Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255537 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  Steering Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Control ECU Communication Stop Mode Either Condition is met:
·

"Steering Control (VGRS)" is not displayed on the "Bus Check" screen (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Steering Control ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Steering control ECU CAN branch wire or connector

·

Power source circuit of steering control ECU

·

Steering control ECU ground circuit

·

Steering control ECU



WIRING DIAGRAM

C256392E14
5.648,5.196 6.122,5.334 0.474,0.137 10 PGD2 5.648,4.617 6.122,4.754 0.474,0.137 10 PGND 5.648,4.026 6.014,4.164 0.367,0.137 10 IG 5.648,3.312 6.014,3.449 0.367,0.137 10 PIG 1.578,2.597 2.361,2.735 0.783,0.137 10 from Battery 1.578,3.312 2.361,3.449 0.783,0.137 10 from Battery 1.038,4.03 3.259,4.167 2.221,0.137 10 from IG1 NO.3 Relay 3.374,3.89 4.260,4.028 0.886,0.137 10 ECU-IG NO.1 3.611,3.17 4.028,3.308 0.417,0.137 10 VGRS 3.449,2.451 4.187,2.588 0.738,0.137 10 J/B-B NO.1 5.648,2.598 6.014,2.735 0.367,0.137 10 +BI 5.613,1.38 6.045,1.517 0.433,0.137 10 CNL1 5.627,0.851 6.059,0.988 0.433,0.137 10 CNH1 5.151,0.851 5.500,0.988 0.349,0.137 10 E161 5.277,0.637 5.376,0.775 0.099,0.137 10 3 5.277,1.166 5.376,1.304 0.099,0.137 10 9 5.151,1.38 5.500,1.517 0.349,0.137 10 E161 5.144,2.588 5.493,2.726 0.349,0.137 10 E161 5.144,3.31 5.493,3.448 0.349,0.137 10 E159 5.144,4.617 5.493,4.754 0.349,0.137 10 E159 5.27,2.375 5.369,2.512 0.099,0.137 10 7 5.144,4.021 5.493,4.158 0.349,0.137 10 E161 5.27,3.807 5.369,3.945 0.099,0.137 10 4 5.264,4.403 5.364,4.541 0.099,0.137 10 1 5.264,3.097 5.364,3.234 0.099,0.137 10 2 5.144,5.194 5.493,5.332 0.349,0.137 10 E161 5.232,4.981 5.406,5.118 0.173,0.137 10 13 5.414,5.878 6.783,6.016 1.369,0.137 10 Steering Control ECU 1.641,0.746 1.967,0.883 0.326,0.137 10 8 1.641,1.257 1.967,1.395 0.326,0.137 10 18 0.462,1.712 0.998,1.848 0.536,0.137 10 E133 0.462,1.866 2.394,2.002 1.932,0.137 10 No. 2 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (STEERING CONTROL ECU CAN BRANCH WIRE)
a.
U165184E01
1.336,1.422 1.011,1.941 1.011,1.941 0.814,1.941 false 1.336,1.146 0.861,0.628 0.861,0.628 0.663,0.628 false 0.179,0.545 0.581,0.681 0.402,0.137 10 CNH1 0.361,1.856 0.737,1.993 0.376,0.137 10 CNL1 0.059,0.049 0.421,0.186 0.362,0.137 10 *a 1.464,0.25 1.827,0.387 0.362,0.137 10 E161

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the steering control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E161-3 (CNH1) - E161-9 (CNL1) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Control ECU)



OK

2.CHECK HARNESS AND CONNECTOR (STEERING CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING CONTROL ECU (CNH1, CNL1)

2.CHECK HARNESS AND CONNECTOR (STEERING CONTROL ECU - BATTERY AND BODY GROUND)
a.
U165185E01
1.937,0.987 2.217,1.31 2.217,1.31 2.415,1.31 false 1.457,0.987 1.177,1.31 1.177,1.31 0.979,1.31 false 0.458,1.226 0.890,1.362 0.432,0.137 10 PGND 2.443,1.226 2.820,1.470 0.378,0.244 10 PIG 0.614,1.855 0.789,1.992 0.175,0.137 10 IG 0.059,0.049 0.421,0.186 0.362,0.137 10 *a 0.536,0.739 0.887,0.876 0.351,0.137 10 E159 0.24,2.356 0.590,2.493 0.351,0.137 10 E161 1.473,2.471 1.023,1.931 1.023,1.931 0.825,1.931 false 2.812,2.182 3.220,2.319 0.408,0.137 10 PGD2 0.251,2.864 0.659,3.001 0.408,0.137 10 +BI 1.093,2.712 0.795,2.951 0.795,2.951 0.598,2.951 false 2.282,2.492 2.58,2.253 2.58,2.253 2.777,2.253 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the steering control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E159-2 (PIG) - Body ground Always 11 to 14 V
E161-7 (+BI) - Body ground Always 11 to 14 V
E161-4 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E159-1 (PGND) - Body ground Always Below 1 Ω
E161-13 (PGD2) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Steering Control ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR