Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › 2015.08–2016.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Check Bus 3 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus wires and GND when no resistance exists between terminal 6 (CA3H) of the central gateway ECU and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU and terminal 4 (CG) of the DLC3.

Detection Item Trouble Area
No resistance exists between terminal 6 (CA3H) of the central gateway ECU and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU and terminal 4 (CG) of the DLC3.
·

Short to GND in bus 3 CAN main wires

·

Short to GND in bus 3 CAN branch wires

·

Central gateway ECU

·

Multi-media module receiver assembly*1

·

Bus buffer ECU*2

·

Radio and display receiver assembly*3

·

No. 5 CAN junction connector

·

No. 6 CAN junction connector

·

No. 2 CAN junction terminal



*1: for Multi-media Module Receiver Type

*2: w/ Bus Buffer ECU

*3: for Radio and Display Type


WIRING DIAGRAM

C344611E02
5.679,1.773 7.080,2.091 1.401,0.318 10 E145 5.982,1.479 6.472,1.668 0.489,0.188 10 CA3L 5.982,0.732 6.472,0.920 0.489,0.188 10 CA3H 5.782,0.732 6.271,0.920 0.489,0.188 10 6 5.726,1.278 6.215,1.467 0.489,0.188 10 21 4.124,0.732 4.613,0.920 0.489,0.188 10 8 4.124,1.278 4.613,1.467 0.489,0.188 10 19 1.368,0.732 1.858,0.920 0.489,0.188 10 2 1.368,1.278 1.858,1.467 0.489,0.188 10 1 0.85,0.83 1.339,1.018 0.489,0.188 10 CAN+ 0.85,1.376 1.339,1.565 0.489,0.188 10 CAN- 3.176,0.732 3.665,0.920 0.489,0.188 10 9 3.106,1.278 3.595,1.467 0.489,0.188 10 20 4.124,2.764 4.613,2.952 0.489,0.188 10 11 4.124,3.31 4.613,3.498 0.489,0.188 10 22 1.368,2.764 1.858,2.952 0.489,0.188 10 1 1.368,3.31 1.858,3.498 0.489,0.188 10 2 0.85,2.862 1.339,3.050 0.489,0.188 10 CANH 0.85,3.408 1.339,3.596 0.489,0.188 10 CANL 3.106,2.764 3.595,2.952 0.489,0.188 10 10 3.106,3.31 3.595,3.498 0.489,0.188 10 21 4.124,4.888 4.613,5.077 0.489,0.188 10 6 4.124,5.435 4.613,5.623 0.489,0.188 10 17 4.124,6.897 4.613,7.085 0.489,0.188 10 7 4.124,7.443 4.613,7.631 0.489,0.188 10 18 1.368,4.888 1.858,5.077 0.489,0.188 10 9 1.368,5.435 1.858,5.623 0.489,0.188 10 10 0.85,4.987 1.339,5.175 0.489,0.188 10 CANH 0.85,5.533 1.339,5.721 0.489,0.188 10 CANL 5.679,1.914 7.080,2.231 1.401,0.318 10 Central Gateway ECU 5.193,7.924 7.025,8.242 1.832,0.318 10 F98 5.982,7.644 6.472,7.832 0.489,0.188 10 CANL 5.982,6.897 6.472,7.085 0.489,0.188 10 CANH 5.782,6.897 6.271,7.085 0.489,0.188 10 3 5.782,7.443 6.271,7.631 0.489,0.188 10 2 5.193,8.064 7.025,8.382 1.832,0.318 10 No. 2 CAN Junction Terminal 0.327,1.787 2.446,2.263 2.119,0.475 10 E173 0.327,1.937 2.446,2.412 2.119,0.475 10 Bus Buffer ECU*1 0.154,3.805 2.273,4.280 2.119,0.475 10 F77 0.154,3.954 2.273,4.430 2.119,0.475 10 Multi-media Module Receiver Assembly*2 0.327,5.907 2.446,6.382 2.119,0.475 10 F124 0.327,6.056 2.446,6.531 2.119,0.475 10 Radio and Display Receiver Assembly*3 3.026,3.805 4.997,4.021 1.971,0.216 10 E152 3.026,3.95 4.997,4.166 1.971,0.216 10 No. 5 CAN Junction Connector 3.026,7.924 4.895,8.140 1.869,0.216 10 F99 3.026,8.069 4.978,8.285 1.952,0.216 10 No. 6 CAN Junction Connector 0.252,7.775 2.431,7.940 2.179,0.165 10 *1: w/ Bus Buffer ECU 0.252,8.108 2.825,8.274 2.573,0.165 10 *2: for Multi-media Module Receiver Type 0.252,8.442 2.431,8.608 2.179,0.165 10 *3: for Radio and Display Type

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 5 CAN JUNCTION CONNECTOR)
a.
U165647E02
1.625,3.125 1.271,2.688 1.271,2.688 1.156,2.688 false 2.281,1.229 2.646,0.667 2.646,0.667 2.76,0.667 false 2.198,1.51 2.552,2.115 2.552,2.115 2.688,2.115 false 0.073,0.063 0.427,0.281 0.354,0.219 10 false *a 0.073,2.406 0.396,2.583 0.323,0.177 10 false *b 1.51,0.406 2,0.635 0.49,0.229 10 false E145 0.24,3.427 0.625,3.625 0.385,0.198 10 false E22 0.865,2.615 1.26,2.823 0.396,0.208 10 false CG 2.74,2.031 3.271,2.198 0.531,0.167 10 false CA3L 2.813,0.573 3.333,0.771 0.521,0.198 10 false CA3H

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the central gateway ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-6 (CA3H) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-21 (CA3L) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU)
*b Front view of DLC3



OK

NG

2.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the E145 central gateway ECU connector.



NEXT

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION TERMINAL - NO. 6 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION TERMINAL - NO. 6 CAN JUNCTION CONNECTOR)
a.
U165523E02
1.396,0.813 1.198,0.521 1.198,0.521 1.083,0.521 false 1.302,0.25 1.573,0.25 1.573,0.25 1.688,0.813 false 1.667,2.417 1.313,1.979 1.313,1.979 1.198,1.979 false 0.063,0.052 0.292,0.323 0.229,0.271 10 false *a 0.063,1.635 0.292,1.906 0.229,0.271 10 false *b 0.448,0.938 0.844,1.167 0.396,0.229 10 false F98 0.625,0.458 1.167,0.667 0.542,0.208 10 false CANH 0.885,0.177 1.469,0.385 0.583,0.208 10 false CANL 0.417,2.573 0.823,2.833 0.406,0.26 10 false E22 0.906,1.896 1.292,2.094 0.385,0.198 10 false CG

Disconnect the No. 2 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F98-3 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F98-2 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 CAN Junction Terminal)
*b Front view of DLC3



OK

REPLACE NO. 2 CAN JUNCTION TERMINAL

NG

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the F98 No. 2 CAN junction terminal connector.



NEXT

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 5 CAN junction connector.

U165518E01
0.051,0.046 0.346,0.271 0.295,0.225 10 *a 4.217,0.046 4.512,0.271 0.295,0.225 10 *b 0.795,0.024 1.479,0.175 0.684,0.151 10 CANH*c 2.21,1.405 2.894,1.551 0.684,0.146 10 CANL*c 0.67,0.598 1.354,0.749 0.684,0.151 10 CANH*f 0.753,0.184 1.437,0.336 0.684,0.151 10 CANH*d 0.606,0.393 1.290,0.545 0.684,0.151 10 CANH*e 0.671,1.129 1.355,1.276 0.684,0.146 10 CANL*f 0.703,1.323 1.387,1.470 0.684,0.146 10 CANL*e 0.772,1.524 1.455,1.671 0.684,0.146 10 CANL*d 2.586,0.831 2.936,0.973 0.350,0.142 10 E152 1.498,1.022 1.303,1.207 1.303,1.207 1.189,1.207 false 2.18,1.476 1.99,1.476 1.99,1.476 1.724,1.022 false 1.512,0.854 1.317,0.683 1.317,0.683 1.203,0.683 false 1.379,0.106 1.555,0.106 1.555,0.106 1.724,0.868 false 1.191,0.472 1.348,0.472 1.348,0.472 1.586,0.862 false 1.224,1.408 1.382,1.408 1.382,1.408 1.572,1.019 false 6.081,0.85 6.350,0.992 0.269,0.142 10 E22 5.112,0.747 4.819,0.388 4.819,0.388 4.724,0.388 false 4.477,0.309 4.765,0.451 0.288,0.142 10 CG

Text in Illustration
*a Rear view of wire harness connector
(to No. 5 CAN Junction Connector)
*b Front view of DLC3
*c to Central Gateway ECU *d to Bus Buffer ECU (w/ Bus Buffer ECU)
*e
·

to Multi-media Module Receiver Assembly (for Multi-media Module Receiver Type)

·

to Radio and Display Receiver Assembly (for Radio and Display Type)


*f to No. 6 CAN Junction Connector


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E152-8 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU
E152-19 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E152-9 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Bus buffer ECU*1
E152-20 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E152-10 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
·

Multi-media module receiver assembly*2

·

Radio and display receiver assembly*3


E152-21 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E152-11 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 6 CAN junction connector
E152-22 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


*1: w/ Bus Buffer ECU

*2: for Multi-media Module Receiver Type

*3: for Radio and Display Type


Result
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (No. 6 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)

C

6.CONNECT CONNECTOR

D

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
6.CONNECT CONNECTOR
a.

Reconnect the E152 No. 5 CAN junction connector.



NEXT

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)
7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 6 CAN junction connector.

U165519E01
0.051,0.046 0.346,0.271 0.295,0.225 10 *a 4.217,0.046 4.512,0.271 0.295,0.225 10 *b 0.914,0.157 1.597,0.308 0.684,0.151 10 CANH*c 0.962,1.468 1.646,1.615 0.684,0.146 10 CANL*c 0.71,0.403 1.393,0.554 0.684,0.151 10 CANH*d 0.746,1.235 1.430,1.381 0.684,0.146 10 CANL*d 2.607,0.831 2.874,0.973 0.267,0.142 10 F99 1.257,0.472 1.415,0.472 1.415,0.472 1.813,0.862 false 1.268,1.309 1.426,1.309 1.426,1.309 1.799,1.019 false 6.081,0.85 6.350,0.992 0.269,0.142 10 E22 5.117,0.757 4.824,0.397 4.824,0.397 4.729,0.397 false 4.481,0.318 4.769,0.460 0.288,0.142 10 CG

Text in Illustration
*a Rear view of wire harness connector
(to No. 6 CAN Junction Connector)
*b Front view of DLC3
*c to No. 5 CAN Junction Connector *d to No. 2 CAN Junction Terminal


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
F99-6 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 5 CAN junction connector
F99-17 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F99-7 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 2 CAN junction terminal
F99-18 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Result
Result Proceed to
OK A
NG (No. 5 CAN junction connector CAN main wire) B
NG (No. 2 CAN junction terminal CAN main wire) C



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.
U165619E02
1.417,1.146 1.063,1.76 1.063,1.76 0.938,1.76 false 1.396,1.01 0.99,0.542 0.99,0.542 0.854,0.542 false 1.615,3.052 1.406,2.656 1.406,2.656 1.292,2.656 false 0.052,0.052 0.375,0.281 0.323,0.229 10 false *a 0.052,2.281 0.406,2.5 0.354,0.219 10 false *b 1.521,0.281 2,0.5 0.479,0.219 10 false E145 0.208,3.24 0.615,3.51 0.406,0.271 10 false E22 0.542,1.656 1.052,1.865 0.51,0.208 10 false CA3L 0.427,0.458 0.927,0.656 0.5,0.198 10 false CA3H 1.031,2.573 1.417,2.76 0.385,0.188 10 false CG

Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-6 (CA3H) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-21 (CA3L) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Component with harness connected
(Central Gateway ECU)
*b Front view of DLC3

HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR