1.125,0.26 10 false ECU-IG NO.3 5.146,4.146 7.104,4.656 1.958,0.51 10 false Blind Spot Monitor Sensor LH 5.156,3.979 6.021,4.167 0.865,0.188 10 false r2 5.719,0.802 6.323,1 0.604,0.198 10 false CA1P 5.479,0.698 5.792,0.896 0.313,0.198 10 false 2 5.719,1.396 6.281,1.604 0.563,0.208 10 false CA1N 5.708,2.417 6.292,2.615 0.583,0.198 10 false BRB 5.708,3.031 6.406,3.229 0.698,0.198 10 false BRGD 5.469,1.281 5.781,1.479 0.313,0.198 10 false 7 5.406,2.885 5.719,3.083 0.313,0.198 10 false 10 5.469,2.292 5.781,2.49 0.313,0.198 10 false 5 1.781,0.698 2.094,0.896 0.313,0.198 10 false 1 1.792,1.281 2.104,1.479 0.313,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 13 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH CAN BRANCH WIRE)
a.
U165544E01
0.107,0.093 0.282,0.268 0.175,0.175 10 *a 1.655,0.283 1.798,0.428 0.144,0.145 10 r2 0.378,0.704 0.762,0.849 0.383,0.145 10 CA1P 0.361,1.598 0.755,1.743 0.394,0.145 10 CA1N 1.522,1.335 1.057,1.687 1.057,1.687 0.842,1.687 false 1.522,1.141 1.057,0.789 1.057,0.789 0.842,0.789 false

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r2-2 (CA1P) - r2-7 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)



OK

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BLIND SPOT MONITOR SENSOR LH (CA1P, CA1N)

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY AND BODY GROUND)
a.
U165545E01
0.107,0.093 0.282,0.268 0.175,0.175 10 *a 1.655,0.283 1.798,0.428 0.144,0.145 10 r2 2.742,0.704 3.125,0.849 0.383,0.145 10 BRB 2.724,1.598 3.215,1.743 0.491,0.145 10 BRGD 2.029,1.335 2.494,1.687 2.494,1.687 2.709,1.687 false 2.029,1.141 2.494,0.789 2.494,0.789 2.709,0.789 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
r2-5 (BRB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r2-10 (BRGD) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR