After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Turn the ignition switch off before measuring the resistances between CAN main wires and between CAN branch wires.
Turn the ignition switch off before inspecting CAN wires for a ground short.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
JUNCTION CONNECTOR
NO. 1 CAN JUNCTION CONNECTOR
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | for No. 2 CAN Junction Connector |
| *c | for 4WD Control ECU | *d | for Power Steering ECU Assembly (w/ Variable Flow Control Solenoid Valve) |
| *e | for Airbag Sensor Assembly | *f | for Tire Pressure Warning ECU (w/ Tire Pressure Warning System) |
| *g | for Bus Buffer ECU (w/ Bus Buffer ECU) | *h | for ECM |
| *i | for Air Conditioning Amplifier Assembly | - | - |
| No. 1 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
| E135-1 (CANH) | SB | No. 2 CAN junction connector |
| E135-11 (CANL) | W | |
| E135-2 (CANH) | P | 4WD control ECU |
| E135-12 (CANL) | W | |
| E135-3 (CANH) | LG | Power steering ECU assembly*1 |
| E135-13 (CANL) | W | |
| E135-4 (CANH) | GR | Airbag sensor assembly |
| E135-14 (CANL) | W | |
| E135-5 (CANH) | R | Tire pressure warning ECU*2 |
| E135-15 (CANL) | W | |
| E135-6 (CANH) | BE | Bus buffer ECU*3 |
| E135-16 (CANL) | W | |
| E135-7 (CANH) | V | ECM |
| E135-17 (CANL) | W | |
| E135-8 (CANH) | G | Air conditioning amplifier assembly |
| E135-18 (CANL) | W |
*1: w/ Variable Flow Control Solenoid Valve
*2: w/ Tire Pressure Warning System
*3: w/ Bus Buffer ECU
NO. 2 CAN JUNCTION CONNECTOR
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | for No. 1 CAN Junction Connector |
| *c | for Main Body ECU (Multiplex Network Body ECU) | *d | for Master Cylinder Solenoid (Skid Control ECU) |
| *e | for Headlight Leveling ECU Assembly | *f | ·
for Multi-media Module Receiver Assembly (for Multi-media Module Receiver Type) ·
for Radio and Display Receiver Assembly (for Radio and Display Type) |
| *g | for Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) | *h | for Combination Meter Assembly |
| *i | for Steering control ECU (w/ Variable Gear Ratio Steering System) | *j | for DLC3 |
| *k | for Steering Sensor | - | - |
| No. 2 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
| E133-1 (CANH) | SB | No. 1 CAN junction connector |
| E133-11 (CANL) | W | |
| E133-2 (CANH) | G | Main body ECU (multiplex network body ECU) |
| E133-12 (CANL) | W | |
| E133-3 (CANH) | L | Master cylinder solenoid (skid control ECU) |
| E133-13 (CANL) | W | |
| E133-4 (CANH) | LG | Headlight leveling ECU assembly |
| E133-14 (CANL) | B | |
| E133-5 (CANH) | G | ·
Multi-media module receiver assembly*1 ·
Radio and display receiver assembly*2 |
| E133-15 (CANL) | GR | |
| E133-6 (CANH) | B | Certification ECU (smart key ECU assembly)*3 |
| E133-16 (CANL) | W | |
| E133-7 (CANH) | BE | Combination meter assembly |
| E133-17 (CANL) | W | |
| E133-8 (CANH) | R | Steering control ECU*4 |
| E133-18 (CANL) | W | |
| E133-9 (CANH) | LG | DLC3 |
| E133-19 (CANL) | W | |
| E133-10 (CANH) | GR | Steering sensor |
| E133-20 (CANL) | W |
*1: for Multi-media Module Receiver Type
*2: for Radio and Display Type
*3: w/ Entry and Start System
*4: w/ Variable Gear Ratio Steering System
NO. 7 CAN JUNCTION CONNECTOR
| *a | Rear view of wire harness connector
(to No. 7 CAN Junction Connector) |
*b | for No. 8 CAN Junction Connector |
| *c | for Main Body ECU (Multiplex Network Body ECU) | *d | for Outer Mirror Control ECU Assembly LH (w/ Memory) |
| *e | for Power Seat Switch Assembly (w/ Memory) | *f | for Multiplex Tilt and Telescopic ECU (w/ Power Tilt and Power Telescopic Steering Column System) |
| No. 7 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
| E134-1 (CANH) | W | No. 8 CAN junction connector |
| E134-12 (CANL) | L | |
| E134-2 (CANH) | GR | Main body ECU (multiplex network body ECU) |
| E134-13 (CANL) | L | |
| E134-3 (CANH) | BE | Outer mirror control ECU assembly LH*1 |
| E134-14 (CANL) | L | |
| E134-4 (CANH) | V | Power seat switch assembly*1 |
| E134-15 (CANL) | L | |
| E134-5 (CANH) | P | Multiplex Tilt and Telescopic ECU*2 |
| E134-16 (CANL) | L |
*1: w/ Memory
*2: w/ Power Tilt and Power Telescopic Steering Column System
NO. 8 CAN JUNCTION CONNECTOR
| *a | Rear view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | for No. 7 CAN Junction Connector |
| *c | for No. 9 CAN Junction Connector | *d | for Outer Mirror Control ECU Assembly RH (w/ Memory) |
| No. 8 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
| E136-1 (CANH) | W | No. 7 CAN junction connector |
| E136-12 (CANL) | L | |
| E136-2 (CANH) | W | No. 9 CAN junction connector |
| E136-13 (CANL) | L | |
| E136-3 (CANH) | LG | Outer mirror control ECU assembly RH* |
| E136-14 (CANL) | L |
*: w/ Memory
NO. 9 CAN JUNCTION CONNECTOR
| *a | Rear view of wire harness connector
(to No. 9 CAN Junction Connector) |
*b | for No. 8 CAN Junction Connector |
| *c | No. 3 CAN Junction Terminal | *d | for Power Back Door Unit Assembly (Power Back Door ECU) (w/ Power Back Door System) |
| *e | for No. 2 Main Body ECU (w/ Tail Gate Closer System) | - | - |
| No. 9 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
| L71-1 (CANH) | W | No. 8 CAN junction connector |
| L71-12 (CANL) | L | |
| L71-2 (CANH) | W | No. 3 CAN junction terminal |
| L71-13 (CANL) | L | |
| L71-3 (CANH) | V | Power back door unit assembly (power back door ECU)*1 |
| L71-14 (CANL) | L | |
| L71-4 (CANH) | LG | No. 2 main body ECU*2 |
| L71-15 (CANL) | L |
*1: w/ Power Back Door System
*2: w/ Tail Gate Closer System
NO. 3 CAN JUNCTION TERMINAL
| *a | Rear view of wire harness connector
(to No. 3 CAN Junction Terminal) |
| No. 3 CAN Junction Terminal | Wiring Color | Connect to |
|---|---|---|
| L69-3 (CANH) | W | No. 9 CAN junction connector |
| L69-2 (CANL) | L |
CHECK DLC3
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.
| *a | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E22-6 (CANH) - E22-14 (CANL) | LG - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E22-6 (CANH) - E22-4 (CG) | LG - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E22-14 (CANL) - E22-4 (CG) | W - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E22-6 (CANH) - E22-16 (BAT) | LG - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E22-14 (CANL) - E22-16 (BAT) | W - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK ECM
| *A | for 1UR-FE, 1GR-FE | *B | for 3UR-FE |
| *C | for 1VD-FTV | - | - |
| *a | Component without harness connected
(ECM) |
- | - |
Disconnect the ECM connectors.
| *A | for 1UR-FE, 1GR-FE | *B | for 3UR-FE |
| *C | for 1VD-FTV | - | - |
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| A38-10 (CANH) - A38-11 (CANL) | V - W | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A38-10 (CANH) - C45-81 (E1) | V - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A38-11 (CANL) - C45-81 (E1) | W - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A38-10 (CANH) - A38-1 (BATT) | V - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A38-11 (CANL) - A38-1 (BATT) | W - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| A38-11 (CANH) - A38-19 (CANL) | V - W | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A38-11 (CANH) - C45-81 (E1) | V - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A38-19 (CANL) - C45-81 (E1) | W - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A38-11 (CANH) - A38-1 (BATT) | V - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A38-19 (CANL) - A38-1 (BATT) | W - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| A38-41 (CANH) - A38-49 (CANL) | V - W | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A38-41 (CANH) - C45-81 (E1) | V - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A38-49 (CANL) - C45-81 (E1) | W - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A38-41 (CANH) - A38-20 (BATT) | V - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A38-49 (CANL) - A38-20 (BATT) | W - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK MASTER CYLINDER SOLENOID (SKID CONTROL ECU)
| *a | Component without harness connected
(Master Cylinder Solenoid [Skid Control ECU]) |
- | - |
Disconnect the master cylinder solenoid (skid control ECU) connector.
| *a | Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU]) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| A24-11 (CANH) - A24-25 (CANL) | L - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A24-11 (CANH) - A24-1 (GND1) | L - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A24-25 (CANL) - A24-1 (GND1) | W - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A24-11 (CANH) - A24-2 (+BM1) | L - B | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A24-25 (CANL) - A24-2 (+BM1) | W - B | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)
| *a | Component without harness connected
(Air Conditioning Amplifier Assembly) |
- | - |
Disconnect the air conditioning amplifier assembly connectors.
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Condition | Specified Condition |
|---|---|---|---|
| E35-3 (CANH) - E35-4 (CANL) | G - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E35-3 (CANH) - E36-1 (GND) | G - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E35-4 (CANL) - E36-1 (GND) | W - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E35-3 (CANH) - E36-6 (+B1) | G - LG | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E35-4 (CANL) - E36-6 (+B1) | W - LG | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)
| *a | Component without harness connected
(Air Conditioning Amplifier Assembly) |
- | - |
Disconnect the air conditioning amplifier assembly connector.
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Condition | Specified Condition |
|---|---|---|---|
| E81-11 (CANH) - E81-12 (CANL) | G - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E81-11 (CANH) - E81-14 (GND) | G - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E81-12 (CANL) - E81-14 (GND) | W - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E81-11 (CANH) - E81-21 (+B1) | G - LG | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E81-12 (CANL) - E81-21 (+B1) | W - LG | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK COWL SIDE JUNCTION BLOCK LH AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main Body ECU (Multiplex Network Body ECU) with 2 Connectors | *B | Bus 2 |
| *C | Sub Bus 1 | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
| *A | Main Body ECU (Multiplex Network Body ECU) with 3 Connectors | *B | Bus 2 |
| *C | Sub Bus 1 | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL).
| *A | Bus 2 | *B | Sub Bus 1 |
| *a | Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
*b | Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
Reconnect the cowl side junction block LH connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E118-14 (CANH) - E118-13 (CANL) | G - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E118-14 (CANH) - A-11 (GND1) | G - None | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E118-13 (CANL) - A-11 (GND1) | W - None | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E118-14 (CANH) - A-31 (BECU) | G - None | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E118-13 (CANL) - A-31 (BECU) | W - None | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E117-9 (CANP) - E117-10 (CANN) | GR - L | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| E117-9 (CANP) - A-11 (GND1) | GR - None | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E117-10 (CANN) - A-11 (GND1) | L - None | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E117-9 (CANP) - A-31 (BECU) | GR - None | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E117-10 (CANN) - A-31 (BECU) | L - None | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK COMBINATION METER ASSEMBLY
| *a | Component without harness connected
(Combination Meter Assembly) |
- | - |
Disconnect the combination meter assembly connector.
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E119-39 (CANH) - E119-40 (CANL) | BE - W | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| E119-39 (CANH) - E119-20 (ET) | BE - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E119-40 (CANL) - E119-20 (ET) | W - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E119-39 (CANH) - E119-21 (B) | BE - V | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E119-40 (CANL) - E119-21 (B) | W - V | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK AIRBAG SENSOR ASSEMBLY
| *a | Component without harness connected
(Airbag Sensor Assembly) |
- | - |
Disconnect the airbag sensor assembly connector.
| *a | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E47-13 (CANH) - E47-22 (CANL) | GR - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E47-13 (CANH) - E47-25 (E1) | GR - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E47-22 (CANL) - E47-25 (E1) | W - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E47-13 (CANH) - E22-16 (BAT) | GR - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E47-22 (CANL) - E22-16 (BAT) | W - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY (for Multi-media Module Receiver Type)
| *a | Component without harness connected
(Multi-media Module Receiver Assembly) |
- | - |
Disconnect the multi-media module receiver assembly connector.
| *a | Front view of wire harness connector
(to Multi-media Module Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| F77-1 (CANH) - F77-2 (CANL) | G - GR | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F77-1 (CANH) - F77-12 (GND1) | G - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F77-2 (CANL) - F77-12 (GND1) | GR - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F77-1 (CANH) - F77-17 (+B1) | G - V | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F77-2 (CANL) - F77-17 (+B1) | GR - V | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)
| *a | Component without harness connected
(Radio and Display Receiver Assembly) |
- | - |
Disconnect the radio and display receiver assembly connectors.
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| F124-9 (CANH) - F124-10 (CANL) | G - GR | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F124-9 (CANH) - F120-7 (GND1) | G - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F124-10 (CANL) - F120-7 (GND1) | GR - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F124-9 (CANH) - F120-4 (+B1) | G - V | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F124-10 (CANL) - F120-4 (+B1) | GR - V | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK STEERING SENSOR
| *A | w/o Variable Gear Ratio Steering System, w/o Entry and Start System | *B | w/o Variable Gear Ratio Steering System, w/ Entry and Start System |
| *C | w/ Variable Gear Ratio Steering System | - | - |
| *a | Component without harness connected
(Steering Sensor) |
- | - |
Disconnect the steering sensor connector.
| *A | w/o Variable Gear Ratio Steering System, w/o Entry and Start System | *B | w/o Variable Gear Ratio Steering System, w/ Entry and Start System |
| *C | w/ Variable Gear Ratio Steering System | - | - |
| *a | Front view of wire harness connector
(to Steering Sensor) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E181-4 (CANH) - E181-3 (CANL) | GR - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E181-4 (CANH) - E181-2 (ESS) | GR - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E181-3 (CANL) - E181-2 (ESS) | W - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E181-4 (CANH) - E181-6 (BAT) | GR - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E181-3 (CANL) - E181-6 (BAT) | W - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E121-3 (CANH) - E121-2 (CANL) | GR - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E121-3 (CANH) - E121-1 (ESS) | GR - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E121-2 (CANL) - E121-1 (ESS) | W - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E121-3 (CANH) - E121-5 (BAT) | GR - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E121-2 (CANL) - E121-5 (BAT) | W - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E163-3 (CANH) - E163-2 (CANL) | GR - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E163-3 (CANH) - E163-1 (ESS) | GR - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E163-2 (CANL) - E163-1 (ESS) | W - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E163-3 (CANH) - E163-5 (BAT) | GR - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E163-2 (CANL) - E163-5 (BAT) | W - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK 4WD CONTROL ECU
| *a | Component without harness connected
(4WD Control ECU) |
- | - |
Disconnect the 4WD control ECU connectors.
| *a | Front view of wire harness connector
(to 4WD Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| A27-20 (CANH) - A27-40 (CANL) | P - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A27-20 (CANH) - A28-10 (GND) | P - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A27-40 (CANL) - A28-10 (GND) | W - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A27-20 (CANH) - A27-21 (+B) | P - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A27-40 (CANL) - A27-21 (+B) | W - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK TIRE PRESSURE WARNING ECU (w/ Tire Pressure Warning System)
| *A | w/o Front Antenna |
| *B | w/ Front Antenna |
| *a | Component without harness connected
(Tire Pressure Warning ECU) |
w/o Front Antenna:
| *a | Front view of wire harness connector
(to Tire Pressure Warning ECU) |
Disconnect the tire pressure warning ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| L65-9 (CANH) - L65-10 (CANL) | R - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| L65-9 (CANH) - L65-12 (GND) | R - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| L65-10 (CANL) - L65-12 (GND) | W - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| L65-9 (CANH) - L65-7 (+B) | R - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L65-10 (CANL) - L65-7 (+B) | W - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
w/ Front Antenna:
| *a | Front view of wire harness connector
(to Tire Pressure Warning ECU) |
| *b | Front view DLC3 |
Disconnect the tire pressure warning ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| L75-9 (CANH) - L75-10 (CANL) | R - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| L75-9 (CANH) - L75-12 (GND) | R - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| L75-10 (CANL) - L75-12 (GND) | W - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| L75-9 (CANH) - E22-16 (BAT) | R - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L75-10 (CANL) - E22-16 (BAT) | W - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK STEERING CONTROL ECU (w/ Variable Gear Ratio Steering System)
| *a | Component without harness connected
(Steering Control ECU) |
- | - |
Disconnect the steering control ECU connectors.
| *a | Front view of wire harness connector
(to Steering Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E161-3 (CNH1) - E161-9 (CNL1) | R - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E161-3 (CNH1) - E159-1 (PGND) | R - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E161-9 (CNL1) - E159-1 (PGND) | W - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E161-3 (CNH1) - E161-7 (+BI) | R - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E161-9 (CNL1) - E161-7 (+BI) | W - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK POWER STEERING ECU ASSEMBLY (w/ Variable Flow Control Solenoid Valve)
| *a | Component without harness connected
(Power Steering ECU Assembly) |
Disconnect the power steering ECU assembly connector.
| *a | Front view of wire harness connector
(to Power Steering ECU Assembly) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E102-1 (CANH) - E102-2 (CANL) | LG - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E102-1 (CANH) - E102-3 (GND) | LG - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E102-2 (CANL) - E102-3 (GND) | W - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E102-1 (CANH) - E22-16 (BAT) | LG - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E102-2 (CANL) - E22-16 (BAT) | W - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)
| *a | Component without harness connected
(Certification ECU [Smart Key ECU Assembly]) |
- | - |
Disconnect the certification ECU (smart key ECU assembly) connector.
| *a | Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly]) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E130-7 (CANH) - E130-8 (CANL) | B - W | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E130-7 (CANH) - E130-11 (E) | B - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E130-8 (CANL) - E130-11 (E) | W - BR | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E130-7 (CANH) - E130-10 (+B) | B - P | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E130-8 (CANL) - E130-10 (+B) | W - P | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK HEADLIGHT LEVELING ECU ASSEMBLY (w/ Automatic High Beam System)
| *a | Component without harness connected
(Headlight Leveling ECU Assembly) |
- | - |
Disconnect the headlight leveling ECU assembly connector.
| *a | Front view of wire harness connector
(to Headlight Leveling ECU Assembly) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E101-12 (CANH) - E101-13 (CANL) | LG - B | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E101-12 (CANH) - E101-22 (E1) | LG - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E101-13 (CANL) - E101-22 (E1) | B - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E101-12 (CANH) - E22-16 (BAT) | LG - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E101-13 (CANL) - E22-16 (BAT) | B - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK HEADLIGHT LEVELING ECU ASSEMBLY (w/o Automatic High Beam System)
| *a | Component without harness connected
(Headlight Leveling ECU Assembly) |
- | - |
Disconnect the headlight leveling ECU assembly connector.
| *a | Front view of wire harness connector
(to Headlight Leveling ECU Assembly) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E109-6 (CANH) - E109-7 (CANL) | LG - B | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E109-6 (CANH) - E109-9 (E1) | LG - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E109-7 (CANL) - E109-9 (E1) | B - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E109-6 (CANH) - E22-16 (BAT) | LG - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E109-7 (CANL) - E22-16 (BAT) | B - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Memory)
| *a | Component without harness connected
(Outer Mirror Control ECU Assembly LH) |
- | - |
Disconnect the outer mirror control ECU assembly LH connector.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| I41-9 (CANP) - I41-8 (CANN) | BE - L | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I41-9 (CANP) - I41-7 (GND) | BE - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I41-8 (CANN) - I41-7 (GND) | L - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I41-9 (CANP) - I41-6 (CPUB) | BE - G | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I41-8 (CANN) - I41-6 (CPUB) | L - G | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Memory)
| *a | Component without harness connected
(Outer Mirror Control ECU Assembly RH) |
- | - |
Disconnect the outer mirror control ECU assembly RH connector.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| I38-9 (CANP) - I38-8 (CANN) | LG - L | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I38-9 (CANP) - I38-7 (GND) | LG - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I38-8 (CANN) - I38-7 (GND) | L - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I38-9 (CANP) - I38-6 (CPUB) | LG - G | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I38-8 (CANN) - I38-6 (CPUB) | L - G | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK MULTIPLEX TILT AND TELESCOPIC ECU (w/ Power Tilt and Power Telescopic Steering Column System)
| *a | Component without harness connected
(Multiplex Tilt and Telescopic ECU) |
- | - |
Disconnect the multiplex tilt and telescopic ECU connector.
| *a | Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E144-3 (CANP) - E144-11 (CANN) | P - L | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E144-3 (CANP) - E144-1 (GND) | P - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E144-11 (CANN) - E144-1 (GND) | L - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E144-3 (CANP) - E144-2 (+B) | P - LA-W | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E144-11 (CANN) - E144-2 (+B) | L - LA-W | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK POWER SEAT SWITCH ASSEMBLY (w/ Memory)
| *a | Component without harness connected
(Power Seat Switch Assembly) |
- | - |
Disconnect the power seat switch assembly connectors.
| *a | Rear view of wire harness connector
(to Power Seat Switch Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| c40-8 (MPX1) - c40-7 (MPX2) | V - L | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| c40-8 (MPX1) - c39-1 (GND) | V - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| c40-7 (MPX2) - c39-1 (GND) | L - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| c40-8 (MPX1) - c39-6 (+B) | V - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| c40-7 (MPX2) - c39-6 (+B) | L - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU) (w/ Power Back Door System)
| *a | Component without harness connected
(Power Back Door Unit Assembly [Power Back Door ECU]) |
- | - |
Disconnect the power back door unit assembly (power back door ECU) connector.
| *a | Front view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU]) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| L52-6 (MPX1) - L52-5 (MPX2) | V - L | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| L52-6 (MPX1) - L52-11 (GND) | V - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| L52-5 (MPX2) - L52-11 (GND) | L - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| L52-6 (MPX1) - L52-10 (ECUB) | V - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L52-5 (MPX2) - L52-10 (ECUB) | L - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK NO. 2 MAIN BODY ECU (w/ Tail Gate Closer System)
| *a | Component without harness connected
(No. 2 Main Body ECU) |
- | - |
Disconnect the No. 2 main body ECU connector.
| *a | Front view of wire harness connector
(to No. 2 Main Body ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| L50-11 (MPX+) - L50-12 (MPX-) | LG - L | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| L50-11 (MPX+) - L50-7 (GND) | LG - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| L50-12 (MPX-) - L50-7 (GND) | L - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| L50-11 (MPX+) - L50-14 (BECU) | LG - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L50-12 (MPX-) - L50-14 (BECU) | L - R | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK BUS BUFFER ECU (w/ Bus Buffer ECU)
Disconnect the bus buffer ECU connector.
| *a | Front view of wire harness connector
(to Bus Buffer ECU) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
|---|---|---|---|
| E173-2 (CAN+) - E173-1 (CAN-) | BE - GR | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| E173-2 (CAN+) - E22-4 (CG) | BE - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E173-1 (CAN-) - E22-4 (CG) | GR - W-B | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E173-2 (CAN+) - E22-16 (BAT) | BE - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E173-1 (CAN-) - E22-16 (BAT) | GR - L | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |