| Detection Item | Symptom | Trouble Area |
|---|---|---|
| Tire Pressure Monitor ECU Communication Stop Mode | Either Condition is met:
·
|
·
Tire pressure warning ECU CAN branch wire or connector ·
Power source circuit of tire pressure warning ECU ·
Tire pressure warning ECU ground circuit ·
Tire pressure warning ECU |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds.
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the tire pressure warning ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L65-9 (CANH) - L65-10 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L75-9 (CANH) - L75-10 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| *A | w/o Front Antenna |
| *B | w/ Front Antenna |
| *a | Front view of wire harness connector
(to Tire Pressure Warning ECU) |
OK
NG
Connect the cable to the negative (-) battery terminal.
When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L65-7 (+B) - Body ground | Always | 11 to 14 V |
| L65-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L75-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L65-12 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L75-12 (GND) - Body ground | Always | Below 1 Ω |
| *A | w/o Front Antenna |
| *B | w/ Front Antenna |
| *a | Front view of wire harness connector
(to Tire Pressure Warning ECU) |
OK
NG