Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255537 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  Short to GND in CAN Bus Line  


DESCRIPTION

There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.

Detection Item Trouble Area
The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
·

Short between CAN bus lines and GND

·

ECM

·

4WD control ECU

·

Power steering ECU assembly*1

·

Airbag sensor assembly

·

Tire pressure warning ECU*2

·

Air conditioning amplifier assembly

·

Central gateway ECU

·

Main body ECU (multiplex network body ECU)

·

Master cylinder solenoid (skid control ECU)

·

Headlight leveling ECU assembly

·

Certification ECU (smart key ECU assembly)*3

·

Steering control ECU*4

·

Steering sensor

·

Multi-media module receiver assembly*5

·

Radio and display receiver assembly*6

·

Combination meter assembly

·

DLC3 CAN branch wire or connector

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector



*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System

*3: w/ Entry and Start System

*4: w/ Variable Gear Ratio Steering System

*5: for Multi-media Module Receiver Type

*6: for Radio and Display Type


WIRING DIAGRAM

C346317E01
6.193,1.711 6.553,1.859 0.361,0.149 10 A38 6.193,1.847 6.553,1.996 0.361,0.149 10 ECM 5.958,1.399 6.461,1.548 0.503,0.149 10 CANL 5.958,0.674 6.461,0.823 0.503,0.149 10 CANH 4.841,0.674 5.883,0.823 1.042,0.149 10 10*1, 41*2, 11*3 4.841,1.21 5.908,1.359 1.068,0.149 10 11*1, 49*2, 19*3 4.095,0.674 4.598,0.823 0.503,0.149 10 7 4.095,1.21 4.598,1.359 0.503,0.149 10 17 3.208,0.674 3.711,0.823 0.503,0.149 10 2 3.142,1.21 3.645,1.359 0.503,0.149 10 12 4.095,2.639 4.598,2.788 0.503,0.149 10 3 4.095,3.175 4.598,3.324 0.503,0.149 10 13 3.208,2.639 3.711,2.788 0.503,0.149 10 4 3.142,3.175 3.645,3.324 0.503,0.149 10 14 0.224,7.053 2.003,7.201 1.779,0.149 10 *1: for 1UR-FE, 1GR-FE 0.224,7.937 1.484,8.086 1.260,0.149 10 *3: for 3UR-FE 0.224,7.495 1.734,7.644 1.510,0.149 10 *2: for 1VD-FTV 0.35,5.617 0.711,5.766 0.361,0.149 10 E173 0.35,5.757 1.969,6.104 1.619,0.348 10 Bus Buffer ECU*8 0.858,5.227 1.361,5.376 0.503,0.149 10 CAN- 0.858,4.683 1.361,4.832 0.503,0.149 10 CAN+ 1.42,4.565 1.923,4.714 0.503,0.149 10 2 1.42,5.101 1.923,5.250 0.503,0.149 10 1 4.095,4.598 4.598,4.746 0.503,0.149 10 5 4.095,5.133 4.598,5.282 0.503,0.149 10 15 3.208,4.598 3.711,4.746 0.503,0.149 10 6 3.142,5.133 3.645,5.282 0.503,0.149 10 16 2.769,6.211 3.130,6.360 0.361,0.149 10 E135 2.769,6.348 5.057,6.497 2.288,0.149 10 No. 1 CAN Junction Connector 0.866,1.321 1.369,1.470 0.503,0.149 10 CANL 0.866,0.777 1.369,0.926 0.503,0.149 10 CANH 1.403,0.64 1.906,0.789 0.503,0.149 10 20 1.403,1.176 1.906,1.325 0.503,0.149 10 40 0.28,1.714 0.641,1.863 0.361,0.149 10 A27 0.28,1.851 1.999,2.000 1.718,0.149 10 4WD Control ECU 0.156,3.643 0.517,3.792 0.361,0.149 10 E47 0.156,3.78 1.840,4.127 1.684,0.348 10 Airbag Sensor Assembly 0.866,3.269 1.369,3.418 0.503,0.149 10 CANL 0.866,2.725 1.369,2.874 0.503,0.149 10 CANH 1.403,2.588 1.906,2.737 0.503,0.149 10 13 1.403,3.124 1.906,3.273 0.503,0.149 10 22 6.023,3.257 6.526,3.406 0.503,0.149 10 CANL 6.023,2.724 6.526,2.873 0.503,0.149 10 CANH 4.913,3.537 5.329,3.686 0.416,0.149 10 E102 4.913,3.674 7.085,3.992 2.172,0.318 10 Power Steering ECU Assembly*4 5.722,3.147 6.225,3.296 0.503,0.149 10 2 5.722,2.61 6.225,2.758 0.503,0.149 10 1 5.128,4.679 5.488,4.828 0.361,0.149 10 L65 5.128,5.212 5.488,5.360 0.361,0.149 10 L65 5.576,4.679 5.937,4.828 0.361,0.149 10 L75 5.576,5.212 5.937,5.360 0.361,0.149 10 L75 5.976,5.218 6.479,5.367 0.503,0.149 10 CANL 5.976,4.686 6.479,4.835 0.503,0.149 10 CANH 5.101,5.02 5.604,5.169 0.503,0.149 10 10*5 5.129,4.483 5.632,4.632 0.503,0.149 10 9*5 5.563,5.02 6.066,5.169 0.503,0.149 10 10*6 5.591,4.483 6.094,4.632 0.503,0.149 10 9*6 5.067,5.623 7.040,5.772 1.973,0.149 10 Tire Pressure Warning ECU*7 0.224,8.379 3.558,8.528 3.334,0.149 10 *4: w/ Variable Flow Control Solenoid Valve 3.348,7.053 5.803,7.201 2.455,0.149 10 *5: w/o Front Antenna 3.348,7.495 5.803,7.644 2.455,0.149 10 *6: w/ Front Antenna 3.348,7.937 6.321,8.086 2.973,0.149 10 *7: w/ Tire Pressure Warning System 3.348,8.379 6.321,8.528 2.973,0.149 10 *8: w/ Bus Buffer ECU

C346318E01
4.123,2.427 4.626,2.576 0.503,0.149 10 1 4.123,2.963 4.626,3.112 0.503,0.149 10 11 4.123,0.465 4.626,0.614 0.503,0.149 10 1 4.123,1.001 4.626,1.150 0.503,0.149 10 11 3.167,2.427 3.670,2.576 0.503,0.149 10 2 3.1,2.963 3.603,3.112 0.503,0.149 10 12 3.167,0.465 3.670,0.614 0.503,0.149 10 8 3.1,1.001 3.603,1.150 0.503,0.149 10 18 4.123,4.392 4.626,4.541 0.503,0.149 10 3 4.123,4.928 4.626,5.077 0.503,0.149 10 13 3.167,4.392 3.670,4.541 0.503,0.149 10 4 3.1,4.928 3.603,5.077 0.503,0.149 10 14 3.18,6.365 3.684,6.514 0.503,0.149 10 8 3.11,6.9 3.614,7.049 0.503,0.149 10 18 4.129,6.364 4.632,6.513 0.503,0.149 10 6 4.129,6.9 4.632,7.049 0.503,0.149 10 16 2.727,7.664 3.088,7.813 0.361,0.149 10 E133 2.727,7.8 5.135,7.949 2.408,0.149 10 No. 2 CAN Junction Connector 2.797,1.527 3.158,1.676 0.361,0.149 10 E135 2.797,1.664 5.205,1.813 2.408,0.149 10 No. 1 CAN Junction Connector 1.393,1.038 1.896,1.187 0.503,0.149 10 4 1.393,0.505 1.896,0.654 0.503,0.149 10 3 0.347,1.512 0.708,1.661 0.361,0.149 10 E35 0.347,1.646 2.191,1.989 1.844,0.342 10 Air Conditioning Amplifier Assembly 0.911,1.122 1.414,1.271 0.503,0.149 10 CANL 0.865,0.575 1.369,0.724 0.503,0.149 10 CANH 0.911,3.086 1.414,3.235 0.503,0.149 10 CANL 0.865,2.539 1.369,2.688 0.503,0.149 10 CANH 1.377,2.962 1.880,3.111 0.503,0.149 10 13 1.377,2.43 1.880,2.579 0.503,0.149 10 14 0.105,3.41 0.624,3.559 0.518,0.149 10 E118 0.105,3.569 1.771,4.070 1.665,0.501 10 Main Body ECU (Multiplex Network Body ECU) 5.477,5.309 5.838,5.458 0.361,0.149 10 A24 5.477,5.445 7.124,5.793 1.647,0.348 10 Master Cylinder Solenoid (Skid Control ECU) 5.985,5.028 6.488,5.177 0.503,0.149 10 CANL 5.985,4.484 6.488,4.633 0.503,0.149 10 CANH 5.723,4.398 6.226,4.547 0.503,0.149 10 11 5.723,4.934 6.226,5.083 0.503,0.149 10 25 0.862,5.04 1.365,5.189 0.503,0.149 10 CANL 0.862,4.493 1.365,4.642 0.503,0.149 10 CANH 1.416,4.844 1.919,4.992 0.503,0.149 10 13*1 1.416,4.311 1.919,4.460 0.503,0.149 10 12*1 1.892,4.844 2.395,4.992 0.503,0.149 10 7*2 1.892,4.311 2.395,4.460 0.503,0.149 10 6*2 1.398,5.033 1.898,5.182 0.500,0.149 10 E101 1.398,4.497 1.898,4.646 0.500,0.149 10 E101 1.846,4.497 2.346,4.646 0.500,0.149 10 E109 1.846,5.033 2.346,5.182 0.500,0.149 10 E109 0.298,5.425 2.753,5.574 2.455,0.149 10 Headlight Leveling ECU Assembly 5.613,7.352 5.974,7.501 0.361,0.149 10 E130 5.613,7.489 7.156,7.836 1.542,0.348 10 Certification ECU (Smart Key ECU Assembly)*3 5.986,6.987 6.489,7.136 0.503,0.149 10 CANL 5.986,6.443 6.489,6.592 0.503,0.149 10 CANH 5.8,6.358 6.303,6.507 0.503,0.149 10 7 5.8,6.893 6.303,7.042 0.503,0.149 10 8 0.914,7.012 1.417,7.161 0.503,0.149 10 CNL1 0.914,6.466 1.417,6.615 0.503,0.149 10 CNH1 1.384,6.886 1.887,7.035 0.503,0.149 10 9 1.384,6.353 1.887,6.502 0.503,0.149 10 3 0.35,7.376 0.711,7.525 0.361,0.149 10 E161 0.35,7.513 2.458,7.662 2.107,0.149 10 Steering Control ECU*4 2.916,8.174 5.024,8.323 2.107,0.149 10 *3: w/ Entry and Start System 2.916,8.447 5.781,8.601 2.864,0.154 10 *4: w/ Variable Gear Ratio Steering System 0.318,8.174 2.958,8.323 2.641,0.149 10 *1: w/ Automatic High Beam System 0.318,8.447 3.909,8.601 3.591,0.154 10 *2: w/o Automatic High Beam System

C346319E05
3.135,2.323 3.646,2.5 0.51,0.177 10 false 5 3.063,2.854 3.563,3.031 0.5,0.177 10 false 15 5.146,5.427 5.583,5.573 0.438,0.146 10 false E119 5.146,5.604 7.094,5.948 1.948,0.344 10 false Combination Meter Assembly 5.885,5.26 6.385,5.406 0.5,0.146 10 false CANL 5.885,4.5 6.385,4.646 0.5,0.146 10 false CANH 5.604,4.5 6.104,4.646 0.5,0.146 10 false 39 5.635,5.031 6.135,5.177 0.5,0.146 10 false 40 4.021,4.469 4.521,4.615 0.5,0.146 10 false 7 4.021,5.01 4.521,5.156 0.5,0.146 10 false 17 2.771,5.604 4.854,5.854 2.083,0.25 10 false No. 2 CAN Junction Connector 2.771,5.427 3.208,5.573 0.438,0.146 10 false E133 1.313,2.323 1.813,2.521 0.5,0.198 10 false 1 1.313,2.854 1.813,3.063 0.5,0.208 10 false 2 0.813,2.958 1.344,3.198 0.531,0.24 10 false CANL 0.813,2.417 1.344,2.646 0.531,0.229 10 false CANH 0.26,3.333 1.844,3.698 1.583,0.365 10 false F77 0.26,3.521 2.104,4.156 1.844,0.635 10 false Multi-media Module Receiver Assembly*4 1.313,4.51 1.813,4.656 0.5,0.146 10 false 9 1.313,5.042 1.813,5.188 0.5,0.146 10 false 10 0.813,5.146 1.313,5.292 0.5,0.146 10 false CANL 0.813,4.604 1.313,4.75 0.5,0.146 10 false CANH 0.26,5.521 1.844,5.885 1.583,0.365 10 false F124 0.26,5.708 2.083,6.167 1.823,0.458 10 false Radio and Display Receiver Assembly*5 4.021,2.323 4.521,2.469 0.5,0.146 10 false 10 4.021,2.854 4.521,3 0.5,0.146 10 false 20 5.781,3.344 7.094,3.771 1.313,0.427 10 false Steering Sensor 5.885,2.958 6.385,3.104 0.5,0.146 10 false CANL 5.885,2.417 6.385,2.563 0.5,0.146 10 false CANH 4.625,2.729 5.125,2.875 0.5,0.146 10 false 3*1 4.615,2.208 5.115,2.354 0.5,0.146 10 false 4*1 4.552,2.417 4.917,2.563 0.365,0.146 10 false E108 4.552,2.948 4.917,3.094 0.365,0.146 10 false E108 5.083,2.729 5.583,2.875 0.5,0.146 10 false 2*2 5.073,2.208 5.573,2.354 0.5,0.146 10 false 3*2 5.01,2.417 5.375,2.563 0.365,0.146 10 false E121 5.01,2.948 5.375,3.094 0.365,0.146 10 false E121 5.521,2.729 6.021,2.875 0.5,0.146 10 false 2*3 5.51,2.208 6.01,2.354 0.5,0.146 10 false 3*3 5.458,2.417 5.823,2.563 0.365,0.146 10 false E163 5.458,2.948 5.823,3.094 0.365,0.146 10 false E163 4.021,0.531 4.521,0.677 0.5,0.146 10 false 9 4.021,1.063 4.521,1.208 0.5,0.146 10 false 19 6.115,1.542 6.521,1.719 0.406,0.177 10 false E22 6.115,1.688 6.521,1.865 0.406,0.177 10 false DLC3 5.885,1.167 6.385,1.313 0.5,0.146 10 false CANL 5.885,0.625 6.385,0.771 0.5,0.146 10 false CANH 5.646,1.073 6.146,1.219 0.5,0.146 10 false 14 5.719,0.531 6.219,0.677 0.5,0.146 10 false 6 0.219,6.396 5.365,6.708 5.146,0.313 10 false *1: w/o Variable Gear Ratio Steering System, w/o Entry and Start System 0.219,6.677 5.385,6.979 5.167,0.302 10 false *2: w/o Variable Gear Ratio Steering System, w/ Entry and Start System 0.219,6.948 3.448,7.24 3.229,0.292 10 false *3: w/ Variable Gear Ratio Steering System 0.219,7.219 5.365,7.542 5.146,0.323 10 false *4: for Multi-media Module Receiver Type 0.219,7.5 5.333,7.823 5.115,0.323 10 false *5: for Radio and Display Type

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.
U165123E02
1.229,2.115 1.344,2.115 1.344,2.115 1.656,2.458 true 2.427,0.927 3.115,2.073 3.115,2.073 3.021,2.073 true 1.885,0.385 1.99,0.385 1.99,0.385 2.344,0.813 true 1.885,1.917 1.99,1.917 1.99,1.917 2.427,1.333 true 0.823,0.479 0.927,0.479 0.927,0.479 2.427,1.24 true 2,0.219 2.115,0.219 2.115,0.219 2.427,0.813 true 0.906,2.031 1.26,2.219 0.354,0.188 10 false CG 0.083,0.031 0.406,0.198 0.323,0.167 10 false *a 0.083,1.802 0.469,2 0.385,0.198 10 false *b 0.271,1.01 0.708,1.208 0.438,0.198 10 false A38 0.396,2.604 0.781,2.854 0.385,0.25 10 false E22 1.271,0.302 1.969,0.49 0.698,0.188 10 false CANH*A 0.823,0.156 2.135,0.365 1.313,0.208 10 false CANL*A, CANH*C 0.219,0.406 0.938,0.594 0.719,0.188 10 false CANH*B 1.281,1.833 1.99,2.031 0.708,0.198 10 false CANL*B 2.417,1.99 3.083,2.188 0.667,0.198 10 false CANL*C

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1UR-FE, 1GR-FE:
Tester Connection Condition Specified Condition
A38-10 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-11 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher

for 1VD-FTV:
Tester Connection Condition Specified Condition
A38-41 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-49 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher

for 3UR-FE:
Tester Connection Condition Specified Condition
A38-11 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-19 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*A for 1UR-FE, 1GR-FE
*B for 1VD-FTV
*C for 3UR-FE
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3

Result
Result Proceed to
OK (for 1UR-FE) A
OK (for 1VD-FTV) B
OK (for 1GR-FE) C
OK (for 3UR-FE) D
NG E



A

B

C

D

E

2.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the A38 ECM connector.



NEXT

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
a.
U165151E02
0.938,1.073 0.688,1.26 0.688,1.26 0.573,1.26 false 1.021,1.063 0.875,1.594 0.875,1.594 0.74,1.594 false 1.208,1.969 1.313,1.969 1.313,1.969 1.635,2.313 false 0.104,0.042 0.396,0.198 0.292,0.156 10 false *a 0.104,1.781 0.396,1.938 0.292,0.156 10 false *b 2.75,0.438 3.219,0.635 0.469,0.198 10 false E119 0.406,2.531 0.802,2.729 0.396,0.198 10 false E22 0.146,1.177 0.667,1.354 0.521,0.177 10 false CANL 0.281,1.51 0.823,1.698 0.542,0.188 10 false CANH 0.927,1.885 1.25,2.073 0.323,0.188 10 false CG

Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-39 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E119-40 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)
*b Front view of DLC3



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the E119 combination meter assembly connector.



NEXT

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

U165505E01
0.09,0.045 0.315,0.215 0.225,0.170 10 *a 4.466,0.045 4.691,0.215 0.225,0.170 10 *b 0.135,0.659 0.704,0.803 0.569,0.144 10 CANH*c 0.142,0.993 0.711,1.136 0.569,0.144 10 CANL*c 0.217,1.149 0.786,1.292 0.569,0.144 10 CANL*d 0.772,1.218 0.965,1.218 0.965,1.218 1.405,1.027 false 0.312,1.306 0.881,1.450 0.569,0.144 10 CANL*e 0.41,1.465 0.979,1.609 0.569,0.144 10 CANL*f 0.392,0.335 0.962,0.479 0.569,0.144 10 CANH*e 0.273,0.493 0.842,0.636 0.569,0.144 10 CANH*d 0.522,0.17 1.091,0.314 0.569,0.144 10 CANH*f 3.145,0.252 3.714,0.396 0.569,0.144 10 CANH*i 0.66,0.03 1.230,0.173 0.569,0.144 10 CANH*g 2.907,0.056 3.476,0.200 0.569,0.144 10 CANH*h 3.004,1.407 3.573,1.550 0.569,0.144 10 CANL*i 2.772,1.614 3.342,1.757 0.569,0.144 10 CANL*h 0.477,1.61 1.046,1.754 0.569,0.144 10 CANL*g 2.007,0.194 2.350,0.336 0.343,0.142 10 E135 2.762,0.839 3.197,0.484 3.197,0.484 3.295,0.484 false 2.397,0.844 2.791,0.109 2.791,0.109 2.889,0.109 false 1.208,0.839 0.823,0.735 0.823,0.735 0.725,0.735 false 0.87,0.558 1.063,0.558 1.063,0.558 1.433,0.847 false 0.947,0.411 1.189,0.411 1.189,0.411 1.587,0.836 false 1.095,0.236 1.336,0.236 1.336,0.236 1.792,0.831 false 1.235,0.096 1.476,0.096 1.476,0.096 1.974,0.831 false 2.584,0.841 2.908,0.313 2.908,0.313 3.121,0.313 false 2.776,1.021 3.104,1.294 3.104,1.294 3.202,1.294 false 2.397,1.017 2.626,1.66 2.626,1.66 2.724,1.66 false 1.208,1.007 0.795,1.058 0.795,1.058 0.697,1.058 false 0.772,1.218 0.965,1.218 0.965,1.218 1.405,1.027 false 0.848,1.367 1.089,1.367 1.089,1.367 1.587,1.01 false 0.932,1.535 1.173,1.535 1.173,1.535 1.797,1.024 false 1.044,1.675 1.285,1.675 1.285,1.675 1.965,1.024 false 2.584,1.02 2.817,1.475 2.817,1.475 2.981,1.475 false 5.887,0.142 6.156,0.284 0.269,0.142 10 E22 3.241,1.228 3.811,1.371 0.569,0.144 10 CANL*j 3.327,0.43 3.897,0.573 0.569,0.144 10 CANH*j 5.002,0.29 5.290,0.432 0.288,0.142 10 CG 5.267,0.357 5.357,0.357 5.357,0.357 5.616,0.631 false

Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3
*c to No. 2 CAN Junction Connector *d to 4WD Control ECU
*e to Power Steering ECU Assembly (w/ Variable Flow Control Solenoid Valve) *f to Airbag Sensor Assembly
*g to Tire Pressure Warning ECU (w/ Tire Pressure Warning System) *h to Bus Buffer ECU (w/ Bus Buffer ECU)
*i to ECM *j to Air Conditioning Amplifier Assembly


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E135-1 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 2 CAN junction connector
E135-11 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-2 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4WD control ECU
E135-12 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-3 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly*1
E135-13 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-4 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
E135-14 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-5 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Tire pressure warning ECU*2
E135-15 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-6 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Bus buffer ECU*3
E135-16 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-7 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
E135-17 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E135-8 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning amplifier assembly
E135-18 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System

*3: w/ Bus Buffer ECU


Result
Result Proceed to
OK A
NG (ECM CAN main wire) B
NG (No. 2 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - ECM)

C

6.CONNECT CONNECTOR

D

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
6.CONNECT CONNECTOR
a.

Reconnect the E135 No. 1 CAN junction connector.



NEXT

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connector.

U165506E01
0.113,0.012 0.339,0.182 0.225,0.170 10 *a 4.662,0.012 4.887,0.182 0.225,0.170 10 *b 0.502,0.111 0.845,0.253 0.343,0.142 10 E133 0.365,0.657 0.934,0.801 0.569,0.144 10 CANH*c 0.398,0.993 0.967,1.136 0.569,0.144 10 CANL*c 0.498,1.137 1.067,1.280 0.569,0.144 10 CANL*d 1.053,1.206 1.162,1.206 1.162,1.206 1.414,0.966 false 0.736,1.271 1.305,1.415 0.569,0.144 10 CANL*e 0.762,0.333 1.332,0.477 0.569,0.144 10 CANH*e 0.503,0.491 1.072,0.634 0.569,0.144 10 CANH*d 3.395,0.696 3.964,0.840 0.569,0.144 10 CANH*l 2.551,0.17 3.121,0.314 0.569,0.144 10 CANH*i 2.249,0 2.819,0.144 0.569,0.144 10 CANH*h 3.457,1.05 4.026,1.194 0.569,0.144 10 CANL*l 2.389,1.457 2.959,1.600 0.569,0.144 10 CANL*i 3.405,0.406 3.974,0.550 0.569,0.144 10 CANH*k 2.933,0.818 3.297,0.474 3.297,0.474 3.395,0.474 false 3.258,0.178 3.827,0.322 0.569,0.144 10 CANH*j 2.78,0.82 3.15,0.246 3.15,0.246 3.248,0.246 false 2.401,0.824 2.109,0.063 2.109,0.063 2.208,0.063 false 1.1,0.556 1.167,0.556 1.167,0.556 1.414,0.814 false 1.318,0.409 1.419,0.409 1.419,0.409 1.594,0.803 false 1.032,0.169 1.601,0.312 0.569,0.144 10 CANH*f 1.605,0.234 1.734,0.234 1.734,0.234 1.813,0.798 false 1.263,0 1.833,0.144 0.569,0.144 10 CANH*g 1.836,0.056 1.966,0.056 1.966,0.056 2.029,0.793 false 2.589,0.821 2.331,0.236 2.331,0.236 2.545,0.236 false 2.401,0.984 1.95,1.674 1.95,1.674 2.048,1.674 false 3.109,0.806 3.271,0.749 3.271,0.749 3.369,0.749 false 3.095,0.974 3.316,1.117 3.316,1.117 3.414,1.117 false 1.19,0.806 1.053,0.733 1.053,0.733 0.955,0.733 false 1.19,0.974 1.051,1.058 1.051,1.058 0.953,1.058 false 1.053,1.206 1.162,1.206 1.162,1.206 1.414,0.966 false 1.286,1.346 1.36,1.346 1.36,1.346 1.594,0.977 false 0.971,1.416 1.541,1.560 0.569,0.144 10 CANL*f 1.493,1.486 1.567,1.486 1.567,1.486 1.79,0.991 false 1.125,1.571 1.695,1.714 0.569,0.144 10 CANL*g 1.648,1.64 1.721,1.64 1.721,1.64 2.018,0.989 false 2.794,0.988 2.975,1.607 2.975,1.607 3.073,1.607 false 3.099,1.535 3.668,1.679 0.569,0.144 10 CANL*j 2.589,0.987 2.286,1.519 2.286,1.519 2.36,1.519 false 6.049,0.132 6.321,0.279 0.272,0.148 10 E22 2.074,1.614 2.644,1.758 0.569,0.144 10 CANL*h 2.94,0.986 3.063,1.348 3.063,1.348 3.161,1.348 false 3.186,1.276 3.756,1.420 0.569,0.144 10 CANL*k 4.999,0.267 5.287,0.409 0.288,0.142 10 CG 5.263,0.334 5.353,0.334 5.353,0.334 5.613,0.608 false

Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3
*c to No. 1 CAN Junction Connector *d to Main Body ECU (Multiplex Network Body ECU)
*e to Master Cylinder Solenoid (Skid Control ECU) *f to Headlight Leveling ECU Assembly
*g
·

to Multi-media Module Receiver Assembly (for Multi-media Module Receiver Type)

·

to Radio and Display Receiver Assembly (for Radio and Display Type)


*h to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System)
*i to Combination Meter Assembly *j to Steering Control ECU (w/ Variable Gear Ratio Steering System)
*k to DLC3 *l to Steering Sensor


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E133-1 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 CAN junction connector
E133-11 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-2 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
E133-12 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-3 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Master cylinder solenoid (skid control ECU)
E133-13 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-4 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Headlight leveling ECU assembly
E133-14 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-5 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
·

Multi-media module receiver assembly*1

·

Radio and display receiver assembly*2


E133-15 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-6 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)*3
E133-16 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-7 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination meter assembly
E133-17 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-8 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering control ECU*4
E133-18 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-9 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher DLC3
E133-19 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E133-10 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering sensor
E133-20 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


*1: for Multi-media Module Receiver Type

*2: for Radio and Display Type

*3: w/ Entry and Start System

*4: w/ Variable Gear Ratio Steering System


Result
Result Proceed to
OK A
NG (Combination meter assembly CAN main wire) B
NG (No. 1 CAN junction connector CAN main wire) C
NG (DLC3 CAN branch wires) D
NG (ECU or sensor CAN branch wires) E



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

D

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

E

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.
U165236E02
1.594,0.906 1.396,0.417 1.396,0.417 1.271,0.417 false 1.948,0.906 2.135,0.417 2.135,0.417 2.271,0.417 false 1.958,1.469 1.813,1.896 1.813,1.896 1.677,1.896 false 0.052,0.042 0.427,0.26 0.375,0.219 10 false *a 2.323,0.333 2.885,0.542 0.563,0.208 10 false CANH 0.99,0.333 1.458,0.531 0.469,0.198 10 false CG 1.219,1.823 1.74,2.01 0.521,0.188 10 false CANL 0.24,1.104 0.604,1.323 0.365,0.219 10 false E22

Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E22-6 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E22-14 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Front view of DLC3

HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR