Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255537 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  Short in CAN Bus Lines  


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.

Detection Item Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
·

Short between CAN bus lines

·

ECM

·

4WD control ECU

·

Power steering ECU assembly*1

·

Airbag sensor assembly

·

Tire pressure warning ECU*2

·

Air conditioning amplifier assembly

·

Central gateway ECU

·

Main body ECU (multiplex network body ECU)

·

Master cylinder solenoid (skid control ECU)

·

Headlight leveling ECU assembly

·

Certification ECU (smart key ECU assembly)*3

·

Steering control ECU*4

·

Steering sensor

·

Multi-media module receiver assembly*5

·

Radio and display receiver assembly*6

·

Combination meter assembly

·

DLC3 CAN branch wire or connector

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector



*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System

*3: w/ Entry and Start System

*4: w/ Variable Gear Ratio Steering System

*5: for Multi-media Module Receiver Type

*6: for Radio and Display Type


WIRING DIAGRAM

C346317E01
6.193,1.711 6.553,1.859 0.361,0.149 10 A38 6.193,1.847 6.553,1.996 0.361,0.149 10 ECM 5.958,1.399 6.461,1.548 0.503,0.149 10 CANL 5.958,0.674 6.461,0.823 0.503,0.149 10 CANH 4.841,0.674 5.883,0.823 1.042,0.149 10 10*1, 41*2, 11*3 4.841,1.21 5.908,1.359 1.068,0.149 10 11*1, 49*2, 19*3 4.095,0.674 4.598,0.823 0.503,0.149 10 7 4.095,1.21 4.598,1.359 0.503,0.149 10 17 3.208,0.674 3.711,0.823 0.503,0.149 10 2 3.142,1.21 3.645,1.359 0.503,0.149 10 12 4.095,2.639 4.598,2.788 0.503,0.149 10 3 4.095,3.175 4.598,3.324 0.503,0.149 10 13 3.208,2.639 3.711,2.788 0.503,0.149 10 4 3.142,3.175 3.645,3.324 0.503,0.149 10 14 0.224,7.053 2.003,7.201 1.779,0.149 10 *1: for 1UR-FE, 1GR-FE 0.224,7.937 1.484,8.086 1.260,0.149 10 *3: for 3UR-FE 0.224,7.495 1.734,7.644 1.510,0.149 10 *2: for 1VD-FTV 0.35,5.617 0.711,5.766 0.361,0.149 10 E173 0.35,5.757 1.969,6.104 1.619,0.348 10 Bus Buffer ECU*8 0.858,5.227 1.361,5.376 0.503,0.149 10 CAN- 0.858,4.683 1.361,4.832 0.503,0.149 10 CAN+ 1.42,4.565 1.923,4.714 0.503,0.149 10 2 1.42,5.101 1.923,5.250 0.503,0.149 10 1 4.095,4.598 4.598,4.746 0.503,0.149 10 5 4.095,5.133 4.598,5.282 0.503,0.149 10 15 3.208,4.598 3.711,4.746 0.503,0.149 10 6 3.142,5.133 3.645,5.282 0.503,0.149 10 16 2.769,6.211 3.130,6.360 0.361,0.149 10 E135 2.769,6.348 5.057,6.497 2.288,0.149 10 No. 1 CAN Junction Connector 0.866,1.321 1.369,1.470 0.503,0.149 10 CANL 0.866,0.777 1.369,0.926 0.503,0.149 10 CANH 1.403,0.64 1.906,0.789 0.503,0.149 10 20 1.403,1.176 1.906,1.325 0.503,0.149 10 40 0.28,1.714 0.641,1.863 0.361,0.149 10 A27 0.28,1.851 1.999,2.000 1.718,0.149 10 4WD Control ECU 0.156,3.643 0.517,3.792 0.361,0.149 10 E47 0.156,3.78 1.840,4.127 1.684,0.348 10 Airbag Sensor Assembly 0.866,3.269 1.369,3.418 0.503,0.149 10 CANL 0.866,2.725 1.369,2.874 0.503,0.149 10 CANH 1.403,2.588 1.906,2.737 0.503,0.149 10 13 1.403,3.124 1.906,3.273 0.503,0.149 10 22 6.023,3.257 6.526,3.406 0.503,0.149 10 CANL 6.023,2.724 6.526,2.873 0.503,0.149 10 CANH 4.913,3.537 5.329,3.686 0.416,0.149 10 E102 4.913,3.674 7.085,3.992 2.172,0.318 10 Power Steering ECU Assembly*4 5.722,3.147 6.225,3.296 0.503,0.149 10 2 5.722,2.61 6.225,2.758 0.503,0.149 10 1 5.128,4.679 5.488,4.828 0.361,0.149 10 L65 5.128,5.212 5.488,5.360 0.361,0.149 10 L65 5.576,4.679 5.937,4.828 0.361,0.149 10 L75 5.576,5.212 5.937,5.360 0.361,0.149 10 L75 5.976,5.218 6.479,5.367 0.503,0.149 10 CANL 5.976,4.686 6.479,4.835 0.503,0.149 10 CANH 5.101,5.02 5.604,5.169 0.503,0.149 10 10*5 5.129,4.483 5.632,4.632 0.503,0.149 10 9*5 5.563,5.02 6.066,5.169 0.503,0.149 10 10*6 5.591,4.483 6.094,4.632 0.503,0.149 10 9*6 5.067,5.623 7.040,5.772 1.973,0.149 10 Tire Pressure Warning ECU*7 0.224,8.379 3.558,8.528 3.334,0.149 10 *4: w/ Variable Flow Control Solenoid Valve 3.348,7.053 5.803,7.201 2.455,0.149 10 *5: w/o Front Antenna 3.348,7.495 5.803,7.644 2.455,0.149 10 *6: w/ Front Antenna 3.348,7.937 6.321,8.086 2.973,0.149 10 *7: w/ Tire Pressure Warning System 3.348,8.379 6.321,8.528 2.973,0.149 10 *8: w/ Bus Buffer ECU

C346318E01
4.123,2.427 4.626,2.576 0.503,0.149 10 1 4.123,2.963 4.626,3.112 0.503,0.149 10 11 4.123,0.465 4.626,0.614 0.503,0.149 10 1 4.123,1.001 4.626,1.150 0.503,0.149 10 11 3.167,2.427 3.670,2.576 0.503,0.149 10 2 3.1,2.963 3.603,3.112 0.503,0.149 10 12 3.167,0.465 3.670,0.614 0.503,0.149 10 8 3.1,1.001 3.603,1.150 0.503,0.149 10 18 4.123,4.392 4.626,4.541 0.503,0.149 10 3 4.123,4.928 4.626,5.077 0.503,0.149 10 13 3.167,4.392 3.670,4.541 0.503,0.149 10 4 3.1,4.928 3.603,5.077 0.503,0.149 10 14 3.18,6.365 3.684,6.514 0.503,0.149 10 8 3.11,6.9 3.614,7.049 0.503,0.149 10 18 4.129,6.364 4.632,6.513 0.503,0.149 10 6 4.129,6.9 4.632,7.049 0.503,0.149 10 16 2.727,7.664 3.088,7.813 0.361,0.149 10 E133 2.727,7.8 5.135,7.949 2.408,0.149 10 No. 2 CAN Junction Connector 2.797,1.527 3.158,1.676 0.361,0.149 10 E135 2.797,1.664 5.205,1.813 2.408,0.149 10 No. 1 CAN Junction Connector 1.393,1.038 1.896,1.187 0.503,0.149 10 4 1.393,0.505 1.896,0.654 0.503,0.149 10 3 0.347,1.512 0.708,1.661 0.361,0.149 10 E35 0.347,1.646 2.191,1.989 1.844,0.342 10 Air Conditioning Amplifier Assembly 0.911,1.122 1.414,1.271 0.503,0.149 10 CANL 0.865,0.575 1.369,0.724 0.503,0.149 10 CANH 0.911,3.086 1.414,3.235 0.503,0.149 10 CANL 0.865,2.539 1.369,2.688 0.503,0.149 10 CANH 1.377,2.962 1.880,3.111 0.503,0.149 10 13 1.377,2.43 1.880,2.579 0.503,0.149 10 14 0.105,3.41 0.624,3.559 0.518,0.149 10 E118 0.105,3.569 1.771,4.070 1.665,0.501 10 Main Body ECU (Multiplex Network Body ECU) 5.477,5.309 5.838,5.458 0.361,0.149 10 A24 5.477,5.445 7.124,5.793 1.647,0.348 10 Master Cylinder Solenoid (Skid Control ECU) 5.985,5.028 6.488,5.177 0.503,0.149 10 CANL 5.985,4.484 6.488,4.633 0.503,0.149 10 CANH 5.723,4.398 6.226,4.547 0.503,0.149 10 11 5.723,4.934 6.226,5.083 0.503,0.149 10 25 0.862,5.04 1.365,5.189 0.503,0.149 10 CANL 0.862,4.493 1.365,4.642 0.503,0.149 10 CANH 1.416,4.844 1.919,4.992 0.503,0.149 10 13*1 1.416,4.311 1.919,4.460 0.503,0.149 10 12*1 1.892,4.844 2.395,4.992 0.503,0.149 10 7*2 1.892,4.311 2.395,4.460 0.503,0.149 10 6*2 1.398,5.033 1.898,5.182 0.500,0.149 10 E101 1.398,4.497 1.898,4.646 0.500,0.149 10 E101 1.846,4.497 2.346,4.646 0.500,0.149 10 E109 1.846,5.033 2.346,5.182 0.500,0.149 10 E109 0.298,5.425 2.753,5.574 2.455,0.149 10 Headlight Leveling ECU Assembly 5.613,7.352 5.974,7.501 0.361,0.149 10 E130 5.613,7.489 7.156,7.836 1.542,0.348 10 Certification ECU (Smart Key ECU Assembly)*3 5.986,6.987 6.489,7.136 0.503,0.149 10 CANL 5.986,6.443 6.489,6.592 0.503,0.149 10 CANH 5.8,6.358 6.303,6.507 0.503,0.149 10 7 5.8,6.893 6.303,7.042 0.503,0.149 10 8 0.914,7.012 1.417,7.161 0.503,0.149 10 CNL1 0.914,6.466 1.417,6.615 0.503,0.149 10 CNH1 1.384,6.886 1.887,7.035 0.503,0.149 10 9 1.384,6.353 1.887,6.502 0.503,0.149 10 3 0.35,7.376 0.711,7.525 0.361,0.149 10 E161 0.35,7.513 2.458,7.662 2.107,0.149 10 Steering Control ECU*4 2.916,8.174 5.024,8.323 2.107,0.149 10 *3: w/ Entry and Start System 2.916,8.447 5.781,8.601 2.864,0.154 10 *4: w/ Variable Gear Ratio Steering System 0.318,8.174 2.958,8.323 2.641,0.149 10 *1: w/ Automatic High Beam System 0.318,8.447 3.909,8.601 3.591,0.154 10 *2: w/o Automatic High Beam System

C346319E03
3.135,2.323 3.646,2.5 0.51,0.177 10 false 5 3.063,2.854 3.563,3.031 0.5,0.177 10 false 15 5.146,5.427 5.583,5.573 0.438,0.146 10 false E119 5.146,5.604 7.094,5.948 1.948,0.344 10 false Combination Meter Assembly 5.885,5.26 6.385,5.406 0.5,0.146 10 false CANL 5.885,4.5 6.385,4.646 0.5,0.146 10 false CANH 5.604,4.5 6.104,4.646 0.5,0.146 10 false 39 5.635,5.031 6.135,5.177 0.5,0.146 10 false 40 4.021,4.469 4.521,4.615 0.5,0.146 10 false 7 4.021,5.01 4.521,5.156 0.5,0.146 10 false 17 2.771,5.604 4.854,5.854 2.083,0.25 10 false No. 2 CAN Junction Connector 2.771,5.427 3.208,5.573 0.438,0.146 10 false E133 1.313,2.323 1.813,2.521 0.5,0.198 10 false 1 1.313,2.854 1.813,3.063 0.5,0.208 10 false 2 0.813,2.958 1.344,3.198 0.531,0.24 10 false CANL 0.813,2.417 1.344,2.646 0.531,0.229 10 false CANH 0.26,3.333 1.844,3.698 1.583,0.365 10 false F77 0.26,3.521 2.104,4.156 1.844,0.635 10 false Multi-media Module Receiver Assembly*4 1.313,4.51 1.813,4.656 0.5,0.146 10 false 9 1.313,5.042 1.813,5.188 0.5,0.146 10 false 10 0.813,5.146 1.313,5.292 0.5,0.146 10 false CANL 0.813,4.604 1.313,4.75 0.5,0.146 10 false CANH 0.26,5.521 1.844,5.885 1.583,0.365 10 false F124 0.26,5.708 2.083,6.167 1.823,0.458 10 false Radio and Display Receiver Assembly*5 4.021,2.323 4.521,2.469 0.5,0.146 10 false 10 4.021,2.854 4.521,3 0.5,0.146 10 false 20 5.792,3.354 6.896,3.708 1.104,0.354 10 false Steering Sensor 5.885,2.958 6.385,3.104 0.5,0.146 10 false CANL 5.885,2.417 6.385,2.563 0.5,0.146 10 false CANH 4.625,2.729 5.125,2.875 0.5,0.146 10 false 3*1 4.615,2.208 5.115,2.354 0.5,0.146 10 false 4*1 4.552,2.417 4.917,2.563 0.365,0.146 10 false E108 4.552,2.948 4.917,3.094 0.365,0.146 10 false E108 5.083,2.729 5.583,2.875 0.5,0.146 10 false 2*2 5.073,2.208 5.573,2.354 0.5,0.146 10 false 3*2 5.01,2.417 5.375,2.563 0.365,0.146 10 false E121 5.01,2.948 5.375,3.094 0.365,0.146 10 false E121 5.521,2.729 6.021,2.875 0.5,0.146 10 false 2*3 5.51,2.208 6.01,2.354 0.5,0.146 10 false 3*3 5.458,2.417 5.823,2.563 0.365,0.146 10 false E163 5.458,2.948 5.823,3.094 0.365,0.146 10 false E163 4.021,0.531 4.521,0.677 0.5,0.146 10 false 9 4.021,1.063 4.521,1.208 0.5,0.146 10 false 19 6.115,1.542 6.521,1.719 0.406,0.177 10 false E22 6.115,1.688 6.521,1.865 0.406,0.177 10 false DLC3 5.885,1.167 6.385,1.313 0.5,0.146 10 false CANL 5.885,0.625 6.385,0.771 0.5,0.146 10 false CANH 5.646,1.073 6.146,1.219 0.5,0.146 10 false 14 5.719,0.531 6.219,0.677 0.5,0.146 10 false 6 0.219,6.396 5.365,6.708 5.146,0.313 10 false *1: w/o Variable Gear Ratio Steering System, w/o Entry and Start System 0.219,6.677 5.385,6.979 5.167,0.302 10 false *2: w/o Variable Gear Ratio Steering System, w/ Entry and Start System 0.219,6.948 3.448,7.24 3.229,0.292 10 false *3: w/ Variable Gear Ratio Steering System 0.219,7.219 5.365,7.542 5.146,0.323 10 false *4: for Multi-media Module Receiver Type 0.219,7.5 5.333,7.823 5.115,0.323 10 false *5: for Radio and Display Type

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS WIRES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.
U166177E02
2.406,1.177 2.625,1.063 2.625,1.063 2.667,1.063 false 1.865,0.448 1.948,0.448 1.948,0.448 2.323,0.802 false 2.031,1.833 2.115,1.833 2.115,1.833 2.396,1.313 false 2.01,0.219 2.094,0.219 2.094,0.219 2.396,0.792 false 2.406,0.896 2.583,0.469 2.583,0.469 2.667,0.469 false 0.323,1.021 0.74,1.219 0.417,0.198 10 false A38 0.094,0.063 0.427,0.302 0.333,0.24 10 false *a 1.219,0.354 1.948,0.521 0.729,0.167 10 false CANH*A 0.781,0.125 2.25,0.302 1.469,0.177 10 false CANL*A, CANH*C 2.698,0.979 3.385,1.167 0.688,0.188 10 false CANH*B 2.698,0.375 3.365,0.573 0.667,0.198 10 false CANL*C 1.375,1.75 2.094,1.938 0.719,0.188 10 false CANL*B

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1UR-FE, 1GR-FE:
Tester Connection Condition Specified Condition
A38-10 (CANH) - A38-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 1VD-FTV:
Tester Connection Condition Specified Condition
A38-41 (CANH) - A38-49 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 3UR-FE:
Tester Connection Condition Specified Condition
A38-11 (CANH) - A38-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*A for 1UR-FE
*B for 1VD-FTV
*C for 3UR-FE
*a Front view of wire harness connector
(to ECM)

Result
Result Proceed to
OK (for 1UR-FE) A
OK (for 1VD-FTV) B
OK (for 1GR-FE) C
OK (for 3UR-FE) D
NG E



A

B

C

D

E

2.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the A38 ECM connector.



NEXT

3.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
a.
U165131E01
1.539,0.276 1.951,0.414 0.412,0.137 10 E119 0.252,1.752 0.671,1.889 0.419,0.137 10 CANH 0.14,1.372 0.550,1.510 0.409,0.137 10 CANL 0.074,0.061 0.262,0.198 0.188,0.137 10 *a 0.978,1.264 0.752,1.454 0.752,1.454 0.624,1.454 false 1.061,1.264 0.939,1.845 0.939,1.845 0.76,1.845 false

Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-39 (CANH) - E119-40 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the E119 combination meter assembly connector.



NEXT

5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

U165482E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 0.932,0.84 1.275,0.982 0.343,0.142 10 E135 1.676,0.519 2.245,0.662 0.569,0.144 10 CANH*b 1.739,1.066 2.308,1.210 0.569,0.144 10 CANL*b 1.953,1.224 2.522,1.368 0.569,0.144 10 CANL*c 2.508,1.294 2.701,1.294 2.701,1.294 2.834,0.999 false 2.072,1.386 2.641,1.529 0.569,0.144 10 CANL*d 2.308,1.564 2.877,1.707 0.569,0.144 10 CANL*e 2.073,0.195 2.643,0.338 0.569,0.144 10 CANH*d 1.814,0.352 2.384,0.496 0.569,0.144 10 CANH*c 2.343,0.03 2.913,0.174 0.569,0.144 10 CANH*e 4.781,0.48 5.351,0.624 0.569,0.144 10 CANH*i 3.391,0.198 3.960,0.342 0.569,0.144 10 CANH*f 4.635,0.284 5.205,0.428 0.569,0.144 10 CANH*h 4.758,1.184 5.328,1.327 0.569,0.144 10 CANL*i 3.303,1.382 3.872,1.526 0.569,0.144 10 CANL*f 3.928,0.839 4.514,0.349 4.514,0.349 4.612,0.349 false 3.419,0.844 3.279,0.262 3.279,0.262 3.377,0.262 false 2.412,0.418 2.604,0.418 2.604,0.418 2.834,0.847 false 2.629,0.271 2.87,0.271 2.87,0.271 3.014,0.836 false 2.916,0.096 3.158,0.096 3.158,0.096 3.233,0.831 false 4.548,1.385 5.117,1.529 0.569,0.144 10 CANL*h 3.928,1.007 4.429,1.454 4.429,1.454 4.527,1.454 false 2.609,0.839 2.364,0.595 2.364,0.595 2.266,0.595 false 2.609,1.007 2.392,1.132 2.392,1.132 2.294,1.132 false 2.508,1.294 2.701,1.294 2.701,1.294 2.834,0.999 false 2.608,1.446 2.849,1.446 2.849,1.446 3.014,1.01 false 2.869,1.628 2.988,1.628 2.988,1.628 3.233,1.015 false 3.429,1.02 3.15,1.443 3.15,1.443 3.28,1.443 false 4.757,0.542 4.616,0.542 4.616,0.542 4.165,0.837 false 4.176,1.005 4.613,1.253 4.613,1.253 4.725,1.253 false 4.226,1.564 4.795,1.707 0.569,0.144 10 CANL*g 3.75,1.025 4.107,1.632 4.107,1.632 4.205,1.632 false 4.338,0.053 4.907,0.197 0.569,0.144 10 CANH*g 3.748,0.811 4.216,0.118 4.216,0.118 4.314,0.118 false

Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to 4WD Control ECU *d to Power Steering ECU Assembly (w/ Variable Flow Control Solenoid Valve)
*e to Airbag Sensor Assembly *f to Tire Pressure Warning ECU (w/ Tire Pressure Warning System)
*g to Bus Buffer ECU (w/ Bus Buffer ECU) *h to ECM
*i to Air Conditioning Amplifier Assembly - -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E135-1 (CANH) - E135-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector
E135-2 (CANH) - E135-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4WD control ECU
E135-3 (CANH) - E135-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly*1
E135-4 (CANH) - E135-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
E135-5 (CANH) - E135-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Tire pressure warning ECU*2
E135-6 (CANH) - E135-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Bus buffer ECU*3
E135-7 (CANH) - E135-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
E135-8 (CANH) - E135-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning amplifier assembly


*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System

*3: w/ Bus Buffer ECU


Result
Result Proceed to
OK A
NG (ECM CAN main wire) B
NG (No. 2 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - ECM)

C

6.CONNECT CONNECTOR

D

8.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
6.CONNECT CONNECTOR
a.

Reconnect the E135 No. 1 CAN junction connector.



NEXT

7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)
7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connector.

U165479E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 0.932,0.84 1.275,0.982 0.343,0.142 10 E133 1.676,0.519 2.245,0.662 0.569,0.144 10 CANH*b 1.793,1.047 2.363,1.191 0.569,0.144 10 CANL*b 1.904,1.231 2.473,1.375 0.569,0.144 10 CANL*c 2.459,1.301 2.652,1.301 2.652,1.301 2.834,0.999 false 2.067,1.408 2.636,1.552 0.569,0.144 10 CANL*d 2.284,1.595 2.853,1.739 0.569,0.144 10 CANL*e 2.073,0.195 2.643,0.338 0.569,0.144 10 CANH*d 1.814,0.352 2.384,0.496 0.569,0.144 10 CANH*c 2.343,0.03 2.913,0.174 0.569,0.144 10 CANH*e 4.589,0.21 5.188,0.384 0.599,0.173 10 CANH*h 5.524,0.729 6.127,0.906 0.603,0.177 10 CANH*k 4.562,0.895 5.375,0.781 5.375,0.781 5.473,0.781 false 4.963,0.575 5.566,0.752 0.603,0.177 10 CANH*j 4.767,0.42 5.353,0.580 0.585,0.160 10 CANH*i 3.59,0.034 4.160,0.177 0.569,0.144 10 CANH*f 3.373,0.841 3.345,0.105 3.345,0.105 3.558,0.105 false 4.471,0.028 5.076,0.208 0.606,0.180 10 CANH*g 4.257,1.415 4.827,1.558 0.569,0.144 10 CANL*h 5.548,1.008 6.117,1.209 0.569,0.201 10 CANL*k 5.003,1.134 5.529,1.360 0.527,0.225 10 CANL*j 4.371,1.219 4.941,1.385 0.569,0.166 10 CANL*i 4.187,1.588 4.757,1.732 0.569,0.144 10 CANL*g 3.399,1.596 3.969,1.740 0.569,0.144 10 CANL*f 3.359,1.02 3.156,1.657 3.156,1.657 3.37,1.657 false 3.928,0.839 4.447,0.286 4.447,0.286 4.545,0.286 false 2.412,0.418 2.604,0.418 2.604,0.418 2.834,0.847 false 2.629,0.271 2.87,0.271 2.87,0.271 3.014,0.836 false 2.916,0.096 3.158,0.096 3.158,0.096 3.233,0.831 false 3.737,0.826 4.213,0.105 4.213,0.105 4.427,0.105 false 3.872,1.021 4.125,1.485 4.125,1.485 4.223,1.485 false 4.366,0.839 4.815,0.64 4.815,0.64 4.913,0.64 false 4.562,0.965 5.419,1.08 5.419,1.08 5.517,1.08 false 4.366,1.049 4.858,1.192 4.858,1.192 4.957,1.192 false 2.609,0.839 2.364,0.595 2.364,0.595 2.266,0.595 false 2.609,1.007 2.447,1.113 2.447,1.113 2.349,1.113 false 2.459,1.301 2.652,1.301 2.652,1.301 2.834,0.999 false 2.603,1.469 2.844,1.469 2.844,1.469 3.014,1.01 false 2.869,1.659 2.988,1.659 2.988,1.659 3.233,1.015 false 3.695,1.02 3.926,1.657 3.926,1.657 4.14,1.657 false 4.722,0.49 4.581,0.49 4.581,0.49 4.053,0.851 false 4.064,1.019 4.228,1.299 4.228,1.299 4.34,1.299 false

Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
*c to Main Body ECU (Multiplex Network Body ECU) *d to Master Cylinder Solenoid (Skid Control ECU)
*e to Headlight Leveling ECU Assembly *f
·

to Multi-media Module Receiver Assembly (for Multimedia Module Receiver Type)

·

to Radio and Display Receiver Assembly (for Radio and Display Type)


*g to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) *h to Combination Meter Assembly
*i to Steering Sensor
to Steering Control ECU (w/ Variable Gear Ratio Steering System)
*j to DLC3
*k to Steering Control ECU (w/ Variable Gear Ratio Steering System)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E133-1 (CANH) - E133-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector
E133-2 (CANH) - E133-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
E133-3 (CANH) - E133-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Master cylinder solenoid (skid control ECU)
E133-4 (CANH) - E133-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Headlight leveling ECU assembly
E133-5 (CANH) - E133-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
·

Multi-media module receiver assembly*1

·

Radio and display receiver assembly*2


E133-6 (CANH) - E133-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)*3
E133-7 (CANH) - E133-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly
E133-8 (CANH) - E133-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering control ECU*4
E133-9 (CANH) - E133-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher DLC3
E133-10 (CANH) - E133-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering sensor


*1: for Multi-media Module Receiver Type

*2: for Radio and Display Type

*3: w/ Entry and Start System

*4: w/ Variable Gear Ratio Steering System


Result
Result Proceed to
OK A
NG (Combination meter assembly CAN main wire) B
NG (No. 1 CAN junction connector CAN main wire) C
NG (DLC3 CAN branch wires) D
NG (ECU or sensor CAN branch wires) E



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

D

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

E

8.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
8.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.
U165234E01
0.05,0 0.219,0.185 0.168,0.185 10 *a 2.33,0.273 2.796,0.458 0.466,0.185 10 CANH 1.201,1.758 1.612,1.943 0.410,0.185 10 CANL 1.965,0.847 2.16,0.354 2.16,0.354 2.287,0.354 false 1.97,1.413 1.82,1.839 1.82,1.839 1.688,1.839 false 0.227,1.06 0.503,1.200 0.276,0.140 10 E22

Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E22-6 (CANH) - E22-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of DLC3

HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR