Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Check Bus 5 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus wires and GND when no resistance exists between terminal 15 (CA5H) of the central gateway ECU and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU and terminal 4 (CG) of the DLC3.

Detection Item Trouble Area
No resistance exists between terminal 15 (CA5H) of the central gateway ECU and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU and terminal 4 (CG) of the DLC3.
·

Short to GND in bus 5 CAN main wires

·

Short to GND in bus 5 CAN branch wires

·

Central gateway ECU

·

Driving support ECU assembly*1

·

Millimeter wave radar sensor assembly*1

·

Forward recognition camera*1

·

Inner rear view mirror assembly*2, *7

·

Blind spot monitor sensor LH*3

·

Clearance warning ECU assembly*4

·

Parking assist ECU*5

·

Suspension control ECU*6

·

No. 3 CAN junction connector

·

No. 4 CAN junction connector

·

No. 1 CAN junction terminal



*1: w/ Pre-crash Safety System

*2: w/o Pre-crash Safety System

*3: w/ Blind Spot Monitor System

*4: w/ TOYOTA Parking Assist-sensor System

*5: w/ Multi-terrain Monitor System

*6: w/ Active Height Control Suspension

*7: w/ Automatic High Beam System


WIRING DIAGRAM

C334462E08
5.615,1.615 6.063,1.813 0.448,0.198 10 false E145 5.604,1.771 7.042,1.969 1.438,0.198 10 false Central Gateway ECU 5.969,0.563 6.521,0.781 0.552,0.219 10 false CA5H 5.99,1.323 6.542,1.542 0.552,0.219 10 false CA5L 5.729,1.104 6.281,1.323 0.552,0.219 10 false 16 5.719,0.573 6.271,0.792 0.552,0.219 10 false 15 4.115,1.083 4.667,1.302 0.552,0.219 10 false 15 4.115,0.563 4.667,0.781 0.552,0.219 10 false 5 3.135,1.094 3.688,1.313 0.552,0.219 10 false 14 3.208,0.552 3.76,0.771 0.552,0.219 10 false 4 0.885,0.667 1.375,0.875 0.49,0.208 10 false CA2H 0.906,1.177 1.354,1.354 0.448,0.177 10 false CA2L 1.385,0.573 1.938,0.792 0.552,0.219 10 false 10 1.375,1.104 1.927,1.323 0.552,0.219 10 false 11 0.25,1.615 0.802,1.833 0.552,0.219 10 false E164 0.26,1.771 2.479,1.979 2.219,0.208 10 false Driving Support ECU Assembly*1 5.979,2.708 6.531,2.927 0.552,0.219 10 false CA2H 5.979,3.229 6.531,3.448 0.552,0.219 10 false CA2L 5.75,3.125 5.969,3.313 0.219,0.188 10 false 2 5.771,2.604 6,2.792 0.229,0.188 10 false 3 5.563,3.625 6.146,3.896 0.583,0.271 10 false A72 5.563,3.813 7.094,4.438 1.531,0.625 10 false Millimeter Wave Radar Sensor Assembly*1 4.104,2.604 4.656,2.823 0.552,0.219 10 false 6 4.104,3.146 4.656,3.365 0.552,0.219 10 false 16 3.188,2.604 3.74,2.823 0.552,0.219 10 false 7 3.115,3.146 3.667,3.365 0.552,0.219 10 false 17 1.406,2.604 1.958,2.823 0.552,0.219 10 false 17 1.396,3.125 1.948,3.344 0.552,0.219 10 false 18 0.24,3.646 0.604,3.854 0.365,0.208 10 false F92 0.24,3.813 1.813,4.188 1.573,0.375 10 false Clearance Warning ECU Assembly*3 1.063,2.708 1.333,2.896 0.271,0.188 10 false R1 1.052,3.229 1.344,3.438 0.292,0.208 10 false R2 3.104,5.177 3.656,5.396 0.552,0.219 10 false 19 3.177,4.656 3.729,4.875 0.552,0.219 10 false 9 4.115,5.188 4.667,5.406 0.552,0.219 10 false 18 4.115,4.646 4.667,4.865 0.552,0.219 10 false 8 5.979,4.74 6.531,4.958 0.552,0.219 10 false CANH 5.979,5.281 6.531,5.5 0.552,0.219 10 false CANL 5.708,4.656 5.979,4.865 0.271,0.208 10 false 40 5.688,5.188 5.958,5.375 0.271,0.188 10 false 39 5.646,5.656 6.01,5.854 0.365,0.198 10 false F76 5.646,5.813 7.125,6.063 1.479,0.25 10 false Parking Assist ECU*4 2.875,7.385 3.302,7.552 0.427,0.167 10 false E151 2.875,7.542 5.063,7.76 2.188,0.219 10 false No. 3 CAN Junction Connector 0.104,8.427 2.719,8.635 2.615,0.208 10 false *2: w/o Pre-crash Safety System 0.104,8.063 2.781,8.396 2.677,0.333 10 false *1: w/ Pre-crash Safety System 4.135,6.323 4.688,6.542 0.552,0.219 10 false 3 4.104,6.875 4.656,7.094 0.552,0.219 10 false 13 1.406,5.198 1.958,5.417 0.552,0.219 10 false 11 1.406,4.667 1.958,4.885 0.552,0.219 10 false 5 0.948,4.719 1.5,4.938 0.552,0.219 10 false CA1P 0.938,5.26 1.49,5.479 0.552,0.219 10 false CA1N 0.271,5.667 0.646,5.875 0.375,0.208 10 false R20 0.271,5.833 2.271,6.031 2,0.198 10 false Forward Recognition Camera*1 0.219,7.375 0.604,7.573 0.385,0.198 10 false R16 0.219,7.521 2.781,7.927 2.563,0.406 10 false Inner Rear View Mirror Assembly*2, *5 0.875,6.448 1.375,6.656 0.5,0.208 10 false CANH 0.885,6.99 1.365,7.198 0.479,0.208 10 false CANL 1.406,6.344 1.958,6.563 0.552,0.219 10 false 9 1.396,6.885 1.948,7.104 0.552,0.219 10 false 10 2.25,8.083 4.927,8.417 2.677,0.333 10 false *3: w/ TOYOTA Parking Assist System 2.25,8.417 4.927,8.75 2.677,0.333 10 false *4: w/ Multi-terrain Monitor System 4.76,8.083 7.156,8.406 2.396,0.323 10 false *5: w/ Automatic High Beam System

C334617E01
5.198,3.786 6.604,3.949 1.406,0.163 10 K50 0.149,3.824 1.555,3.986 1.406,0.163 10 K34 5.198,3.95 7.067,4.113 1.869,0.163 10 No. 1 CAN Junction Terminal 5.926,3.529 6.740,3.692 0.813,0.163 10 CANL 0.85,3.427 1.663,3.590 0.813,0.163 10 CANL 5.926,2.815 6.740,2.978 0.813,0.163 10 CANH 0.817,2.899 1.631,3.062 0.813,0.163 10 CANH 5.735,2.801 6.548,2.964 0.813,0.163 10 3 5.735,3.333 6.548,3.496 0.813,0.163 10 2 2.741,3.863 4.736,4.152 1.995,0.289 10 No. 4 CAN Junction Connector 0.177,2.042 1.583,2.205 1.406,0.163 10 r2 0.177,2.206 2.256,2.498 2.078,0.292 10 Blind Spot Monitor Sensor LH*1 1.34,0.996 2.154,1.159 0.813,0.163 10 2 1.34,1.528 2.154,1.691 0.813,0.163 10 7 1.354,2.812 2.168,2.975 0.813,0.163 10 7 1.354,3.34 2.168,3.503 0.813,0.163 10 8 0.841,1.071 1.654,1.233 0.813,0.163 10 CA1P 0.841,1.603 1.654,1.766 0.813,0.163 10 CA1N 3.008,1.416 3.821,1.579 0.813,0.163 10 2 2.928,1.099 3.741,1.261 0.813,0.163 10 K58 2.928,1.622 3.741,1.785 0.813,0.163 10 K58 3.008,0.893 3.821,1.056 0.813,0.163 10 1 4.175,1.416 4.988,1.579 0.813,0.163 10 2 4.096,1.099 4.909,1.261 0.813,0.163 10 K56 4.096,1.622 4.909,1.785 0.813,0.163 10 K56 4.175,0.893 4.988,1.056 0.813,0.163 10 1 3.012,3.2 3.826,3.363 0.813,0.163 10 2 2.933,2.911 3.746,3.073 0.813,0.163 10 K65 2.933,3.435 3.746,3.597 0.813,0.163 10 K65 3.012,2.677 3.826,2.840 0.813,0.163 10 1 4.175,3.214 4.988,3.377 0.813,0.163 10 2 4.096,2.911 4.909,3.073 0.813,0.163 10 K57 4.096,3.435 4.909,3.597 0.813,0.163 10 K57 4.175,2.677 4.988,2.840 0.813,0.163 10 1 0.266,4.872 3.056,5.035 2.790,0.163 10 *1: w/ Blind Spot Monitor System 0.266,5.171 3.056,5.334 2.790,0.163 10 *2: w/ Active Height Control System 0.145,3.987 2.009,4.233 1.864,0.246 10 Suspension Control ECU*2

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 3 CAN JUNCTION CONNECTOR)
a.
U165649E02
0.635,2.073 0.896,2.073 0.896,2.073 1.365,1.49 false 1.229,2.271 1.583,2.271 1.583,2.271 1.521,1.49 false 1.615,3.125 1.354,2.625 1.354,2.625 1.24,2.625 false 0.073,0.052 0.396,0.281 0.323,0.229 10 false *a 0.073,2.406 0.417,2.625 0.344,0.219 10 false *b 1.5,0.406 2,0.635 0.5,0.229 10 false E145 0.208,3.417 0.688,3.698 0.479,0.281 10 false E22 0.813,2.188 1.375,2.406 0.563,0.219 10 false CA5L 0.177,1.979 0.688,2.167 0.51,0.188 10 false CA5H 0.969,2.542 1.302,2.75 0.333,0.208 10 false CG

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the central gateway ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-15 (CA5H) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-16 (CA3L) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU)
*b Front view of DLC3



OK

NG

2.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the E145 central gateway ECU connector.



NEXT

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
a.
U165525E02
1.406,0.823 1.208,0.531 1.208,0.531 1.094,0.531 false 1.323,0.26 1.594,0.26 1.594,0.26 1.708,0.823 false 1.656,2.427 1.302,1.99 1.302,1.99 1.188,1.99 false 0.063,0.052 0.292,0.323 0.229,0.271 10 false *a 0.063,1.635 0.292,1.906 0.229,0.271 10 false *b 0.448,0.948 0.854,1.188 0.406,0.24 10 false K50 0.594,0.438 1.115,0.677 0.521,0.24 10 false CANH 0.875,0.188 1.427,0.458 0.552,0.271 10 false CANL 0.417,2.594 0.813,2.865 0.396,0.271 10 false E22 0.896,1.917 1.292,2.135 0.396,0.219 10 false CG

Disconnect the No. 1 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K50-3 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
K50-2 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 CAN Junction Terminal)
*b Front view of DLC3



OK

REPLACE NO. 1 CAN JUNCTION TERMINAL

NG

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the K50 No. 1 CAN junction terminal connector.



NEXT

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 3 CAN junction connector.

U165494E01
0.113,0.045 0.339,0.215 0.225,0.170 10 *a 4.662,0.045 4.887,0.215 0.225,0.170 10 *b 0.507,0.833 0.850,0.975 0.343,0.142 10 E151 0.438,0.39 1.008,0.534 0.569,0.144 10 CANH*c 0.659,1.221 1.228,1.364 0.569,0.144 10 CANL*c 0.846,1.404 1.416,1.548 0.569,0.144 10 CANL*d 1.402,1.474 1.594,1.474 1.594,1.474 1.867,0.999 false 1.076,1.595 1.645,1.739 0.569,0.144 10 CANL*e 2.653,1.594 3.222,1.738 0.569,0.144 10 CANL*f 0.836,0.066 1.405,0.210 0.569,0.144 10 CANH*e 0.577,0.224 1.146,0.367 0.569,0.144 10 CANH*d 2.734,0.062 3.304,0.205 0.569,0.144 10 CANH*f 3.481,0.603 4.050,0.746 0.569,0.144 10 CANH*i 2.974,0.235 3.544,0.379 0.569,0.144 10 CANH*g 3.23,0.389 3.799,0.533 0.569,0.144 10 CANH*h 3.498,1.059 4.067,1.203 0.569,0.144 10 CANL*i 3.034,1.417 3.603,1.561 0.569,0.144 10 CANL*g 2.71,0.839 3.104,0.455 3.104,0.455 3.203,0.455 false 2.317,0.844 2.614,0.131 2.614,0.131 2.712,0.131 false 1.174,0.289 1.367,0.289 1.367,0.289 1.867,0.847 false 1.391,0.142 1.633,0.142 1.633,0.142 2.047,0.836 false 2.519,0.826 2.734,0.301 2.734,0.301 2.948,0.301 false 2.71,1.007 3.038,1.314 3.038,1.314 3.136,1.314 false 2.317,1.003 2.531,1.664 2.531,1.664 2.629,1.664 false 2.932,0.839 3.353,0.683 3.353,0.683 3.451,0.683 false 2.932,1.007 3.383,1.15 3.383,1.15 3.481,1.15 false 1.643,0.839 1.127,0.466 1.127,0.466 1.029,0.466 false 1.643,1.007 1.312,1.286 1.312,1.286 1.214,1.286 false 1.402,1.474 1.594,1.474 1.594,1.474 1.867,0.999 false 1.612,1.656 1.853,1.656 1.853,1.656 2.047,1.01 false 3.15,1.249 3.719,1.393 0.569,0.144 10 CANL*h 2.519,1.02 2.798,1.504 2.798,1.504 3.011,1.504 false 5.52,0.165 5.792,0.313 0.272,0.148 10 E22 4.89,0.254 5.242,0.397 0.352,0.144 10 CG 5.586,0.655 5.346,0.324 5.346,0.324 5.132,0.324 false

Text in Illustration
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b Front view of DLC3
*c to No. 4 CAN Junction Connector *d to Driving Support ECU Assembly (w/ Pre-crash Safety System)
*e to Central Gateway ECU *f to Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System)
*g to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System) *h to Parking Assist ECU (w/ Multi-terrain Monitor System)
*i
·

to Forward Recognition Camera (w/ Pre-crash Safety System)

·

to Inner Rear View Mirror Assembly (w/o Pre-crash Safety System, w/ Automatic High Beam System)


- -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E151-3 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 4 CAN junction connector
E151-13 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E151-4 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Driving support ECU assembly*1
E151-14 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E151-5 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU
E151-15 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E151-6 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*1
E151-16 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E151-7 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Clearance warning ECU assembly*3
E151-17 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E151-8 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Parking assist ECU*4
E151-18 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E151-9 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
·

Forward recognition camera*1

·

Inner rear view mirror assembly*2, *5


E151-19 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


*1: w/ Pre-crash Safety System

*2: w/o Pre-crash Safety System

*3: w/ TOYOTA Parking Assist-sensor System

*4: w/ Multi-terrain Monitor System

*5: w/ Automatic High Beam System


Result
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (No. 4 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)

C

6.CONNECT CONNECTOR

D

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
6.CONNECT CONNECTOR
a.

Reconnect the E151 No. 3 CAN junction connector.



NEXT

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 4 CAN junction connectors.

U165625E01
3.337,3.028 3.531,3.192 3.531,3.192 3.681,3.192 false 3.337,2.883 3.531,2.719 3.531,2.719 3.681,2.719 false 3.716,2.646 4.445,2.899 0.729,0.253 10 CANH 2.529,2.39 3.258,2.643 0.729,0.253 10 *a 3.716,3.125 4.445,3.379 0.729,0.253 10 CANL 1.347,2.787 2.076,2.933 0.729,0.145 10 K57 1.347,3.243 2.076,3.388 0.729,0.145 10 K56 1.347,1.894 2.076,2.040 0.729,0.145 10 K58 1.347,1.642 2.076,1.788 0.729,0.145 10 K65 0.085,0.072 0.813,0.217 0.729,0.145 10 *1 4.616,2.299 5.345,2.552 0.729,0.253 10 *b 5.627,2.235 5.900,2.375 0.272,0.140 10 E22 5.675,2.757 5.38,2.397 5.38,2.397 5.23,2.397 false 4.982,2.315 5.485,2.569 0.503,0.253 10 CG

Text in Illustration
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Code Color (CANH Side) Color (CANL Side) Connect to
K56 W B No. 3 CAN Junction Connector
K57 SB B No. 1 CAN Junction Terminal
K58 R B Blind Spot Monitor Sensor LH*1
K65 L B Suspension Control ECU*2

*1: w/ Blind Spot Monitor System

*2: w/ Active Height Control Suspension


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K56-1 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
K56-2 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
K57-1 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
K57-2 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
K58-1 (CANH) - E22-4 (CG)*1 Cable disconnected from negative (-) battery terminal 200 Ω or higher
K58-2 (CANL) - E22-4 (CG)*1 Cable disconnected from negative (-) battery terminal 200 Ω or higher
K65-1 (CANH) - E22-4 (CG)*2 Cable disconnected from negative (-) battery terminal 200 Ω or higher
K65-2 (CANL) - E22-4 (CG)*2 Cable disconnected from negative (-) battery terminal 200 Ω or higher


*1: w/ Blind Spot Monitor System

*2: w/ Active Height Control Suspension


Result
Result Proceed to
OK A
NG (No. 3 CAN junction connector CAN main wire) B
NG (No. 1 CAN junction terminal CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)

D

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.
U165621E02
1.625,3.073 1.365,2.573 1.365,2.573 1.25,2.573 false 1.927,1.135 2.5,1.667 2.5,1.667 2.615,1.667 false 1.844,1.135 2.094,1.927 2.094,1.927 2.208,1.927 false 0.052,0.063 0.5,0.406 0.448,0.344 10 false *a 0.052,2.281 0.458,2.51 0.406,0.229 10 false *b 1.531,0.281 2.021,0.51 0.49,0.229 10 false E145 0.219,3.24 0.646,3.5 0.427,0.26 10 false E22 0.958,2.49 1.313,2.688 0.354,0.198 10 false CG 2.24,1.833 2.813,2.063 0.573,0.229 10 false CA5L 2.656,1.573 3.208,1.813 0.552,0.24 10 false CA5H

Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-15 (CA5H) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E145-16 (CA5L) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Component with harness connected
(Central Gateway ECU)
*b Front view of DLC3

HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR